Difference between revisions of "NanoPi NEO Core2"

Revision as of 03:36, 23 January 2018

查看中文

1 Introduction

Overview

Front

Back

• The NanoPi NEO Core2 as its name tells is an alternative NanoPi NEO2 that works like a CPU board with male pin-headers. It has the same form facotor as the NanoPi NEO2, same pin descriptions and works with all the OS images the NanoPi NEO2 supports. The connectors and ports on the NEO2 are populated to pin-headers on the NEO2 Core. In addition the NEO Core2 can have an optional onboard eMMC flash and ESD protection for connectors and ports. There features are highly preferred by industrial customers.
• The NEO2 Core uses a popular Allwinner H5 SoC and has onboard 1G DDR3 RAM. FriendlyElec offers models with three eMMC options: 8GB(default)/16GB/32GB. FriendlyElec migrated UbuntuCore with mainline kernel 4.11 for it. It works with other OS such as Armbian as well. Compared to the NanoPi NEO2 the NanoPi NEO Core2 runs more reliably with much less overheat. It is a good platform for IoT applications, mornitoring systems, smart control systems, cluster computing and AI applications.
• FriendlyElec develops a Mini Shield for NanoPi NEO Core/Core2 which has the same form factor as the RPi 3. When a NanoPi NEO Core2 is connected to this Mini Shield the whole assembled module can be well fit into a common RPi 3's case.

2 Hardware Spec

• CPU: Allwinner H5, Quad-core 64-bit high-performance Cortex A53
• DDR3 RAM: 512MB/1GB
• Storage: 8GB/16GB/32GB eMMC
• Connectivity: 10/100/1000M Ethernet utilizing RTL8211E-VB-CG
• USB Host x 3(included in 2.54mm pitch pin header)
• MicroSD Slot x 1
• LED: x 2, one for power status and the other for system status
• GPIO1: 2.54mm pitch 12 x 2 pin header containing UART, SPI, I2C, GPIO and etc
• GPIO2: 2.54mm pitch 24 pin header containing SPI, IR, I2S, USB, serial debug port, audio and etc
• GPIO3: 2.54mm pitch 20 pin header containing USB, Gbps Ethernet, I2C and etc
• PCB Size: 40 x 40mm
• MicroUSB: OTG and power input
• OS/Software: u-boot,Ubuntu Core
• Weight: xxg(Without Pin-headers)

3 Diagram, Layout and Dimension

3.1 Layout

NanoPi NEO Core2 Layout

pinout

• GPIO1 Pin Description

Pin#	Name	Linux gpio	Pin#	Name	Linux gpio
1	SYS_3.3V		2	VDD_5V
3	I2C0_SDA / GPIOA12	12	4	VDD_5V
5	I2C0_SCL / GPIOA11	11	6	GND
7	GPIOG11	203	8	UART1_TX / GPIOG6	198
9	GND		10	UART1_RX / GPIOG7	199
11	UART2_TX / GPIOA0	0	12	GPIOA6	6
13	UART2_RTS / GPIOA2	2	14	GND
15	UART2_CTS / GPIOA3	3	16	UART1_RTS / GPIOG8	200
17	SYS_3.3V		18	UART1_CTS / GPIOG9	201
19	SPI0_MOSI / GPIOC0	64	20	GND
21	SPI0_MISO / GPIOC1	65	22	UART2_RX / GPIOA1	1
23	SPI0_CLK / GPIOC2	66	24	SPI0_CS / GPIOC3	67

• GPIO2 Pin Description

Pin#	Name	Description	Pin#	Name	Description
1	VDD_5V		2	MOSI1	SPI1-MOSI
3	USB-DP1	USB1 DP Signal	4	MISO1	SPI1-MISO
5	USB-DM1	USB1 DM Signal	6	CLK1	SPI1-CLK
7	USB-DP2	USB2 DP Signal	8	CS1	SPI1-CS
9	USB-DM2	USB2 DM Signal	10	MP	Microphone Positive Input
11	GPIOL11 / IR-RX	GPIOL11 or IR Receive	12	MN	Microphone Negative Input
13	SPDIF-OUT / GPIOA17	GPIOA17 or SPDIF-OUT	14	LR	LINE-OUT Right Channel Output
15	PCM0_SYNC / I2S0_LRCK/I2C1_SCL	I2S/PCM Sample Rate Clock/Sync	16	LL	LINE-OUT Left Channel Output
17	PCM0_CLK / I2S0_BCK/I2C1_SDA	I2S/PCM Sample Rate Clock	18	RXD	UART_RXD0/GPIOA5/PWM0
19	PCM0_DOUT / I2S0_SDOUT	I2S/PCM Serial Bata Output	20	TXD	UART_TXD0/GPIOA4
21	PCM0_DIN / I2S0_SDIN	I2S/PCM Serial Data Input	22	VDD_5V
23	GND	0V	24	GND	0V

• GPIO3 Pin Description

Pin#	Name	Description	Pin#	Name	Description
1	LINK-LED	Ethernet Link LED	2	SPEED-LED	Ethernet Speed LED
3	TRD1+	Ethernet TRD1+ Signal	4	TRD1-	Ethernet TRD1- Signal
5	TRD2+	Ethernet TRD2+ Signal	6	TRD2-	Ethernet TRD2- Signal
7	TRD3+	Ethernet TRD3+ Signal	8	TRD3-	Ethernet TRD3- Signal
9	TRD4+	Ethernet TRD4+ Signal	10	TRD4-	Ethernet TRD4- Signal
11	GND	0V	12	GND	0V
13	USB-DP3	USB3 DP Signal	14	GPIOA7	GPIOA7
15	USB-DM3	USB3 DM Signal	16	I2C2-SDA	I2C2_SDA/GPIOE13
17	VDD_5V	5V Power Out	18	I2C2-SCL	I2C2_SCL/GPIOE12
19	VDD_5V	5V Power Out	20	VDD_3.3V	3.3V Power Outt

Note:

1. SYS_3.3V: 3.3V power output
2. VVDD_5V: 5V power input/output. When the external device’s power is greater than the MicroUSB's the external device is charging the board otherwise the board powers the external device. The input range is 4.7V ~ 5.6V
3. All pins are 3.3V, output current is 5mA
4. For more details refer to its schematic: NanoPi NEO Core2-1707-Schematic.pdf

3.2 Dimensional Diagram

For more details refer to the document:pcb in dxf format

4 Get Started

4.1 Essentials You Need

Before starting to use your NanoPi NEO Core2 get the following items ready

• NanoPi NEO Core2
• microSD Card/TF Card: Class 10 or Above, minimum 8GB SDHC
• microUSB power. A 5V/2A power is a must
• A Host computer running Ubuntu 16.04 64 bit system

4.2 TF Cards We Tested

To make your NanoPi NEO Core2 boot and run fast we highly recommend you use a Class10 8GB SDHC TF card or a better one. The following cards are what we used in all our test cases presented here:

• SanDisk TF 8G Class10 Micro/SD TF card:

• SanDisk TF128G MicroSDXC TF 128G Class10 48MB/S:

• 川宇 8G C10 High Speed class10 micro SD card:

4.3 Make an Installation TF Card

4.3.1 Get Image Files

Visit this link download link to download image files and the flashing utility:

Image Files:
nanopi-neo-core2_friendlycore-xenial_4.x.y_YYYYMMDD.img.zip	FriendlyCore (base on UbuntuCore) Image File, Kernel: Linux-4.x.y
nanopi-neo-core2_eflasher_4.x.y_YYYYMMDD.img.zip	eflasher Image File, Kernel: Linux-4.x.y
Flash Utility:
win32diskimager.rar	Windows utility for flashing Debian image. Under Linux users can use "dd"

4.3.2 Make Bootable TF Card

4.3.2.1 Make UbuntuCore with Qt Embedded Image Card

• Extract the image file and win32diskimager.rar files. Insert a TF card(at least 8G) into a Windows PC and run the win32diskimager utility as administrator. On the utility's main window select your TF card's drive, the wanted image file and click on "write" to start flashing the TF card.
• After flashing is done insert this TF card to your NanoPi NEO Core2 and connect the board to a 5V/2A power NEO Core2 will be automatically powered on. If the PWR LED is solid on and the STAT LED is flashing it indicates the system is being booted.
  

Note: this method applies to making a bootable TF card with Debian too.

4.3.3 Flash OS to eMMC

• Extract the image file and win32diskimager.rar files. Insert a TF card(at least 8G) into a Windows PC and run the win32diskimager utility as administrator. On the utility's main window select your TF card's drive, the wanted image file and click on "write" to start flashing the TF card.
• After flashing is done insert this TF card to your NanoPi NEO Core2 and connect the board to a 5V/2A power NEO Core2 will be automatically powered on. If the PWR LED is solid on and the STAT LED is flashing it indicates the system is being booted.
  
• Run the following commands in a terminal to flash OS to eMMC:

$ su root
$ eflasher

The password for "root" is "fa". Type a number and press "enter" to select an OS you want to flash and then type "yes" and press "enter" to start flashing:

After it is done power off the board and take out the TF card. Power on the board again and your board will boot from eMMC.

5 Mini Shield for NanoPi NEO Core/Core2

Here is a setup where we connect a NanoPi NEO Core to a Mini Shield for NanoPi NEO Core/Core2. Here is an introduction to Mini Shield for NanoPi NEO Core/Core2 Mini Shield
: Mini Shield for NanoPi NEO Core/Core2 和 Core2

6 Work with FriendlyCore

6.1 Introduction

FriendlyCore is a light Linux system without X-windows, based on ubuntu core, It uses the Qt-Embedded's GUI and is popular in industrial and enterprise applications.

Besides the regular Ubuntu Core's features FriendlyCore has the following additional features:

• it integrates Qt4.8;
• it integrates NetworkManager;
• it has bluez and Bluetooth related packages;
• it has alsa packages;
• it has npi-config;
• it has RPiGPIO, a Python GPIO module;
• it has some Python/C demo in /root/ directory;
• it enables 512M-swap partition;

6.2 System Login

• If your board is connected to an HDMI monitor you need to use a USB mouse and keyboard.
• If you want to do kernel development you need to use a serial communication board, ie a PSU-ONECOM board, which will

For example, NanoPi-M1：

You can use a USB to Serial conversion board too.
Make sure you use a 5V/2A power to power your board from its MicroUSB port:
For example, NanoPi-NEO2：

• FriendlyCore User Accounts:

Non-root User:

   User Name: pi
   Password: pi

Root:

   User Name: root
   Password: fa

The system is automatically logged in as "pi". You can do "sudo npi-config" to disable auto login.

• Update packages

$ sudo apt-get update

6.3 Configure System with npi-config

The npi-config is a commandline utility which can be used to initialize system configurations such as user password, system language, time zone, Hostname, SSH switch , Auto login and etc. Type the following command to run this utility.

$ sudo npi-config

Here is how npi-config's GUI looks like:

6.4 Develop Qt Application

Please refer to: How to Build and Install Qt Application for FriendlyELEC Boards

6.5 Setup Program to AutoRun

You can setup a program to autorun on system boot with npi-config:

sudo npi-config

Go to Boot Options -> Autologin -> Qt/Embedded, select Enable and reboot.

6.6 Extend TF Card's Section

When FriendlyCore is loaded the TF card's section will be automatically extended.You can check the section's size by running the following command:

$ df -h

6.7 WiFi

For either an SD WiFi or a USB WiFi you can connect it to your board in the same way. The APXX series WiFi chips are SD WiFi chips. By default FriendlyElec's system supports most popular USB WiFi modules. Here is a list of the USB WiFi modules we tested:

Index	Model
1	RTL8188CUS/8188EU 802.11n WLAN Adapter
2	RT2070 Wireless Adapter
3	RT2870/RT3070 Wireless Adapter
4	RTL8192CU Wireless Adapter
5	mi WiFi mt7601
6	5G USB WiFi RTL8821CU
7	5G USB WiFi RTL8812AU

You can use the NetworkManager utility to manage network. You can run "nmcli" in the commandline utility to start it. Here are the commands to start a WiFi connection:

• Change to root

$ su root

• Check device list

$ nmcli dev

Note: if the status of a device is "unmanaged" it means that device cannot be accessed by NetworkManager. To make it accessed you need to clear the settings under "/etc/network/interfaces" and reboot your system.

• Start WiFi

$ nmcli r wifi on

• Scan Surrounding WiFi Sources

$ nmcli dev wifi

• Connect to a WiFi Source

$ nmcli dev wifi connect "SSID" password "PASSWORD" ifname wlan0

The "SSID" and "PASSWORD" need to be replaced with your actual SSID and password.If you have multiple WiFi devices you need to specify the one you want to connect to a WiFi source with iface
If a connection succeeds it will be automatically setup on next system reboot.

For more details about NetworkManager refer to this link: Use NetworkManager to configure network settings

If your USB WiFi module doesn't work most likely your system doesn't have its driver. For a Debian system you can get a driver from Debian-WiFi and install it on your system. For a Ubuntu system you can install a driver by running the following commands:

$ apt-get install linux-firmware

In general all WiFi drivers are located at the "/lib/firmware" directory.

6.8 Ethernet Connection

If a board is connected to a network via Ethernet before it is powered on it will automatically obtain an IP with DHCP activated after it is powered up. If you want to set up a static IP refer to: Use NetworkManager to configure network settings。

6.9 WiringPi and Python Wrapper

• WiringNP: NanoPi NEO/NEO2/Air GPIO Programming with C
• RPi.GPIO : NanoPi NEO/NEO2/Air GPIO Programming with Python

6.10 Custom welcome message

The welcome message is printed from the script in this directory：

/etc/update-motd.d/

For example, to change the FriendlyELEC LOGO, you can change the file /etc/update-motd.d/10-header. For example, to change the LOGO to HELLO, you can change the following line：

TERM=linux toilet -f standard -F metal $BOARD_VENDOR

To:

TERM=linux toilet -f standard -F metal HELLO

6.11 Modify timezone

For exampe, change to Shanghai timezone:

sudo rm /etc/localtime
sudo ln -ls /usr/share/zoneinfo/Asia/Shanghai /etc/localtime

6.12 Set Audio Device

If your system has multiple audio devices such as HDMI-Audio, 3.5mm audio jack and I2S-Codec you can set system's default audio device by running the following commands.

• After your board is booted run the following commands to install alsa packages:

$ apt-get update
$ apt-get install libasound2
$ apt-get install alsa-base
$ apt-get install alsa-utils

• After installation is done you can list all the audio devices by running the following command. Here is a similar list you may see after you run the command:

$ aplay -l
card 0: HDMI
card 1: 3.5mm codec
card 2: I2S codec

"card 0" is HDMI-Audio, "card 1" is 3.5mm audio jack and "card 2" is I2S-Codec. You can set default audio device to HDMI-Audio by changing the "/etc/asound.conf" file as follows:

pcm.!default {
    type hw
    card 0
    device 0
}
 
ctl.!default {
    type hw
    card 0
}

If you change "card 0" to "card 1" the 3.5mm audio jack will be set to the default device.
Copy a .wav file to your board and test it by running the following command:

$ aplay /root/Music/test.wav

You will hear sounds from system's default audio device.
If you are using H3/H5/H2+ series board with mainline kernel, the easier way is using npi-config。

6.13 Connect to USB Camera(FA-CAM202)

The FA-CAM202 is a 200M USB camera. You can refer to <Connect DVP Camera (CAM500B) to Board> on how to connect a USB camera to a board.
You need to change the start.sh script and make sure it uses a correct /dev/videoX node. You can check your FA-CAM202's node by running the following commands:

$ apt-get install v4l-utils
$ v4l2-ctl -d /dev/video1 -D
Driver Info (not using libv4l2):
        Driver name   : uvcvideo
        Card type     : HC 3358+2100: HC 3358+2100
        Bus info      : usb-1c1b000.usb-1
	...

Information above indicates that /dev/video1 is the device node of the FA-CAM 202.

6.14 Check CPU's Working Temperature

You can get CPU's working temperature by running the following command:

$ cpu_freq
CPU0 online=1 temp=26581 governor=ondemand cur_freq=480000
CPU1 online=1 temp=26581 governor=ondemand cur_freq=480000
CPU2 online=1 temp=26581 governor=ondemand cur_freq=480000
CPU3 online=1 temp=26581 governor=ondemand cur_freq=480000

This message means there are currently four CPUs working. All of their working temperature is 26.5 degree in Celsius and each one's clock is 480MHz.

6.15 Test Watchdog

You can test watchdog by running the following commands:

$ cd /root/demo/watchdog/
$ gcc watchdog_demo.c -o watchdog_demo
$ ./watchdog_demo /dev/watchdog0 10
Set timeout: 10 seconds
Get timeout: 10 seconds
System will reboot in 10 second

System will reboot in 10 seconds.

6.16 Test Infrared Receiver

Note: Please Check your board if IR receiver exist.
By default the infrared function is disabled you can enable it by using the npi-config utility:

$ npi-config
    6 Advanced Options     Configure advanced settings
        A8 IR              Enable/Disable IR
            ir Enable/Disable ir[enabled]

Reboot your system and test its infrared function by running the following commands:

$ apt-get install ir-keytable
$ echo "+rc-5 +nec +rc-6 +jvc +sony +rc-5-sz +sanyo +sharp +mce_kbd +xmp" > /sys/class/rc/rc0/protocols   # Enable infrared
$ ir-keytable -t
Testing events. Please, press CTRL-C to abort.

"ir-keytable -t" is used to check whether the receiver receives infrared signals. You can use a remote control to send infrared signals to the receiver. If it works you will see similar messages as follows:

1522404275.767215: event type EV_MSC(0x04): scancode = 0xe0e43
1522404275.767215: event type EV_SYN(0x00).
1522404278.911267: event type EV_MSC(0x04): scancode = 0xe0e42
1522404278.911267: event type EV_SYN(0x00).

6.17 Read CHIP ID

As for Allwinner H2+/H3/H5/ SoCs each of these CPUs has an internal 16-btye CHIP ID which can be read by running the following commands in the Linux-4.14 kernel:

$ apt-get install bsdmainutils
$ hexdump /sys/bus/nvmem/devices/sunxi-sid0/nvmem 
0000000 8082 0447 0064 04c3 3650 ce0a 1e28 2202
0000010 0002 0000 0000 0000 0000 0000 0000 0000
0000020 0000 0000 0000 0000 0000 0000 0000 0000
0000030 0000 0008 0508 0000 0000 0000 0000 0000
0000040 0000 0000 0000 0000 0000 0000 0000 0000

"8082 0447 0064 04c3 3650 ce0a 1e28 2202" is the 16-byte CHIP ID.

6.18 Access GPIO Pins/Wirings with WiringNP

The wiringPi library was initially developed by Gordon Henderson in C. It contains libraries to access GPIO, I2C, SPI, UART, PWM and etc. The wiringPi library contains various libraries, header files and a commandline utility:gpio. The gpio utility can be used to read and write GPIO pins.
FriendlyElec integrated this utility in FriendlyCore system allowing users to easily access GPIO pins. For more details refer to WiringNP WiringNP

6.19 Run Qt Demo

Run the following command

$ sudo /opt/QtE-Demo/run.sh

Here is what you expect to observe. This is an open source Qt Demo:

6.20 How to install and use docker (for arm64 system)

6.20.1 How to Install Docker

Run the following commands：

sudo apt-get update
sudo apt-get install docker.io

6.20.2 Test Docker installation

Test that your installation works by running the simple docker image:

git clone https://github.com/friendlyarm/debian-jessie-arm-docker
cd debian-jessie-arm-docker
./rebuild-image.sh
./run.sh

6.21 Play & Record Audio

Core2's audio interface is populated to a 2.54mm pitch pin-header. Here is the pin description:

Pin#	Name	Description
1	MICIN1P	Microphone Positive Input
2	MICIN1N	Microphone Negative Input
3	LINEOUTR	LINE-OUT Right Channel Output
4	LINEOUTL	LINE-OUT Left Channel Output

Here is a hardware setup for connecting an audio device to a NanoPi NEO Core2:
耳麦标注
Make sure an audio device is connected to your NEO Core2 and you can play and record audio by running the following commands.
List audio device:

$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0

Both Allwinner H5 and H3 have a codec device which is recognized in the kernel as [H3 Audio Codec].

Play audio:

$ aplay /root/Music/test.wav -D plughw:0

Record audio:

$ arecord -f cd -d 5 test.wav

7 Make Your Own FriendlyCore

7.1 Use Mainline BSP

The NanoPi NEO Core2 works with a 64-bit Linux kernel and 64-bit UbuntuCore 16.04. For more details about how to use mainline u-boot and Linux-4.x.y refer to :Mainline U-boot & Linux

7.2 Use Allwinner's BSP

7.2.1 Preparations

Visit this link download link and enter the "sources/nanopi-h5-bsp" directory and download all the source code.Use the 7-zip utility to extract it and a lihee directory and an Android directory will be generated.You can check that by running the following command:

$ ls ./
android lichee

Or you can get it from our github:

$ git clone https://github.com/friendlyarm/h3_lichee.git lichee

Note: "lichee" is the project name named by Allwinner for its CPU's source code which contains the source code of U-boot, Linux kernel and various scripts.

7.2.2 Install Cross Compiler

Visit this site download link, enter the "toolchain" directory, download the cross compiler gcc-linaro-arm-4.6.3.tar.xz and gcc-linaro-aarch64.tar.xz and copy them to the "lichee/brandy/toochain/" directory.
The gcc-linaro-arm-4.6.3.tar.xz compiler is used to compile u-boot and gcc-linaro-aarch64.tar.xz is used to compile a Linux kernel.

7.2.3 Compile lichee Source Code

Compilation of the H5's BSP source code must be done under a PC running a 64-bit Linux.The following cases were tested on Ubuntu-14.04 LTS-64bit:

$ sudo apt-get install gawk git gnupg flex bison gperf build-essential \
zip curl libc6-dev libncurses5-dev:i386 x11proto-core-dev \
libx11-dev:i386 libreadline6-dev:i386 libgl1-mesa-glx:i386 \
libgl1-mesa-dev g++-multilib mingw32 tofrodos \
python-markdown libxml2-utils xsltproc zlib1g-dev:i386

Enter the lichee directory and un the following command to compile the whole package:

$ cd lichee/fa_tools
$ ./build.sh -b nanopi-neo2 -p linux -t all

After this compilation succeeds a u-boot, Linux kernel and kernel modules will be generated.
Note: the lichee directory contains a cross-compiler we have setup. When the build.sh script runs it will automatically call this cross-compiler.

Type the following command to update the U-boot on your TF card:

$ cd lichee/fa_tools/
$ ./fuse.sh -d /dev/sdX -p linux -t u-boot

Note: you need to replace "/dev/sdx" with the device name in your system.
The boot.img and kernel modules are under the "linux-3.10/output" directory. You can copy the new boot.img file to your TF card's boot partition.

7.3 Compile U-boot

Note:before you can compile u-boot individually you need to compile the whole lichee directory. You can compile u-boot individually by using the following command:

$ cd lichee/fa_tools/
$ ./build.sh -b nanopi-neo2 -p linux -t u-boot

Type the following command to update the U-boot on your TF card:

$ cd lichee/fa_tools/
$ ./fuse.sh -d /dev/sdX -p linux -t u-boot

Note: you need to replace "/dev/sdx" with the device name in your system.

7.4 Compile Linux Kernel

If you want to compile the Linux kernel run the following command:

$ cd lichee/fa_tools/
$ ./build.sh -b nanopi-neo2 -p linux -t kernel

After the compilation is done a uImage and its kernel modules will be generated under "linux-3.10/output".

7.5 Clean Source Code

$ cd lichee/fa_tools/
$ ./build.sh -b nanopi-neo2 -p linux -t clean

8 Connect External Modules to NEO Core2

8.1 Connect Python Programmable NanoHat OLED to NEO Core2

The NanoHat OLED module is a small and cute monochrome OLED module with low power consumption. It has three user buttons. We provide its driver's source code and a user friendly shell interface on which you can check system information and status.A customized aluminum case is made for it. You cannot miss this lovely utility! Here is a hardware setup:NanoHat OLED

8.2 Connect Python Programmable NanoHat Motor to NEO Core2

The NanoHat Motor module can drive four 5V PWM steering motors and four 12V DC motors or four 5V PWM steering motors and two 12V four-wire step motors.Here is a hardware setup: NanoHat Motor

8.3 Connect NanoHat PCM5102A to NEO Core2

The NanoHat PCM5102A module uses TI's DAC audio chip PCM5102A, a convenient and easy-to-use audio module for hobbyists. Here is a hardware setup:NanoHat PCM5102A

8.4 Connect Arduino Compatible UNO Dock to NEO Core2

The UNO Dock module is an Arduino board compatible with Arduino UNO and works with Arduino programs.You can use Arduino IDE to run all Arduino programs on the Dock.It also exposes the NanoPi NEO Core2's pins.It converts 12V power input to 5V/2A output.You can search for various code samples from Ubuntu's ecosystem and run on the Dock. These features make it a powerful platform for IOT projects and cloud related applications. Here is a hardware setup:UNO Dock for NanoPi NEO v1.0
Matrix-UNO_Dock_NEO_Core2

8.5 Connect NanoHat Proto to NEO Core2

The NanoHat Proto is an expansion board which exposes NEO Core2's various pins.It has an onboard EEPROM for data storage.Here is a hardware setup:NanoHat Proto
Matrix - NanoHat Proto_nanopi_NEO_Core2

8.6 Connect Matrix - 2'8 SPI Key TFT to NanoPi NEO Core2

The Matrix-2'8_SPI_Key_TFT module is a 2.8" TFT LCD with resistive touch. It uses the ST7789S IC and XPT2046 resistive touch IC. It has SPI interface and three configurable user keys.Here is its wiki page Matrix - 2'8 SPI Key TFT

9 3D Printing Files for Housing

10 Resources

10.1 Datasheet & Schematic

• Schematic
  • NanoPi-NEO-Core2-1707-Schematic.pdf
• Dimensional diagram
  • NanoPi-NEO-Core2-1707 pcb in dxf format
• H5 datasheet Allwinner_H5_Datasheet_V1.0.pdf

11 Update Log

11.1 Dec-1-2017

• Released English version