CM3588 NAS Kit

From FriendlyELEC WiKi
Revision as of 07:47, 14 November 2023 by Yonganch (Talk | contribs) (→‎Introduction)

Jump to: navigation, search

查看中文

1 Introduction

Carrier Board Front
Carrier Board Back
  • CM3588 NAS SDK是基于CM3588核心板精心设计的底板，包含4个M.2 Key M PCIe3.0 x1座子，2个USB3.0 Type-A，一个支持DP的USB3.0 Type-C接口，两路HDMI OUT，一路HDMI IN，一路2.5Gbps以太网等高速接口。
  • 提供Android, Ubuntu, Debian, Buildroot，OpenMediaVault和OpenWrt等操作系统, 软件资源和生态非常丰富，非常适合中小型企业和初创公司做高端人脸识别，机器视觉，自动驾驶，深度计算分析等方面的人工智能产品快速原型及产品开发。

2 Hardware Spec

  • Core Board: CM3588 based on Rockchip RK3588 SoC
    • CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
    • GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
    • VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265 encoder
    • NPU: 6TOPs, supports INT4/INT8/INT16/FP16
    • RAM: 64-bit 4GB/8GB/16GB LPDDR4X at 2133MHz
    • Flash: 0GB/64GB eMMC, at HS400 mode
    • Codec: On-board ALC5616 Codec
    • Low power RTC (HYM8563TS)
  • 1 x microSD slot, support up to SDR104 mode
  • 1 x 2.5Gbps RJ45 Port
  • 1 x USB 3.0 Type-C DRP port, which supports DP display（up to 4Kp60）
  • 2 x USB 3.0 Type-A Ports
  • 1 x USB 2.0 Type-A Port
  • 4 x M.2 M-Key connector with PCIe 3.0 x1 for NVMe SSDs
  • 2 x HDMI outputs which is compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
    • one support displays up to 7680x4320@60Hz, another one support up to 4Kp60
  • 1 x HDMI input, up to 4Kp60
  • 1 x 4lane MIPI CSI ,compatible with MIPI V1.2
  • 1 x 4lane MIPI DSI, compatible with MIPI DPHY 2.0 or CPHY 1.1
  • 1 x stereo 3.5mm headphone output Jack ( 20mW/CH, THD+N <= -80dB, 16Ohm Load )
  • 1 x 2.0mm PH-2A connector for single-end microphone input
  • 1 x 40 Pins 2.54mm GPIO header
    • up to 2 x SPIs, 6 x UARTs, 1 x I2Cs, 8 x PWMs, 2x I2Ss, 28 x GPIOs
  • others:
    • 1 x 2-Pin 1.27/1.25mm RTC battery input connector
    • 1 x 38Khz IR receiver
    • 1 x 5V Fan connector
    • 1 x PWM buzzer
    • MASK button for eMMC update, reset button, Power button, recovery mode button, and 1 x User button
    • Debug UART, 3-Pin 2.54mm header, 3.3V level, 1500000bps
    • 4 x NVME SSD LEDs
  • Power supply: 12VDC input
  • PCB: 4 Layers, 160*116*1.6mm
  • Ambient Operating Temperature: 0℃ to 70℃

3 Diagram, Layout and Dimension

TODO

3.1 Layout

TODO

4 Get Started

Link to CM3588 Wiki Page Wiki Page

5 Schematic, PCB CAD File

Retrieved from "https://wiki.friendlyelec.com/wiki/index.php?title=CM3588_NAS_Kit&oldid=25320"