Difference between revisions of "CM3588 NAS Kit"

Latest revision as of 02:31, 18 September 2024

查看中文

1 Introduction

Carrier Board Front

Carrier Board Back

• The CM3588 NAS Kit is a carrier board designed based on the CM3588 core module. It includes 4x M.2 Key M PCIe 3.0 x1 slots, 2x USB3.0 Type-A ports, 1x USB3.0 Type-C interface with DP support, dual HDMI OUT ports and one HDMI IN port, and a 2.5Gbps Ethernet interface.

2 Hardware Spec

• CPU Board: CM3588 based on Rockchip RK3588 SoC
  • CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
  • GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
  • VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265 encoder
  • NPU: 6TOPs, supports INT4/INT8/INT16/FP16
  • RAM: 64-bit 4GB/8GB/16GB LPDDR4X at 2133MHz
  • Flash: 0GB/64GB eMMC, at HS400 mode
  • Codec: On-board ALC5616 Codec
  • Low power RTC (HYM8563TS)
• 1 x microSD slot, support up to SDR104 mode
• 1 x 2.5Gbps RJ45 Port
• 1 x USB 3.0 Type-C DRP port, which supports DP display（up to 4Kp60）
• 2 x USB 3.0 Type-A Ports
• 1 x USB 2.0 Type-A Port
• 4 x M.2 M-Key connector with PCIe 3.0 x1 for NVMe SSDs
• 2 x HDMI outputs which is compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
  • one support displays up to 7680x4320@60Hz, another one support up to 4Kp60
• 1 x HDMI input, up to 4Kp60
• 1 x 4lane MIPI CSI ,compatible with MIPI V1.2
• 1 x 4lane MIPI DSI, compatible with MIPI DPHY 2.0 or CPHY 1.1
• 1 x stereo 3.5mm headphone output Jack ( 20mW/CH, THD+N <= -80dB, 16Ohm Load )
• 1 x 2.0mm PH-2A connector for single-end microphone input
• 1 x 40 Pins 2.54mm GPIO header
  • up to 2 x SPIs, 6 x UARTs, 1 x I2Cs, 8 x PWMs, 2x I2Ss, 28 x GPIOs
• others:
  • 1 x 2-Pin 1.27/1.25mm RTC battery input connector
  • 1 x 38Khz IR receiver
  • 1 x 5V Fan connector
  • 1 x PWM buzzer
  • MASK button for eMMC update, reset button, Power button, recovery mode button, and 1 x User button
  • Debug UART, 3-Pin 2.54mm header, 3.3V level, 1500000bps
  • 4 x NVME SSD LEDs
• Power supply: 12VDC input
• PCB: 4 Layers, 160*116*1.5mm
• Ambient Operating Temperature: 0℃ to 70℃

3 Diagram, Layout and Dimension

4 Power In

• DC-Jack: 5.5*2.1mm
• Green connector: DB2EVC-3.5-2P-GN or compatible part
• 15V Max

5 Get Started

Link to CM3588 Wiki Page

6 Schematic, PCB CAD File

• CM3588 Schematic: https://wiki.friendlyelec.com/wiki/images/0/00/CM3588_2309_SCH.PDF
• CM3588 PCB CAD File：https://wiki.friendlyelec.com/wiki/images/f/f5/CM3588_2309_DXF.zip
• CM3588 NAS SDK Schematic: https://wiki.friendlyelec.com/wiki/images/1/15/CM3588_NAS_SDK_2309_SCH.PDF
• CM3588 NAS SDK PCB CAD File: https://wiki.friendlyelec.com/wiki/images/f/fe/CM3588_NAS_SDK_2309_DXF.zip
• CM3588 NAS SDK PCB layout PDF File: https://wiki.friendlyelec.com/wiki/images/2/2c/CM3588_NAS_SDK_2309_PCB_Layout.pdf
• CM3588 NAS SDK 3D File: https://wiki.friendlyelec.com/wiki/images/2/21/CM3588_NAS_SDK_2309_3D_stp.zip