Difference between revisions of "NanoPi K1 Plus"

Revision as of 10:32, 5 July 2018

查看中文

1 Introduction

• The NanoPi K1 Plus uses the Allwinner 64-bit quad-core Cortex™-A53 H5 SoC. It can run either a 64-bit OS or a 32-bit OS. It has NEON multi-media engine and a hex-core Mali450 GPU. It supports various video formats and has strong HD encoding/decoding capabilities.
• The NanoPi K1 Plus has 2GB DDR3 RAM, onboard WiFi, DVP camera interface, Gbps Ethernet, USB, HDMI, infrared remote control, 3.5mm audio jack, I2S and etc. It can boot from a TF card and supports an external eMMC module.
• The NanoPi K1 Plus has the same dimension as RPi 3. Its 40-Pin GPIO pin-header is compatible with RPi 3's GPIO pin-header. It works with any RPi housing.
• A Ubuntu Core image and an Armbian image are ready for the NanoPi K1 Plus.

2 Hardware Spec

• CPU: Allwinner H5, Quad-core 64-bit high-performance Cortex™-A53
• GPU: Hexa-core Mali450
• DDR3 RAM: 2GB
• Ethernet: 10/100/1000M Ethernet using RTL8211E IC
• Wireless: 802.11 b/g/n and onboard PCB antenna
• Infrared: Onboard infrared receiver
• Audio: 3.5mm audio jack/Via HDMI
• Mic: onboard microphone
• eMMC: onboard eMMC interface
• I2S: onboard I2S interface(7Pin, 2.54mm pin-header)
• MicroSD Slot: MicroSD card slot
• USB Host: 3 x USB 2.0 Host, type A port
• DVP Camera interface: 24-Pin, 0.5mm pitch FPC seat
• MicroUSB: 1 x USB 2.0, OTG, for power input and data transmission
• HDMI: HDMI Type-A port. It supports 4K@30fps dsplay
• Video Output: HDMI 1.4. It supports 4K@30fps display, CVBS
• GPIO Pin-header: 40 Pin,2.54mm pitch pin-header containing I2C, GPIO, UART, PWM, SPDIF, SPI and etc
• Serial Debug Port: 4Pin, 2.5mm pitch pin-header
• Button: 1 x GPIO button(user configurable)
• LED: 1 x power LED and 1 x status LED
• Power Interface: MicroUSB
• PCB Size:56 x 85mm, 6-layer, ENIG
• Power: DC 5V/2A

3 Diagram, Layout and Dimension

3.1 Layout

NanoPi-K1-Plus Interface Layout

• GPIO Pin Spec

Pin#	Name	Linux gpio	Pin#	Name	Linux gpio
1	SYS_3.3V		2	VDD_5V
3	I2C0_SDA / GPIOA12		4	VDD_5V
5	I2C0_SCL / GPIOA11		6	GND
7	GPIOG11	203	8	UART1_TX / GPIOG6	198
9	GND		10	UART1_RX / GPIOG7	199
11	UART2_TX / GPIOA0	0	12	GPIOA6	6
13	UART2_RTS / GPIOA2	2	14	GND
15	UART2_CTS / GPIOA3	3	16	UART1_RTS / GPIOG8	200
17	SYS_3.3V		18	UART1_CTS / GPIOG9	201
19	SPI0_MOSI / GPIOC0	64	20	GND
21	SPI0_MISO / GPIOC1	65	22	UART2_RX / GPIOA1	1
23	SPI0_CLK / GPIOC2	66	24	SPI0_CS / GPIOC3	67
25	GND		26	SPDIF-OUT / GPIOA17	17
27	I2C1_SDA / GPIOA19 / PCM0_CLK / I2S0_BCK	19	28	I2C1_SCL / GPIOA18 / PCM0_SYNC / I2S0_LRCK	18
29	GPIOA20 / PCM0_DOUT / I2S0_SDOUT	20	30	GND
31	GPIOA21 / PCM0_DIN/ I2S0_SDIN	21	32	GPIOA7	7
33	GPIOA8	8	34	GND
35	UART3_CTS / SPI1_MISO / GPIOA16	16	36	UART3_TX / SPI1_CS / GPIOA13	13
37	GPIOA9	9	38	UART3_RTS / SPI1_MOSI / GPIOA15	15
39	GND		40	UART3_RX / SPI1_CLK / GPIOA14	14

• eMMC Connector Pin Spec

Pin#	Name	Pin#	Name
1	eMMC_D0	2	eMMC_D1
3	eMMC_D2	4	eMMC_D3
5	eMMC_D4	6	eMMC_D5
7	eMMC_D6	8	eMMC_D7
9	eMMC_DS	10	GND
11	eMMC_CMD	12	eMMC_CLK
13	NC	14	GND
15	NC	16	1.8V OUT
17	eMMC_RST	18	3.3V OUT
19	GPIOY_5	20	GND

• Debug Port（UART0）

Pin#	Name
1	GND
2	VDD_5V
3	UART_TX
4	UART_RX

• 7Pin I2S Pin Spec

Pin#	Name
1	GND
2	SYS_3.3V
3	I2S0_BCK
4	I2S0_LRCK
5	I2S0_SDOUT
6	I2S0_SDIN
7	I2S_MCLK

Notes

1. SYS_3.3V: 3.3V power output
2. VDD_5V: 5V power input/output. Input power range: 4.7～5.6V
3. All signal pins are 3.3V
4. For more details refer to :Schematic_NanoPi-K1_Plus-1712_20171214.pdf

3.2 Board Dimension

For more details refer to:NanoPi_K1_Plus_V1.0_1712_dxf.zip

4 Get Started

4.1 Essentials You Need

Before starting to use your NanoPi K1 Plus get the following items ready

• NanoPi K1 Plus
• MicroSD/TF Card: Class 10 or Above, minimum 8GB SDHC
• A DC 5V/2A power cord with MicroUSB port is a must
• HDMI monitor
• USB keyboard, mouse and possible a USB hub(or a TTL to serial board)
• A host computer running Ubuntu 16.04 64 bit system

4.2 TF Cards We Tested

The following cards are what we used in all our test cases presented here:

• SanDisk TF 8G Class10 Micro/SD TF card:

• SanDisk TF128G MicroSDXC TF 128G Class10 48MB/S:

• 川宇 8G C10 High Speed class10 micro SD card:

4.3 Install OS

4.3.1 Download Image Files

Get the following files from here download link to download image files(under the "official-ROMs" directory) and the flashing utility(under the "tools" directory):

Image Files:
nanopi-k1-plus_friendlycore-xenial_4.x.y_YYYYMMDD.img.zip	FriendlyCore(based on UbuntuCore), kernel:Linux-4.x
nanopi-k1-plus_ubuntu-tft_4.x.y_YYYYMMDD.img.zip	FriendlyElec's 2.8'TFT supported image file, kernel: Linux-4.x.y Matrix - 2'8 SPI Key TFT
nanopi-k1-plus_eflasher_4.x.y_YYYYMMDD.img.zip	eflasher image file, kernel: Linux-4.x
DietPi_vX.Y_NanoPiK1Plus-ARMv8-Stretch-YYYYMMDD.img.7z	DietPi image file，kernel: Linux-4.x，unofficial ROM, refer to Dietpi
Flash Utility:
win32diskimager.rar	Windows utility. Under Linux users can use "dd"

4.3.2 Linux

4.3.2.1 Flash to TF

• FriendlyCore / Debian / Ubuntu / OpenWrt / DietPi are all based on a same Linux distribution and their installation methods are the same.
• Extract the Linux image and win32diskimager.rar files. Insert a TF card(at least 8G) into a Windows PC and run the win32diskimager utility as administrator. On the utility's main window select your TF card's drive, the wanted image file and click on "write" to start flashing the TF card.

Take "nanopi-k1-plus_sd_friendlycore-xenial_4.14_arm64_YYYYMMDD.img" as an example here is the installation window. Other image files are installed on the similar window:

After it is installed you will see the following window:

• Insert this card into your board's BOOT slot and power on (with a 5V/2A power source). If the PWR LED is on and the STAT LED is blinking this indicates your board has successfully booted.
  

4.3.2.2 Flash to eMMC

4.3.2.2.1 Flash OS with eflasher Utility

• For more details about eflasher refer to the wiki link: EFlasher。
• Extract the eflasher Image and win32diskimager.rar files. Insert a TF card(at least 4G) into a Windows PC and run the win32diskimager utility as administrator. On the utility's main window select your TF card's drive, the wanted image file and click on "write" to start flashing the TF card.
• Insert this card into your board's BOOT slot and power on (with a 5V/2A power source). If the green LED is on and the blue LED is blinking this indicates your board has successfully booted.
• If your board doesn't support HDMI or no monitor is connected you can select an OS by running the following command:

$ su root
$ eflasher

The password for "root" is "fa".

We take "nanopi-k1-plus_eflasher_friendlycore-xenial_4.14_arm64_YYYYMMDD.img" as an example. After you run the "eflasher" command you will see the following messages:

Type "1", select writing friendlycore system to eMMC you will see the following messages:

Type "yes" to start installation:

After it is done power off the system, take off the TF card, power on again your system will be booted from eMMC.

• If you want to flash other system to eMMC you can download the whole images-for-eflasher directory and extract the package under that directory to the FRIENDLYARM partition of an installation SD card.
  

4.3.2.2.2 Flash OS to eMMC on PC

• An OS image for eMMC is the same as the one for an SD card. Extract an image package and flash utility. Insert an eMMC module(in a MicroSD to eMMC adapter) to a Windows PC. Run the win32diskimager utility as administrator. On the win32diskimager's main window select your MicroSD to eMMC adapter's drive, a wanted OS image and click "Write" to start flashing.

• After flash is done take out the MicroSD to eMMC adapter. Take the eMMC module off the adapter, insert this module to the board's eMMC slot and power up the board. If the PWR LED is solid on and the STAT LED is flashing it means your board has been successfully booted.
  
• When both an SD card and an eMMC module are connected to a board the board will be booted from the SD card first and if that fails it will be booted from eMMC.

4.3.3 Android

4.3.3.1 Flash to TF

Note:before make a MicroSD card to an Android image card you need to format this card.

• On a Windows PC run the HDDLLF.4.40 utility as administrator. Insert a TF card(at least 8G) into this PC and format it. After formatting is done take out the TF card, insert it into the PC again and format it with Windows internal format utility to format it to FAT32. After this formatting is done take out the card.
• Extract the the Android image and PhoenixCard_V310.rar . Insert the TF card you made in the previous step into a Windows PC and run the PhoenixCard_V310 utility as administrator. On the utility's main window select your TF card's drive, the wanted image file and click on "write" to start flashing the TF card.

(In the screenshot an Android image file for the NanoPi M1 Plus was selected. You need to select a correct image file for your board.)

• Insert this card into your board' BOOT slot and power on (with a 5V/2A power source). If the green LED is on and the blue LED is blinking this indicates your board has successfully booted.
  

4.3.3.2 Flash to eMMC

4.3.3.2.1 Install Android to eMMC from TF Card

• Extract an Android image file and the flashing utility PhoenixCard_V310.rar, insert a TF card(at least 8G) to a windows PC and run PhoenixCard as administrator. On the PhoenixCard Window select your TF card's device and your wanted Android image file, set the mode to "卡量产(factory production)" and click on "烧录(Flash)" to start flashing the Android image to TF card.

(In the screenshot an Android image file for the NanoPi M1 Plus was selected. You need to select a correct image file for your board.)

• After flashing is done, the TF card has the ability to burn the Android system to eMMC. Take out the TF card and insert it to your board's TF card slot. Connect your board to an HDMI monitor, power on your board(note:you need a 5V/2A power adapter) and you will see a green process bar on the HDMI monitor. After flashing is done take out the TF card and reboot your board and it will be rebooted from eMMC.

5 Work with FriendlyCore

5.1 Introduction

FriendlyCore is a light Linux system without X-windows, based on ubuntu core, It uses the Qt-Embedded's GUI and is popular in industrial and enterprise applications.

Besides the regular Ubuntu Core's features FriendlyCore has the following additional features:

• it integrates Qt4.8;
• it integrates NetworkManager;
• it has bluez and Bluetooth related packages;
• it has alsa packages;
• it has npi-config;
• it has RPiGPIO, a Python GPIO module;
• it has some Python/C demo in /root/ directory;
• it enables 512M-swap partition;

5.2 System Login

• If your board is connected to an HDMI monitor you need to use a USB mouse and keyboard.
• If you want to do kernel development you need to use a serial communication board, ie a PSU-ONECOM board, which will

For example, NanoPi-M1：

You can use a USB to Serial conversion board too.
Make sure you use a 5V/2A power to power your board from its MicroUSB port:
For example, NanoPi-NEO2：

• FriendlyCore User Accounts:

Non-root User:

   User Name: pi
   Password: pi

Root:

   User Name: root
   Password: fa

The system is automatically logged in as "pi". You can do "sudo npi-config" to disable auto login.

• Update packages

$ sudo apt-get update

5.3 Configure System with npi-config

The npi-config is a commandline utility which can be used to initialize system configurations such as user password, system language, time zone, Hostname, SSH switch , Auto login and etc. Type the following command to run this utility.

$ sudo npi-config

Here is how npi-config's GUI looks like:

5.4 Develop Qt Application

Please refer to: How to Build and Install Qt Application for FriendlyELEC Boards

5.5 Setup Program to AutoRun

You can setup a program to autorun on system boot with npi-config:

sudo npi-config

Go to Boot Options -> Autologin -> Qt/Embedded, select Enable and reboot.

5.6 Extend TF Card's Section

When FriendlyCore is loaded the TF card's section will be automatically extended.You can check the section's size by running the following command:

$ df -h

5.7 Transfer files using Bluetooth

Take the example of transferring files to the mobile phone. First, set your mobile phone Bluetooth to detectable status, then execute the following command to start Bluetooth search.：

hcitool scan

Search results look like：

Scanning ...
    2C:8A:72:1D:46:02   HTC6525LVW

This means that a mobile phone named HTC6525LVW is searched. We write down the MAC address in front of the phone name, and then use the sdptool command to view the Bluetooth service supported by the phone：

sdptool browser 2C:8A:72:1D:46:02

Note: Please replace the MAC address in the above command with the actual Bluetooth MAC address of the mobile phone.
This command will detail the protocols supported by Bluetooth for mobile phones. What we need to care about is a file transfer service called OBEX Object Push. Take the HTC6525LVW mobile phone as an example. The results are as follows：

Service Name: OBEX Object Push
Service RecHandle: 0x1000b
Service Class ID List:
  "OBEX Object Push" (0x1105)
Protocol Descriptor List:
  "L2CAP" (0x0100)
  "RFCOMM" (0x0003)
    Channel: 12
  "OBEX" (0x0008)
Profile Descriptor List:
  "OBEX Object Push" (0x1105)
    Version: 0x0100

As can be seen from the above information, the channel used by the OBEX Object Push service of this mobile phone is 12, we need to pass it to the obexftp command, and finally the command to initiate the file transfer request is as follows：

obexftp --nopath --noconn --uuid none --bluetooth -b 2C:8A:72:1D:46:02 -B 12 -put example.jpg

Note: Please replace the MAC address, channel and file name in the above command with the actual one.

After executing the above commands, please pay attention to the screen of the mobile phone. The mobile phone will pop up a prompt for pairing and receiving files. After confirming, the file transfer will start.

Bluetooth FAQ：
1) Bluetooth device not found on the development board, try to open Bluetooth with the following command：

rfkill unblock 0

2) Prompt can not find the relevant command, you can try to install related software with the following command：

apt-get install bluetooth bluez obexftp openobex-apps python-gobject ussp-push

5.8 WiFi

For either an SD WiFi or a USB WiFi you can connect it to your board in the same way. The APXX series WiFi chips are SD WiFi chips. By default FriendlyElec's system supports most popular USB WiFi modules. Here is a list of the USB WiFi modules we tested:

Index	Model
1	RTL8188CUS/8188EU 802.11n WLAN Adapter
2	RT2070 Wireless Adapter
3	RT2870/RT3070 Wireless Adapter
4	RTL8192CU Wireless Adapter
5	mi WiFi mt7601
6	5G USB WiFi RTL8821CU
7	5G USB WiFi RTL8812AU

You can use the NetworkManager utility to manage network. You can run "nmcli" in the commandline utility to start it. Here are the commands to start a WiFi connection:

• Change to root

$ su root

• Check device list

$ nmcli dev

Note: if the status of a device is "unmanaged" it means that device cannot be accessed by NetworkManager. To make it accessed you need to clear the settings under "/etc/network/interfaces" and reboot your system.

• Start WiFi

$ nmcli r wifi on

• Scan Surrounding WiFi Sources

$ nmcli dev wifi

• Connect to a WiFi Source

$ nmcli dev wifi connect "SSID" password "PASSWORD" ifname wlan0

The "SSID" and "PASSWORD" need to be replaced with your actual SSID and password.If you have multiple WiFi devices you need to specify the one you want to connect to a WiFi source with iface
If a connection succeeds it will be automatically setup on next system reboot.

For more details about NetworkManager refer to this link: Use NetworkManager to configure network settings

If your USB WiFi module doesn't work most likely your system doesn't have its driver. For a Debian system you can get a driver from Debian-WiFi and install it on your system. For a Ubuntu system you can install a driver by running the following commands:

$ apt-get install linux-firmware

In general all WiFi drivers are located at the "/lib/firmware" directory.

5.9 Ethernet Connection

If a board is connected to a network via Ethernet before it is powered on it will automatically obtain an IP with DHCP activated after it is powered up. If you want to set up a static IP refer to: Use NetworkManager to configure network settings。

5.10 WiringPi and Python Wrapper

• WiringNP: NanoPi NEO/NEO2/Air GPIO Programming with C
• RPi.GPIO : NanoPi NEO/NEO2/Air GPIO Programming with Python

5.11 Custom welcome message

The welcome message is printed from the script in this directory：

/etc/update-motd.d/

For example, to change the FriendlyELEC LOGO, you can change the file /etc/update-motd.d/10-header. For example, to change the LOGO to HELLO, you can change the following line：

TERM=linux toilet -f standard -F metal $BOARD_VENDOR

To:

TERM=linux toilet -f standard -F metal HELLO

5.12 Modify timezone

For exampe, change to Shanghai timezone:

sudo rm /etc/localtime
sudo ln -ls /usr/share/zoneinfo/Asia/Shanghai /etc/localtime

5.13 Set Audio Device

If your system has multiple audio devices such as HDMI-Audio, 3.5mm audio jack and I2S-Codec you can set system's default audio device by running the following commands.

• After your board is booted run the following commands to install alsa packages:

$ apt-get update
$ apt-get install libasound2
$ apt-get install alsa-base
$ apt-get install alsa-utils

• After installation is done you can list all the audio devices by running the following command. Here is a similar list you may see after you run the command:

$ aplay -l
card 0: HDMI
card 1: 3.5mm codec
card 2: I2S codec

"card 0" is HDMI-Audio, "card 1" is 3.5mm audio jack and "card 2" is I2S-Codec. You can set default audio device to HDMI-Audio by changing the "/etc/asound.conf" file as follows:

pcm.!default {
    type hw
    card 0
    device 0
}
 
ctl.!default {
    type hw
    card 0
}

If you change "card 0" to "card 1" the 3.5mm audio jack will be set to the default device.
Copy a .wav file to your board and test it by running the following command:

$ aplay /root/Music/test.wav

You will hear sounds from system's default audio device.
If you are using H3/H5/H2+ series board with mainline kernel, the easier way is using npi-config。

5.14 Connect to DVP Camera CAM500B

For NanoPi-K1-Plus the CAM500B can work with Linux-4.14 Kernel.
The CAM500B camera module is a 5M-pixel camera with DVP interface. For more tech details about it you can refer to Matrix - CAM500B.

connect your board to camera module. Then boot OS, connect your board to a network, log into the board as root and run "mjpg-streamer":

$ cd /root/C/mjpg-streamer
$ make
$ ./start.sh

You need to change the start.sh script and make sure it uses a correct /dev/videoX node. You can check your camera's node by running the following commands:

$ apt-get install v4l-utils
$ v4l2-ctl -d /dev/video0 -D
Driver Info (not using libv4l2):
        Driver name   : sun6i-video
        Card type     : sun6i-csi
        Bus info      : platform:camera
        Driver version: 4.14.0
	...

The above messages indicate that "/dev/video0" is camera's device node.The mjpg-streamer application is an open source video steam server. After it is successfully started the following messages will be popped up:

 
$ ./start.sh
 i: Using V4L2 device.: /dev/video0
 i: Desired Resolution: 1280 x 720
 i: Frames Per Second.: 30
 i: Format............: YUV
 i: JPEG Quality......: 90
 o: www-folder-path...: ./www/
 o: HTTP TCP port.....: 8080
 o: username:password.: disabled
 o: commands..........: enabled

start.sh runs the following two commands:

export LD_LIBRARY_PATH="$(pwd)"
./mjpg_streamer -i "./input_uvc.so -d /dev/video0 -y 1 -r 1280x720 -f 30 -q 90 -n -fb 0" -o "./output_http.so -w ./www"

Here are some details for mjpg_streamer's major options:
-i: input device. For example "input_uvc.so" means it takes input from a camera;
-o: output device. For example "output_http.so" means the it transmits data via http;
-d: input device's subparameter. It defines a camera's device node;
-y: input device's subparameter. It defines a camera's data format: 1:yuyv, 2:yvyu, 3:uyvy 4:vyuy. If this option isn't defined MJPEG will be set as the data format;
-r: input device's subparameter. It defines a camera's resolution;
-f: input device's subparameter. It defines a camera's fps. But whether this fps is supported depends on its driver;
-q: input device's subparameter. It defines the quality of an image generated by libjpeg soft-encoding;
-n: input device's subparameter. It disables the dynctrls function;
-fb: input device's subparameter. It specifies whether an input image is displayed at "/dev/fbX";
-w: output device's subparameter. It defines a directory to hold web pages;

In our case the board's IP address was 192.168.1.230. We typed 192.168.1.230:8080 in a browser and were able to view the images taken from the camera's. Here is what you would expect to observe:

The mjpg-streamer utility uses libjpeg to software-encode steam data. The Linux-4.14 based ROM currently doesn't support hardware-encoding. If you use a H3 boards with Linux-3.4 based ROM you can use the ffmpeg utility to hardware-encode stream data and this can greatly release CPU's resources and speed up encoding:

$ ffmpeg -t 30 -f v4l2 -channel 0 -video_size 1280x720 -i /dev/video0 -pix_fmt nv12 -r 30 \
        -b:v 64k -c:v cedrus264 test.mp4

By default it records a 30-second video. Typing "q" stops video recording. After recording is stopped a test.mp4 file will be generated.

5.15 Connect to USB Camera(FA-CAM202)

The FA-CAM202 is a 200M USB camera. You can refer to <Connect DVP Camera (CAM500B) to Board> on how to connect a USB camera to a board.
You need to change the start.sh script and make sure it uses a correct /dev/videoX node. You can check your FA-CAM202's node by running the following commands:

$ apt-get install v4l-utils
$ v4l2-ctl -d /dev/video1 -D
Driver Info (not using libv4l2):
        Driver name   : uvcvideo
        Card type     : HC 3358+2100: HC 3358+2100
        Bus info      : usb-1c1b000.usb-1
	...

Information above indicates that /dev/video1 is the device node of the FA-CAM 202.

5.16 Check CPU's Working Temperature

You can get CPU's working temperature by running the following command:

$ cpu_freq
CPU0 online=1 temp=26581 governor=ondemand cur_freq=480000
CPU1 online=1 temp=26581 governor=ondemand cur_freq=480000
CPU2 online=1 temp=26581 governor=ondemand cur_freq=480000
CPU3 online=1 temp=26581 governor=ondemand cur_freq=480000

This message means there are currently four CPUs working. All of their working temperature is 26.5 degree in Celsius and each one's clock is 480MHz.

5.17 Test Watchdog

You can test watchdog by running the following commands:

$ cd /root/demo/watchdog/
$ gcc watchdog_demo.c -o watchdog_demo
$ ./watchdog_demo /dev/watchdog0 10
Set timeout: 10 seconds
Get timeout: 10 seconds
System will reboot in 10 second

System will reboot in 10 seconds.

5.18 Test Infrared Receiver

Note: Please Check your board if IR receiver exist.
By default the infrared function is disabled you can enable it by using the npi-config utility:

$ npi-config
    6 Advanced Options     Configure advanced settings
        A8 IR              Enable/Disable IR
            ir Enable/Disable ir[enabled]

Reboot your system and test its infrared function by running the following commands:

$ apt-get install ir-keytable
$ echo "+rc-5 +nec +rc-6 +jvc +sony +rc-5-sz +sanyo +sharp +mce_kbd +xmp" > /sys/class/rc/rc0/protocols   # Enable infrared
$ ir-keytable -t
Testing events. Please, press CTRL-C to abort.

"ir-keytable -t" is used to check whether the receiver receives infrared signals. You can use a remote control to send infrared signals to the receiver. If it works you will see similar messages as follows:

1522404275.767215: event type EV_MSC(0x04): scancode = 0xe0e43
1522404275.767215: event type EV_SYN(0x00).
1522404278.911267: event type EV_MSC(0x04): scancode = 0xe0e42
1522404278.911267: event type EV_SYN(0x00).

5.19 Read CHIP ID

As for Allwinner H2+/H3/H5/ SoCs each of these CPUs has an internal 16-btye CHIP ID which can be read by running the following commands in the Linux-4.14 kernel:

$ apt-get install bsdmainutils
$ hexdump /sys/bus/nvmem/devices/sunxi-sid0/nvmem 
0000000 8082 0447 0064 04c3 3650 ce0a 1e28 2202
0000010 0002 0000 0000 0000 0000 0000 0000 0000
0000020 0000 0000 0000 0000 0000 0000 0000 0000
0000030 0000 0008 0508 0000 0000 0000 0000 0000
0000040 0000 0000 0000 0000 0000 0000 0000 0000

"8082 0447 0064 04c3 3650 ce0a 1e28 2202" is the 16-byte CHIP ID.

5.20 Access GPIO Pins/Wirings with WiringNP

The wiringPi library was initially developed by Gordon Henderson in C. It contains libraries to access GPIO, I2C, SPI, UART, PWM and etc. The wiringPi library contains various libraries, header files and a commandline utility:gpio. The gpio utility can be used to read and write GPIO pins.
FriendlyElec integrated this utility in FriendlyCore system allowing users to easily access GPIO pins. For more details refer to WiringNP WiringNP

5.21 Run Qt Demo

Run the following command

$ sudo /opt/QtE-Demo/run.sh

Here is what you expect to observe. This is an open source Qt Demo:

5.22 How to install and use docker (for arm64 system)

5.22.1 How to Install Docker

Run the following commands：

sudo apt-get update
sudo apt-get install docker.io

5.22.2 Test Docker installation

Test that your installation works by running the simple docker image:

git clone https://github.com/friendlyarm/debian-jessie-arm-docker
cd debian-jessie-arm-docker
./rebuild-image.sh
./run.sh

5.23 Play & Record Audio

You can play and record audio by running the following commands
Check audio devices:

$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0

Both Allwinner H5 and H3 have an internal codec which is recognized as [H3 Audio Codec]. You need to use the actual device name that your [H3 Audio Codec] device is recognized as in your system.

Play Audio:

$ aplay /root/Music/test.wav -D plughw:0

Parameter "-D plughw:0" means the "card 0" device is used to play the audio file. You need to choose a device from the list obtained by running "aplay -l".
Record Audio:

$ arecord -f cd -d 5 test.wav

6 Compile FriendlyCore Source Code

6.1 Use Mainline BSP

K1 Plus now works with a 64-bit Linux kernel and a 64-bit Ubuntu Core 16.04 system. For more details on how to use a mainline U-boot and Linux-4.x.y refer to:Mainline U-boot & Linux

7 Work with External Modules

7.1 Matrix - 2'8 SPI Key TFT LCD Module

The Matrix-2'8_SPI_Key_TFT LCD module is a 2.8' TFT LCD module with resistive touch. It uses the ST7789S IC and XPT2046 resistive touch IC. The LCD's resolution is 240 * 320. Its interface is SPI. The module has three independent buttons which are user-configurable. For more details refer to:Matrix - 2'8 SPI Key TFT

8 3D Printed Housing

9 Resources

9.1 Datasheet and Schematics

• Schematic: Schematic_NanoPi-K1_Plus-1712_20171214.pdf
• Dimensions: Dimensions_NanoPi_K1_Plus-V1.0-1712_pcb(dxf).rar
• H5 Datasheet: Allwinner_H5_Datasheet_V1.0.pdf

10 Update Log

10.1 April-19-2018

• Released English Version