SOM-4418

From FriendlyELEC WiKi
Revision as of 08:44, 1 July 2020 by Yonganch (Talk | contribs)

Jump to: navigation, search

查看中文

1 Introduction

Overview
Front
Back

2 Hardware Spec

  • SoC:Samsung S5P4418 Quad Core Cortex-A9 with dynamic frequency scaling up to 1.4G Hz
  • PMU Power Management: Implemented by an MCU, support solftware power-off, and RTC alarm power-on functions
  • System Memory:1GB 32bit DDR3 RAM
  • eMMC:8GB
  • Ethernet:Gbps Ethernet Port (RTL8211E) with unique MAC, support WOL(Wake On Lan)
  • Video Input: MIPI-CSI
  • Video Output: HDMI / LVDS / LCD
  • Audio: Build in Codec, 2-Chanel headphone output, one Microphone input
  • USB: 4 x USB 2.0 Host, 1 x USB 2.0 OTG
  • GPIO: 13 x GPIOs, 3 x I2Cs, 1 x SPI, 5 x UARTs, 3 x PWMs, 2 x SDIOs
  • LED: 1 x power LED , 1 x SYS LED
  • Other Resource: 1 x onboard thermistor
  • Power: DC 5V/1A
  • Heat Sink: Aluminum heat sink
  • PCB: Six Layer, ENIG
  • PCB Dimension: 67.7 mm x 40 mm
  • Working Temperature: -40℃ to 70℃

3 Software Features

4 Diagram, Layout and Dimension

4.1 Layout

File:SOM-4418-IF.png
SOM-4418 Layout
  • 204 Pin Spec
    • Socket Type:0.6mm Pitch 204-Pin Standard Type DDR3 SODIMM Socket
Pin# Name Description Pin# Name Description
1 VDD_5V 4.7~5.5V Power Suply input 2 VDD_5V 4.7~5.5V Power Suply input
3 VDD_5V 4 VDD_5V
5 VDD_5V 6 VDD_5V
7 GND 8 GND
9 GND 10 VRTC_IN RTC backup battery(3V)input,backup current is 3.5uA
11 VCC_WIFI_IO(3.3V) MMC1 IO reference power,connect to wifi module IO power input 12 VCC_IO(3.3V) 3.3V out for IO reference
13 MMC1_D0 SDIO1/MMC1, connect to wifi module 14 BOOT_CS Pull low this pin to boot from SD CARD on MMC0
15 MMC1_D1 16 PWRKEY Power key
17 MMC1_D2 18 NRESETIN Hard reset input
19 MMC1_D3 20 AliveGPIO3 GPIO, reserved for RecoveryKey
21 MMC1_CMD 22 EXT_PWR_CTRL Used this pin to control power on/off of the carrier
23 GND 24 MMC0_D0 SDIO0/MMC0, for SD Card
25 MMC1_CLK SDIO1 Clock Out 26 MMC0_D1
27 WL_REG_ON(GPIOB24) GPIOB24, Used as wifi power on control signal 28 MMC0_D2
29 WL_HOST_WAKE(GPIOC17) GPIOC17, Used as wifi wake-up signal 30 MMC0_D3
31 UART1_TX UART1, connect to bluetooth module 32 MMC0_CMD
33 UART1_RX 34 MMC0_CD
35 UART1_nCTS 36 MMC0_CLK
37 UART1_nRTS 38 GND
39 BT_RST_N(GPIOB8) GPIOB8, Used as bluetooth reset 40 MIPI_CSI0_CLKN MIPI CSI Clock
41 BT_WAKE bluetooth wake-up signal 42 MIPI_CSI0_CLKP
43 BT_HOST_WAKE(/NC) Reserved for BT_HOST_WAKE 44 GND
45 LPO_32Khz 32.768kHz output for wifi/bt module 46 MIPI_CSI0_D0N MIPI CSI data0
47 GND 48 MIPI_CSI0_D0P
49 MDI0_P GbE MDI signals 50 GND
51 MDI0_N 52 MIPI_CSI0_D1N MIPI CSI data1
53 MDI1_P 54 MIPI_CSI0_D1P
55 MDI1_N 56 GND
57 GND 58 /NC
59 MDI2_P GbE MDI signals 60 /NC
61 MDI2_N 62 GND
63 MDI3_P 64 /NC
65 MDI3_N 66 /NC
67 GND 68 GND
69 SPEED_LED GbE SPEED LED signal output 70 /NC
71 LINK_LED GbE LINK LED signal output 72 /NC
Connector Key
73 GND 74 TP_INT(GPIOC16) I2C signal, connect to touch controller
75 USB_DM4 USB 2.0 host data signal 76 TP_SDA(I2C2_SDA)
77 USB_DP4 78 TP_SCL(I2C2_SCL)
79 GND 80 OneWire(GPIOC15) GPIOC15, used as FriendlyElec LCD OneWire signal
81 USB_DM3 USB 2.0 host data signal 82 GND
83 USB_DP3 84 LCD_CLK RGB LCD Clock signal
85 GND 86 GND
87 USB_DM2 USB 2.0 host data signal 88 LCD_HSYNC RGB LCD horizontal synchronization
89 USB_DP2 90 LCD_VSYNC RGB LCD vertical synchronization
91 GND 92 LCD_DE signal the external LCD that data is valid on the data bus
93 /NC 94 GND
95 /NC 96 LCD_R0 RGB LCD Red data signals
97 GND 98 LCD_R1
99 USB_OTG_D- USB 2.0 OTG data signal 100 LCD_R2
101 USB_OTG_D+ 102 LCD_R3
103 USB_OTG_ID USB 2.0 OTG ID signal 104 LCD_R4
105 VBUS USB 2.0 OTG VBUS 106 LCD_R5
107 VBUS_DRIVE(/NC) Reserved for USB 2.0 OTG VBUS Power Drive Signal 108 LCD_R6
109 HDMI_HPD HDMI Hot plug detect 110 LCD_R7
111 I2C1_SDA I2C1, used as HDMI DDC signal 112 GND
113 I2C1_SCL 114 LCD_G0 RGB LCD Green data signals
115 HDMI_CEC HDMI CEC Signal 116 LCD_G1
117 GND 118 LCD_G2
119 HDMI_TXCN HDMI Clock and data signals 120 LCD_G3
121 HDMI_TXCP 122 LCD_G4
123 GND 124 LCD_G5
125 HDMI_TX0N 126 LCD_G6
127 HDMI_TX0P 128 LCD_G7
129 GND 130 GND
131 HDMI_TX1N 132 LCD_B0 RGB LCD Blue data signals
133 HDMI_TX1P 134 LCD_B1
135 GND 136 LCD_B2
137 HDMI_TX2N 138 LCD_B3
139 HDMI_TX2P 140 LCD_B4
141 GND 142 LCD_B5
143 USB_DM1 USB 2.0 data signal 144 LCD_B6
145 USB_DP1 146 LCD_B7
147 GND 148 GND
149 /NC 150 LVDS_Y3M LVDS signals
151 /NC 152 LVDS_Y3P
153 GND 154 GND
155 /NC 156 LVDS_CLKM
157 /NC 158 LVDS_CLKP
159 GND 160 GND
161 GPIOB31 GPIOs 162 LVDS_Y2M
163 GPIOB30 164 LVDS_Y2P
165 GPIOC7 166 GND
167 GPIOC8 168 LVDS_Y1M
169 GPIOB23 170 LVDS_Y1P
171 GPIOC2 172 GND
173 GPIOC13/PWM1 PWMs 174 LVDS_Y0M
175 GND 176 LVDS_Y0P
177 GPIOC14/PWM2 178 GND
179 GPIOD1/PWM0 180 SPI0_CLK/GPIOC29 SPI
181 I2C2_SDA I2Cs 182 SPI0_MOSI/GPIOC31
183 I2C2_SCL 184 SPI0_MISO/GPIOD0
185 I2C0_SDA 186 SPI0_CS/GPIOC30
187 I2C0_SCL 188 GPIOD8/PPM
189 GPIOB27/HP_DETECT GPIOB27, used as Headphone insert detect 190 UART4_TX/GPIOB29 UARTs
191 AUDIO_GND Headphone output return path 192 UART4_RX/GPIOB28
193 HP_R Headphone output R 194 UART3_RX/GPIOD17
195 HP_L Headphone output L 196 UART3_TX/GPIOD21
197 LINEOUT_R(HP_R) Internal connect to HP_R, reserved for line out R in the future 198 UART2_RX
199 LINEOUT_L(HP_L) Internal connect to HP_L, reserver for line out L in the future 200 UART2_TX
201 MICIN_N Microphone input N 202 UART0_RX Used as Debug console
203 MICIN_P Microphone input L 204 UART0_TX
Note:
  1. For more details refer to the document: []

4.2 Board Dimension

SOM-4418 Dimensions

For more details refer to the document: []

5 Notes in Hardware Design

5.1 EEPROM

  • The board has an EEPROM(model: 24AA025E48T-I/OT) with a unique MAC. This EEPROM is connected to I2C0 and its address is 0x51 therefore some EEPROM chips cannot be connected to I2C0 which will cause conflicts of addresses.
  • In our tests these EEPROM chips cannot be connected to I2C0: 24C04, 24C08 and 24C16. There chips which we tested can be connected to I2C0: 24C01, 24C02 and 24C256
  • For more details about EEPROM address issues refer to http://www.onsemi.com/pub_link/Collateral/CAT24C01-D.PDF

6 Schematics & Mechanical drawing