Matrix - Analog to Digital Converter

查看中文

1 Introduction

Analog to Digital Converter

• The Matrix-Analog_to_Digital_Converter is a single-chip, single-supply low-power 8-bit CMOS data acquisition device.
• It utilizes the PCF8591 chip with four analog inputs, one analog output and a serial I2C-bus interface. Three address pins A0, A1 and A2 are used for programming the hardware address, allowing

the use of up to eight devices connected to the I2C-bus without additional hardware. Address, control and data to and from the device are transferred serially via the two-line bidirectional I2C-bus. The maximum conversion rate is given by the maximum speed of the I2C-bus.

• The I2C hardware address is configured to 1001000x
• The operating supply voltage is from 2.5V to 6.0V，Among the 2.54 mm spacing pin header the 5V pin is the supply voltage. If you need 0 - 3.3V analog signals and keep the acquisition resolution you can connect it to a 3.3V supply voltage.

2 Features

• Wide range supply voltage: 2.5V - 6.0V
• I2C interface: 3.3V/5V
• 8-bit A/D x 4
• 8-bit D/A x 1
• Small and easy to be used in various situations
• 2.54 mm spacing pin
• PCB dimension (mm): 16 x 24

• Pin Description:

Pin	Description
SDA	I2C SDA
SCL	I2C SCL
5V	Supply Voltage 5V
GND	Ground
AOUT	Analog Output
A3	Analog Input3
A2	Analog Input2
A1	Analog Input1
A0	Analog Input0

3 Basic Device Operation

The PCF8591's I2C-bus is for bidirectional, two-line communication between different ICs or modules. The two lines are a Serial DAta line (SDA) and a Serial CLock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor. Data transfer may be initiated only when the bus is not busy. The AINT0 - AINT4 pins are analog inputs which can be configured to single-ended or differential inputs. The supply voltage is 0 - VDD.
1. Each PCF8591 device in an I2C-bus system is activated by sending a valid address to the device. The address consists of a fixed part and a programmable part. The programmable part must be set according to the address pins A0, A1 and A2. The address is always sent as the first byte after the start condition in the I2C-bus protocol. The last bit of the address byte is the read/write-bit which sets the direction of the following data transfer.
2. The second byte sent to a PCF8591 device is stored in its control register and is required to control the device function. The upper nibble of the control register is used for enabling the analog output, and for programming the analog inputs as single-ended or differential inputs. The lower nibble selects one of the analog input channels defined by the upper nibble.
3. The on-chip D/A converter and a high-gain comparator are used temporarily during an A/D conversion cycle. An A/D conversion cycle is always started after sending a valid read mode address to a PCF8591 device. The A/D conversion cycle is triggered at the trailing edge of the acknowledge clock pulse and is executed while transmitting the result of the previous conversion。

4 Download Matrix Source Code

All the matrix modules' code samples are open source. They are maintained on GitHub - git://github.com/friendlyarm/matrix.git
Each branch in this hub contains the matrix modules' code samples for a board that the matrix modules can work with.

• The nanopi branch contains the matrix modules' code samples for the NanoPi
• The tiny4412 branch contains the matrix modules' code samples for the Tiny4412
• The raspberrypi branch contains the matrix modules' code samples for the RaspberryPi

Please follow the steps below to get the source code:
Install the git utility on a PC running Ubuntu14.04

$ sudo apt-get install git

Clone the matrix code from GitHub

$ git clone git://github.com/friendlyarm/matrix.git

If this is successful a "matrix" directory will be generated, which will contain all the matrix modules' code samples.

5 Connect to NanoPi

5.1 Preparations

Please install a Debian on a NanoPi and an appropriate cross compiler on a PC. Please refer to wiki:NanoPi
Compile a NanoPi kernel. Note: please use the kernel's source code from the nanopi-v4.1.y-matrix branch.

$ git clone https://github.com/friendlyarm/linux-4.x.y.git
$ cd linux-4.x.y
$ git checkout nanopi-v4.1.y-matrix
$ make nanopi_defconfig
$ touch .scmversion
$ make

5.2 Hardware Connection

Please refer to the following connection diagram to connect the Matrix-Analog_to_Digital_Converter to the NanoPi

Connection Details:

Matrix-Analog_to_Digital_Converter	NanoPi
SDA	Pin3
SCL	Pin5
5V	Pin4
GND	Pin6

5.3 Compile Test Program

Please login the matrix hub and enter the nanopi branch

$ cd matrix
$ git checkout nanopi

Compile the matrix code

$ make CROSS_COMPILE=arm-linux- clean
$ make CROSS_COMPILE=arm-linux-
$ make CROSS_COMPILE=arm-linux- install

Note: please make sure to install the cross compiler "arm-linux-gcc-4.4.3" on your PC, which is used to compile files for the NanoPi-Debian.
Generated library files are under the "install/lib" directory. Applications are under the "install/usr/bin" directory. The test program for the "Matrix-Ultrasonic_Ranger" module is "matrix-ultrasonic_ranger".

5.4 Run Test Program

Please copy the library files and test program to the NanoPi

$ cp install/usr/bin/* nanopi_rootfs/usr/bin/
$ cp install/lib/* nanopi_rootfs/lib/ -d

Power on the NanoPi and run the following command in Debian's terminal
Note: this module is not plug and play therefore before running the module please make sure it is connected to a NanoPi.

$ matrix-analog_to_digital_converter

5.5 代码展示

int main(int argc, char ** argv)
{
    int devFD;
    int data, channel, mode;
 
    if ((devFD = pcf8591Init()) == -1) {
        printf("Fail to init pcf8591\n");
        return -1;
    }
 
    if (pcf8591SetCtrl(devFD, PCF8591_INIT_AD_CONTROL) == -1) {
        printf("Fail to Set pcf8591 control AD\n");
        pcf8591DeInit(devFD);
        return -1;
    }
 
    mode = 0;
    printf("pcf8591 working as AD in mode%d\n",mode);
    for (channel = PCF8591_AIN_CHANNEL0; channel <= PCF8591_AIN_CHANNEL3; channel++) {
        data = pcf8591Read(devFD, mode, channel);
        printf("Channel%d's value: %d\n",channel,data);
    }
 
    pcf8591DeInit(devFD);
    return 0;
}

6 与Tiny4412连接使用

6.1 准备工作

参考Tiny4412光盘里的《友善之臂Ubuntu使用手册》，在Tiny4412上运行UbuntuCore系统，然后在主机PC上安装并使用相应的编译器。
注意：只能使用Tiny4412SDK-1506的底板。

6.2 硬件连接

参考下图连接模块Matrix-Analog_to_Digital_Converter和Tiny4412

连接说明：

Matrix-Analog_to_Digital_Converter	NanoPi
SDA	CON18 SDA
SCL	CON18 SCL
5V	CON18 5V
GND	CON18 GND

6.3 编译测试程序

进入Matrix代码仓库，切换到tiny4412分支

$ cd matrix
$ git checkout tiny4412

编译Matrix配件代码

$ make CROSS_COMPILE=arm-linux-gnueabihf- clean
$ make CROSS_COMPILE=arm-linux-gnueabihf-
$ make CROSS_COMPILE=arm-linux-gnueabihf- install

注意：请确保你的主机PC当前使用的交叉编译器为Tiny4412-UbuntuCore配套的arm-linux-gnueabihf-gcc-4.7.3。
编译出来的库文件位于install/lib目录下，而测试程序则位于install/usr/bin目录下，模块Matrix-Analog_to_Digital_Converter对应的测试程序为matrix-analog_to_digital_converter。

6.4 运行测试程序

拷贝库文件和测试程序到Tiny4412的UbuntuCore的文件系统上

$ cp install/usr/bin/* tiny4412_rootfs/usr/bin/
$ cp install/lib/* tiny4412_rootfs/lib/ -d

然后启动Tiny4412，在UbuntuCore的shell终端中执行如下命令运行模块Matrix-Analog_to_Digital_Converter的测试程序

$ matrix-analog_to_digital_converter

6.5 代码展示

int main(int argc, char ** argv)
{
    int devFD;
    int data, channel, mode;
 
    if ((devFD = pcf8591Init()) == -1) {
        printf("Fail to init pcf8591\n");
        return -1;
    }
 
    if (pcf8591SetCtrl(devFD, PCF8591_INIT_AD_CONTROL) == -1) {
        printf("Fail to Set pcf8591 control AD\n");
        pcf8591DeInit(devFD);
        return -1;
    }
 
    mode = 0;
    printf("pcf8591 working as AD in mode%d\n",mode);
    for (channel = PCF8591_AIN_CHANNEL0; channel <= PCF8591_AIN_CHANNEL3; channel++) {
        data = pcf8591Read(devFD, mode, channel);
        printf("Channel%d's value: %d\n",channel,data);
    }
 
    pcf8591DeInit(devFD);
    return 0;
}

9 相关资料

PCF8591.pdf