View source for NanoPi M4V2

[[NanoPi M4V2/zh|查看中文]]

==Introduction==
[[File:NanoPi M4V2-01B.jpg|thumb|Overview]]
[[File:NanoPi M4V2-A01.jpg|thumb|Front]]
[[File:NanoPi M4V2-B01.jpg|thumb|Back]]
*The NanoPi M4V2 is a RK3399 SoC based ARM board. It has the same form of factor as the RPi B3+ and has ports and interfaces compatible with RPi B3+ too. On a 85 x 56 mm compact board there are rich hardware resources. These features make it a good platform for rapid product prototyping and various applications.
*The NanoPi M4V2 has an onboard 2.4G & 5G dual-band WiFi + Bluetooth 4.1 combo wireless module, four USB3.0 Type A host ports, one Gbps Ethernet port, one HDMI 2.0 Type A port, one 3.5mm audio jack and one Type-C port. In addition it has a RPi compatible 40-pin connector, dual MIPI-CSI camera interface, PCIe x2, USB2.0 x2, eMMC socket, RTC port and etc.
*The NanoPi M4V2 supports Ubuntu Desktop 18.04(64-bit), Lubuntu 16.04(32-bit), Ubuntu Core 18.04(64-bit), Android 8 and Lubuntu Desktop with GPU and VPU acceleration. With these rich resources and powerful performance it can be widely used in applications of machine learning, AI, deep learning, robots, industrial control, industrial cameras, advertisement machines, game machines, blockchain and etc.

==Hardware Spec==
* SoC: Rockchip RK3399
** CPU: big.LITTLE，Dual-Core Cortex-A72(up to 2.0GHz) + Quad-Core Cortex-A53(up to 1.5GHz)
** GPU: Mali-T864 GPU，supports OpenGL ES1.1/2.0/3.0/3.1, OpenCL, DX11, and AFBC
** VPU: 4K VP9 and 4K 10bits H265/H264 60fps decoding, Dual VOP, etc
* PMU: RK808-D PMIC, cooperated with independent DC/DC, enabling DVFS, software power-down, RTC wake-up, system sleep mode
* RAM: Dual-Channel 4GB LPDDR4
* Flash: no Onboard eMMC, but has a eMMC socket
* Ethernet: Native Gigabit Ethernet
* Wi-Fi/BT: 802.11a/b/g/n/ac, Bluetooth 4.1, Wi-Fi and Bluetooth combo module, 2x2 MIMO, dual antenna interface
* Video Input: one or two 4-Lane MIPI-CSI, dual ISP, up to 13MPix/s，supports simultaneous input of dual camera data
* Video output
** HDMI: HDMI 2.0a, supports 4K@60Hz，HDCP 1.4/2.2
** one 4-Lane MIPI-DSI
* Audio Out: 3.5mm Dual channel headphone jack, or HDMI
* Audio In: one microphone input interface
* USB 3.0: four USB 3.0 Type-A ports
* USB Type-C: Supports USB2.0 OTG and Power input
* microSD Slot x 1
* 40Pin GPIO Extension ports: 
** 3 X 3V/1.8V I2C, up to 1 x 3V UART, 1 X 3V SPI, 1 x SPDIF_TX, up to 8 x 3V GPIOs
** 1 x 1.8V 8 channels I2S 
* 24Pin Extension ports: 
** 2 independent native USB 2.0 Host
** PCIe x2
** PWM x1, PowerKey
* Buttons：one PowerKey, one Recovery Key
* Debug: one Debug UART, 4 Pin 2.54mm header, 3V level, 1500000bps
* LED: 1 x power LED and 1 x GPIO Controlled LED
* RTC Battery: 2 Pin 1.27/1.25mm RTC battery input connector
* Power supply: DC 5V/3A
* PCB: 8 Layer, 85 mm x 56 mm
*Ambient Operating Temperature: -20℃ to 70℃

==Diagram, Layout and Dimension==
===Layout===
[[File:NanoPi_M4V2_Layout.jpg |thumb|600px|NanoPi M4V2 Layout]]
* '''40-Pin GPIO1 Pin Spec'''
::{| class="wikitable"
|-
|'''Pin#''' || '''Assignment'''          ||'''Pin#'''  || '''Assignment'''     
|-
|1    || VCC3V3_SYS  ||2     || VDD_5V
|-
|3    || I2C2_SDA(3V)      ||4     || VDD_5V
|- 
|5    || I2C2_SCL(3V)      ||6     || GND
|-
|7    || GPIO1_A0(3V)      ||8     || GPIO4_C1/I2C3_SCL(3V)
|-
|9    || GND          ||10    || GPIO4_C0/I2C3_SDA(3V) 
|-
|11   || GPIO1_A1(3V)       ||12    || GPIO1_C2(3V)
|-
|13   || GPIO1_A3(3V)      ||14    || GND
|-
|15   || GPIO1_A4(3V)      ||16    || GPIO1_C6(3V)
|-
|17   || VCC3V3_SYS ||18    || GPIO1_C7(3V)
|-
|19   || SPI1_TXD/UART4_TX(3V)     ||20    || GND
|-
|21   || SPI1_RXD/UART4_RX(3V)     ||22    || GPIO1_D0(3V)
|-
|23   || SPI1_CLK(3V)     ||24    || SPI1_CSn0(3V)
|-
|25   || GND          ||26     || GPIO4_C5/SPDIF_TX(3V)
|-
|27   || I2C2_SDA(1.8V)      ||28     || I2C2_SCL(1.8V)
|-
|29   || I2S0_LRCK_RX(1.8V)       ||30     || GND
|-
|31   ||I2S0_LRCK_TX(1.8V)     ||32     || I2S_CLK(1.8V)
|-
|33   || I2S0_SCLK(1.8V)      ||34     || GND
|-
|35   || I2S0_SDI0(1.8V)    ||36     || I2S0_SDO0(1.8V)
|-
|37   || I2S0_SDI1SDO3(1.8V)     ||38     || I2S0_SDI2SDO2(1.8V)
|-
|39   || GND          ||40     || I2S0_SDI3SDO1(1.8V)
|}

* '''24-Pin GPIO2 Pin Spec'''
::{| class="wikitable"
|-
|'''Pin#''' || '''Assignment'''          ||'''Pin#'''  || '''Assignment'''     
|-
|1    || VCC5V0_SYS  ||2     || VCC5V0_SYS
|-
|3    || PCIE_RX1_P      ||4     || PCIE_TX1P
|- 
|5    || PCIE_RX1_N      ||6     || PCIE_TX1N
|-
|7    || GND      ||8     || GND
|-
|9    || PCIE_RX0_P          ||10    || PCIE_TX0P
|-
|11   || PCIE_RX0_N       ||12    || PCIE_TX0N
|-
|13   || GND      ||14    || GND
|-
|15   || PCIE_REF_CLKP      ||16    || HOST0_DM
|-
|17   || PCIE_REF_CLKN ||18    || HOST0_DP
|-
|19   || GND     ||20    || GND
|-
|21   || PWR_KEY     ||22    || HOST1_DM
|-
|23   || GPIO4_C6/PWM1(3V)     ||24    || HOST1_DP
|}

* '''MIPI-CSI Interface Pin Spec'''
:: 0.5mm FPC Connector
:: MIPI-CSI2 can be configured to MIPI-DSI
::{| class="wikitable"
|-
|'''Pin#''' ||   '''MIPI-CSI1'''  ||  '''MIPI-CSI2'''   ||   '''Description '''   
|-
|1    ||  VCC5V0_SYS  || VCC5V0_SYS   ||   5V Power ouput
|-
|2    ||  VCC5V0_SYS || VCC5V0_SYS    ||  5V Power ouput
|- 
|3    ||     GND     ||  GND          ||   Return current path
|-
|4    || VCC_CSI_AF2.8V || VCC_CSI_AF2.8V || 2.8V Power for VCM 
|-
|5    || VCC_CSI_1.2V  || VCC_CSI_1.2V  || 1.2V Power for image sensor core circuit
|- 
|6    ||  VCC1V8_CAM  ||   VCC1V8_CAM   || 1.8V power for I/O circuit
|-
|7    ||  VCC_CSI_2.8V || VCC_CSI_2.8V || 2.8V power for image sensor analog circuit
|-
|8    ||  VCC_CSI_1.0V || VCC_CSI_1.0V || 1.0V Power for image sensor core circuit
|- 
|9    || I2C1_SCL ||   I2C2_SCL        || 1.8V I2C clock signal
|-
|10    || I2C1_SDA || I2C2_SDA         ||  1.8V I2C data signal
|-
|11    || MIPI_CSI0_RST || MIPI_CSI1_RST || reset  camera module 
|- 
|12    || MIPI_CSI0_PWN || MIPI_CSI1_PWN  || Power down camera module 
|-
|13     ||  GND          ||      GND          || Return current path
|-
|14    || GPIO2_B3_CIF_CLKOUTA || GPIO2_B3_CIF_CLKOUTA || MCLK to camera module
|-
|15      || GND           ||     GND            || Return current path
|-
|16    ||  MIPI_RX0_D3P  || MIPI_TX1/RX1_D3P   || MIPI CSI positive differential data line transceiver output 
|- 
|17    ||  MIPI_RX0_D3N || MIPI_TX1/RX1_D3N    || MIPI CSI negative differential data line transceiver output 
|-
|18    ||   GND    || GND                      || Return current path
|- 
|19    || MIPI_RX0_D2P || MIPI_TX1/RX1_D2P   || MIPI CSI positive differential data line transceiver output 
|-
|20    || MIPI_RX0_D2N || MIPI_TX1/RX1_D2N    || MIPI CSI negative differential data line transceiver output 
|-
|21    || GND || GND     || Return current path
|- 
|22    ||  MIPI_RX0_D1P  || MIPI_TX1/RX1_D1P   || MIPI CSI positive differential data line transceiver output 
|-
|23    || MIPI_RX0_D1N || MIPI_TX1/RX1_D1N    || MIPI CSI negative differential data line transceiver output 
|-
|24    || GND || GND    || Return current path
|- 
|25    || MIPI_RX0_CLKP || MIPI_TX1/RX1_CLKP   || MIPI CSI positive differential clock line transceiver output
|-
|26    || MIPI_RX0_CLKN || MIPI_TX1/RX1_CLKN    || MIPI CSI negative differential clock line transceiver output
|- 
|27    || GND ||  GND   || Return current path
|-
|28    || MIPI_RX0_D0P || MIPI_TX1/RX1_D0P || MIPI CSI positive differential data line transceiver output 
|-
|29    || MIPI_RX0_D0N || MIPI_TX1/RX1_D0N  || MIPI CSI negative differential data line transceiver output 
|- 
|30    || GND      ||  GND     || Return current path
|}
* '''eMMC Socket Pin Spec'''
::{| class="wikitable"
|-
|'''Pin#''' || '''Assignment'''          ||'''Pin#'''  || '''Assignment'''     
|-
|1    || EMMC_D0  ||2     || EMMC_D1
|-
|3    || EMMC_D2     ||4     || EMMC_D3
|- 
|5    || EMMC_D4      ||6     || EMMC_D5
|-
|7    || EMMC_D6     ||8     || EMMC_D7
|-
|9    || EMMC_STRB          ||10    || GND 
|-
|11   || EMMC_CMD      ||12    || EMMC_CLKO
|-
|13   || N/C     ||14    || GND
|-
|15   || N/C     ||16    || VCC1V8_S3
|-
|17   || eMMC_RST  ||18    || VCC3V3_S3
|-
|19   || GND     ||20    || GND
|}
* '''Debug UART Pin Spec'''
:: 3V level signals, 1500000bps
::{| class="wikitable"
|-
|'''Pin#''' ||'''Assignment''' ||   '''Description '''   
|-
|1    || GND                 || 0V
|-
|2    || VCC5V0_SYS          || 5V power output
|- 
|3    || UART2DBG_TX         || output
|-
|4    || UART2DBG_RX         || intput
|}

*'''USB Port'''
::USB 3.0 port has 2A overcurrent protection.

*'''RTC'''
::RTC backup current is 27uA.
::Connector P/N: Molex 53398-0271
:'''Notes'''
::#Power Input : 5V/3A, via USB Type-C(USB PD Specification is not supported) or Pin2&Pin4 of the 40-pin GPIO1 header
::#For more details refer to the Schematic: [http://wiki.friendlyelec.com/wiki/images/c/cc/NanoPi-M4V2_1908_Schematic.pdf NanoPi-M4V2_1908_Schematic.pdf]

===Board Dimension===
::For more details refer to the CAD document: [http://wiki.friendlyelec.com/wiki/images/2/21/NanoPi_M4V2_1908%28DXF%29.zip NanoPi_M4V2_1908(DXF).zip]

==Get Started==
===Essentials You Need===
Before starting to use your NanoPi-M4V2 get the following items ready
* NanoPi-M4V2
* Type-C cable
* TF Card: Class 10 or Above, minimum 8GB SDHC
* USB to serial adapter(optinal, for debugging or access from PC host)
* 5V/3A Power adapter
* HDMI monitor or LCD
* USB keyboard, mouse and possible a USB hub(or a TTL to serial board)
* A host computer running <b>Ubuntu 18.04 64-bit system</b>
===Install OS===
{{Downloads-RK3399|NanoPi-M4V2}}
{{BurnLinuxToSD-Rockchip|NanoPi-M4V2}}
{{RK3399-DebugPort|NanoPi-M4V2}}
==Work with Debian11 Desktop==
===Introduction to Debian11 Desktop===
{{DebianBullseyeDesktop-Intro|NanoPi-M4V2}}
{{DebianBullseyeDesktop-Common|NanoPi-M4V2}}
{{DebianBullseyeDesktop-WithHDMI|NanoPi-M4V2}}
==Work with Debian10 Desktop==
* Refer to：
** [[Debian Buster Desktop|Debian Buster]]
==Work with FriendlyDesktop==
{{FriendlyDesktop-Intro|NanoPi-M4V2}}
{{FriendlyDesktop-Contents|NanoPi-M4V2}}
===Using NVME SSD on FriendlyDesktop===
Please see this article: [[Template:How to Initialize and Format New SSD And HDD|How to Initialize and Format New SSD And HDD]]<br />
{{FriendlyCoreGeneral|NanoPi-M4V2}}
{{FriendlyCoreRunX11Application|NanoPi-M4V2}}
{{RK3399 Linux mpv|NanoPi-M4V2}}
==Features applicable to FriendlyDesktop and FriendlyCore==
{{Linux-RK3399MIPICamera|NanoPi-M4V2}}
{{RK3399-Linux-Install-Docker|NanoPi-M4V2}}
{{RK3399 Linux FFmpeg|NanoPi-M4V2}}
{{How to Initialize and Format New SSD And HDD|NanoPi-M4V2}}
===Using 4G Module EC20 on Linux===
Please see this article: [[How to use 4G Module on NanoPC-T4]]<br />
==Buildroot Linux==
{{RK3399 Buildroot Intro|NanoPi-M4V2}}
<br />
For a more detailed description of the Buildroot system, please refer to: [[Buildroot|Buildroot]]<br />
==Work with Lubuntu==
See here: [[Lubuntu desktop 16.04 for RK3399]]<br />
Using NVME SSD on Lubuntu: [[Template:How to Initialize and Format New SSD And HDD|How to Initialize and Format New SSD And HDD]]<br />
{{RK3399-Android8|NanoPi-M4V2}}
{{RK3399-Android-USBCamera|NanoPi-M4V2}}
{{RK3399-Android-4G-EC20|NanoPi-M4V2}}
{{RK3399-Android-SSD|NanoPi-M4V2}}
==Work with Android7.1==
See here: [[RK3399-Android7|Android7]]
==How to Compile==
{{Rockchip-DevEnv|NanoPi-M4V2}}
{{RK3399-BuildFromSource|NanoPi-M4V2}}
{{RK3399-HWAccess|NanoPi-M4V2}}
{{RockchipMiscCustome|RK3399}}

==The usage of eMMC module==
[[File:NanoPi_M4V2-eMMC.jpg|frameless|500px]]
{{BurnLinuxToEMMC-Rockchip/zh|NanoPi-M4V2}}

{{MoreOS}}
==Link to Rockchip Resources==
*[http://opensource.rock-chips.com/images/d/d7/Rockchip_RK3399_Datasheet_V2.1-20200323.pdf RK3399 datasheet V2.1]
*[http://opensource.rock-chips.com/images/e/ee/Rockchip_RK3399TRM_V1.4_Part1-20170408.pdf RK3399TRM V1.4]

==Schematic, PCB CAD File==
*Schematic:  [http://wiki.friendlyelec.com/wiki/images/c/cc/NanoPi-M4V2_1908_Schematic.pdf NanoPi-M4V2_1908_Schematic.pdf]
*PCB CAD File：[http://wiki.friendlyelec.com/wiki/images/2/21/NanoPi_M4V2_1908%28DXF%29.zip NanoPi_M4V2_1908(DXF).zip]

==Update Log==
{{RK3399-UpdateLog|NanoPi-M4V2}}