View source for NanoHat OLED

[[NanoHat OLED/zh|查看中文]]

==Introduction==
[[File:NanoHat Oled.png|thumb|0.96inch 128x64 OLED]]
*NanoHat OLED is a small and cute monochrome OLED module with low power consumption. It is 0.96". Its resolution is 128 x 64. It communicates with a master device with I2C.
*The NanoHat OLED module has the same form factor as FriendlyElec's NanoPi NEO. It can be stacked on a NanoPi NEO.
*It has three onboard programmable user buttons, a 2.0mm pitch 4-Pin I2C connector.

==Hardware Spec==
* Display Area:0.96"
* Resolution: 128 x 64
* High Contrast, Low Power Consumption
* 3 x Onboard Button
* PCB Dimension(mm): 40 x 40
[[File:NanoHat OLED.png|frameless|400px|NanoHat OLEDPCB]]

* '''GPIO Pin Description'''
::{| class="wikitable"
|-
|Pin# || Name || Linux gpio ||Pin#  || Name || Linux gpio       
|-
|1    || SYS_3.3V   ||     ||2     || VDD_5V ||
|-
|3    || I2C0_SDA   ||     ||4     || VDD_5V ||
|- 
|5    || I2C0_SCL   ||     ||6     || GND    ||
|-
|7    || NC    ||  ||8     || NC || 
|-
|9    || GND        ||     ||10    || NC || 
|-
|11   || K1  || 0      ||12    || NC || 
|-
|13   || K2 || 2      ||14    || GND || 
|-
|15   || K3 || 3      ||16    || NC || 
|-
|17   || SYS_3.3V     ||        ||18    || NC || 
|-
|19   || NC ||      ||20    || GND              ||
|-
|21   || NC ||      ||22    || NC || 
|-
|23   || NC ||      ||24    || NC || 
|}
Only GND and 5V on the 12-Pin land are connected and the rest pins are open. For more details on the 12-Pin connector refer to NanoPi NEO/Air/NEO2's wiki site.

==Hardware Setup==
Currently only the NanoPi NEO, NEO2 and NanoPi NEO Air work with this module.
The NanoHat OLED module has the same form factor as FriendlyElec's NanoPi NEO. It can be stacked on a NanoPi NEO/NEO2/Air.
Here is a hardware setup:<br>
[[File:NanoHat OLED_nanopi_NEO.jpg|frameless|600px|NanoHat OLED_nanopi_NEO]]<br>
Applicable Boards:<br />
NanoPi NEO<br />
NanoPi NEO Air<br />
NanoPi NEO2<br />
NanoPi NEO Plus2<br />

==Install Software==
There are some code samples for NanoHat OLED. You can get these samples by running the following commands under Ubuntu core:<br />
<syntaxhighlight lang="bash">
git clone https://github.com/friendlyarm/NanoHatOLED.git
cd NanoHatOLED
sudo -H ./install.sh
</syntaxhighlight>
<br />
<!---
The script downloads and installs the samples and some utilities. Mainland Chinese users can download them faster by changing the source:<br />
Open the "/etc/apt/sources.list" file, copy the following lines to replace the existing contents:<br />
<syntaxhighlight lang="bash">
deb http://mirrors.ustc.edu.cn/ubuntu-ports/ xenial main multiverse restricted universe
deb http://mirrors.ustc.edu.cn/ubuntu-ports/ xenial-backports main multiverse restricted universe
deb http://mirrors.ustc.edu.cn/ubuntu-ports/ xenial-proposed main multiverse restricted universe
deb http://mirrors.ustc.edu.cn/ubuntu-ports/ xenial-security main multiverse restricted universe
deb http://mirrors.ustc.edu.cn/ubuntu-ports/ xenial-updates main multiverse restricted universe
deb-src http://mirrors.ustc.edu.cn/ubuntu-ports/ xenial main multiverse restricted universe
deb-src http://mirrors.ustc.edu.cn/ubuntu-ports/ xenial-backports main multiverse restricted universe
deb-src http://mirrors.ustc.edu.cn/ubuntu-ports/ xenial-proposed main multiverse restricted universe
deb-src http://mirrors.ustc.edu.cn/ubuntu-ports/ xenial-security main multiverse restricted universe
deb-src http://mirrors.ustc.edu.cn/ubuntu-ports/ xenial-updates main multiverse restricted universe
</syntaxhighlight>
Or edit(or create) the "$HOME/.pip/pip.conf" file and set Python's pip to a mainland Chinese source. Here is what pip.conf looks like:
<syntaxhighlight lang="bash">
[global]
trusted-host =  mirrors.aliyun.com
index-url = http://mirrors.aliyun.com/pypi/simple
</syntaxhighlight>
After these commands are executed run "sudo apt-get update" to update software packages and then run "./install.sh" to begin installation.
<br />
--->

==Run Code Samples==

After the code samples are installed they will automatically run on system reboot and display date and time<br />
Here are the definitions of the NanoHat OLED's three user buttons:<br />
K1 -> Show date & time; <br />
K2 -> Show master device's system status: IP address, CPU usage, RAM, CPU temperature and etc; <br />
K3 -> Shutdown. After this button is pressed system will not be shut down immediately but will pop up a Yes/No dialog. Pressing K1 switches between Yes and No, and pressing K2 is to confirm the selection.<br />
<br />

==Resources==

==Update Log==
===April-27-2017===
* Released English Version