Matrix - 3-Axis Digital Accelerometer

From FriendlyELEC WiKi
Jump to: navigation, search

查看中文

1 Introduction

3-Axis Digital Accelerometer
  • This module measures the static acceleration of gravity in three axis x, y and z resulting from motion or shock.
  • Its digital interface is IIC or SPI.
  • It is integrated with an ADXL345 chip with high resolution (13-bit) measurement at ±2g, ±4g, ±8g and ±16g.
  • The module is powered by 5V and converts 5V to 3.3V to ADXL345.

2 Features

  • I2C, 3.3V
  • 13-bit, up to +-16g
  • 2.54mm spacing pin interface
  • PCB dimension(mm): 16 x 32

重力加速度PCB

  • Pin Description:
Pin Description
INT2 Interrupt
INT1 Interrupt
CS Enable
SCL I2C SCL
SDA I2C SDA
SDO Set Slave Address
5V Supply Voltage 5V
GND Ground

3 Basic Device Operation

  • The ADXL345 is a small, thin, ultralow power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos complement and is acces-sible through either a SPI (3- or 4-wire) or I2C digital interface.
  • The ADXL345 is well suited for mobile device applications. It measures the static acceleration of gravity in tilt-sensing appli-cations, as well as dynamic acceleration resulting from motion or shock. Its high resolution (3.9 mg/LSB) enables measurement of inclination changes less than 1.0°.
  • The ADXL345 conforms to the UM1024 I2C Specification. It supports standard (100 kHz) and fast (400 kHz) data transfer modes. If the CS is tied high it will be in the I2C mode. If the CS or ALT ADDRESS pin is floating or unconnected the state will be unknown.
  • The module's I2C connection diagram is as follows:

三轴重力加速度


4 Applications

4.1 Connect to NanoPi M1

Refer to the following connection diagram to connect the module to the NanoPi M1:
Matrix-3_Axis_Digital_Accelerometer_nanopi_m1

Connection Details:

Matrix-3_Axis_Digital_Accelerometer NanoPi M1
INT2 NC
INT1 NC
CS Pin2
SCL Pin5
SDA Pin3
SDO High, it is connected to the GPIO pin-header's 3.3V
5V Pin4
GND Pin6

4.2 Connect to NanoPi 2

Refer to the following connection diagram to connect the module to the NanoPi 2:
Matrix-3_Axis_Digital_Accelerometer_nanopi_2

Connection Details:

Matrix-3_Axis_Digital_Accelerometer NanoPi 2
INT2 NC
INT1 NC
CS Pin2
SCL Pin5
SDA Pin3
SDO High, it is connected to the GPIO pin-header's 3.3V
5V Pin4
GND Pin6

4.3 Connect to NanoPi M2 / NanoPi 2 Fire

Refer to the following connection diagram to connect the module to the NanoPi M2/ NanoPi 2 Fire:
Matrix-3_Axis_Digital_Accelerometer_nanopi_M2

Connection Details:

Matrix-3_Axis_Digital_Accelerometer NanoPi M2
INT2 NC
INT1 NC
CS Pin2
SCL Pin5
SDA Pin3
SDO High, it is connected to the GPIO pin-header's 3.3V
5V Pin4
GND Pin6

4.4 Connect to NanoPC-T2

Refer to the following connection diagram to connect the module to the NanoPC-T2:
Matrix-3_Axis_Digital_Accelerometer_NanoPC-T2

Connection Details:

Matrix-3_Axis_Digital_Accelerometer NanoPC-T2
INT2 NC
INT1 NC
CS USB Host 5V
SCL Pin5
SDA Pin6
SDO USB Host 5V
5V Pin29
GND Pin30



5 Compile & Run Test Program

Boot your ARM board with Debian and copy the matrix code:

$ apt-get update && apt-get install git
$ git clone https://github.com/friendlyarm/matrix.git

If your cloning is done successfully a "matrix" directory will be generated.

Compile and install Matrix:

$ cd matrix
$ make && make install

Run test program:

$ matrix-accelerometer

Note: this module is not plug and play therefore before running the module please make sure it is connected to an ARM board.
Here is what you should observe:

The position is (-6, 3, 236)


6 Code Sample

This Matrix code sample can work with all the ARM boards mentioned in this module's wiki. The name of this code sample is "matrix-3_axis_digital_accelerometer". Here is its source code:

int main(int argc, char ** argv) 
{
    char position[BUF_SIZE];
    int board;
 
    if ((board = boardInit()) < 0) {
        printf("Fail to init board\n");
        return -1;
    }
 
    system("modprobe adxl34x");
    system("modprobe adxl34x-i2c");
    memset(position, 0, BUF_SIZE);
    if (adxl34xRead(position) > 0) {
        printf("The position is %s", position);
    } else {
        printf("Fail to get position\n");        
    }
    system("rmmod adxl34x-i2c");
    system("rmmod adxl34x");
 
    return 0;
}

For more details about this APIs called in this code sample refer to Matrix API reference manual


7 Resources

ADXL345.pdf


8 Update Log

8.1 Feb-23-2016

  • Changed CS pin spec in Section 5.1
  • Added driver's source code location in Section 5.2

8.2 June-17-2016

  • Re-organized and simplified wiki