Difference between revisions of "Template:S5P4418BuildFromSource"

From FriendlyELEC WiKi
Jump to: navigation, search
(Compile Android)
(Compile Linux kernel 3.4.y)
Line 118: Line 118:
 
make uImage
 
make uImage
 
</syntaxhighlight>
 
</syntaxhighlight>
 
 
* Compile Debian Kernel
 
* Compile Debian Kernel
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
Line 132: Line 131:
 
make uImage
 
make uImage
 
</syntaxhighlight>
 
</syntaxhighlight>
After your compilation succeeds a uImage will be generated for HDMI 720P. If you want a uImage for 1080P you can do it this way:
+
After your compilation succeeds a uImage.hdmi will be generated for HDMI 720P. If you want a uImage.hdmi for 1080P you can do it this way:
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
touch .scmversion
 
touch .scmversion
Line 146: Line 145:
 
make uImage
 
make uImage
 
</syntaxhighlight>
 
</syntaxhighlight>
After your compilation succeeds a uImage will be generated for HDMI 1080P. You can use it to replace the existing uImage.hdmi.
+
After your compilation succeeds a uImage.hdmi will be generated for HDMI 1080P. You can use it to replace the existing uImage.hdmi.
  
 
====Use Your Generated Kernel====
 
====Use Your Generated Kernel====

Revision as of 13:58, 26 December 2017

查看中文

1 Make Your Own OS Image

1.1 Install Cross Compiler

Download the compiler package:

git clone https://github.com/friendlyarm/prebuilts.git
sudo mkdir -p /opt/FriendlyARM/toolchain
sudo tar xf prebuilts/gcc-x64/arm-cortexa9-linux-gnueabihf-4.9.3.tar.xz -C /opt/FriendlyARM/toolchain/

Then add the compiler's directory to "PATH" by appending the following lines in "~/.bashrc":

export PATH=/opt/FriendlyARM/toolchain/4.9.3/bin:$PATH
export GCC_COLORS=auto

Execute "~/.bashrc" to make the changes take effect. Note that there is a space after the first ".":

. ~/.bashrc

This compiler is a 64-bit one therefore it cannot be run on a 32-bit Linux machine. After the compiler is installed you can verify it by running the following commands:

arm-linux-gcc -v
Using built-in specs.
COLLECT_GCC=arm-linux-gcc
COLLECT_LTO_WRAPPER=/opt/FriendlyARM/toolchain/4.9.3/libexec/gcc/arm-cortexa9-linux-gnueabihf/4.9.3/lto-wrapper
Target: arm-cortexa9-linux-gnueabihf
Configured with: /work/toolchain/build/src/gcc-4.9.3/configure --build=x86_64-build_pc-linux-gnu
--host=x86_64-build_pc-linux-gnu --target=arm-cortexa9-linux-gnueabihf --prefix=/opt/FriendlyARM/toolchain/4.9.3
--with-sysroot=/opt/FriendlyARM/toolchain/4.9.3/arm-cortexa9-linux-gnueabihf/sys-root --enable-languages=c,c++
--with-arch=armv7-a --with-tune=cortex-a9 --with-fpu=vfpv3 --with-float=hard
...
Thread model: posix
gcc version 4.9.3 (ctng-1.21.0-229g-FA)

1.2 Compile Linux kernel 4.4.y

1.2.1 Compile Kernel

  • Download Kernel Source Code
git clone https://github.com/friendlyarm/linux.git
cd linux
git checkout nanopi2-v4.4.y

The NanoPC-T2's kernel source code is in the "nanopi2-v4.4.y" branch.You need to switch to this branch.

  • Compile Ubuntu Kernel
touch .scmversion
make ARCH=arm nanopi2_linux_defconfig
make ARCH=arm

After your compilation succeeds an "arch/arm/boot/zImage" will be generated and a DTB file(s5p4418-nanopi2-rev*.dtb) will be generated in the "arch/arm/boot/dts/" directory. You can use them to replace the existing zImage and DTB files in the boot section of your bootable SD card.

1.2.2 Use Your Generated Kernel

  • Update kernel in SD card

If you use an SD card to boot Ubuntu you can copy your generated zImage and DTB files to your SD card's boot section(e.g. section 1 /dev/sdX1).

  • Update kernel in eMMC

If you boot your board from eMMC you can update your kernel file by following the steps below:
1) Usually after OS is loaded eMMC's boot section (in our example eMMC's device name was /dev/mmcblk0p1) will be automatically mounted and you can verify that by running "mount"
2) Connect your board to a host PC running Ubuntu and copy the zImage and DTB files to eMMC's boot section
3) Or you can copy your generated kernel file to an external storage card(e.g. an SD card or a USB drive), connect the storage card to your board the move the file from the card to eMMC's boot section
4) After update is done type "reboot" to reboot your board. Note: don't just directly disconnect your board from its power source or press the reset button to reboot the board. These actions will damage your kernel file

  • Generate Your boot.img

If you want to generate an image file that can be flashed to eMMC you need to generate a boot.img file and then copy it to your installation SD card
For Ubuntu follow the steps below to generate a boot.img file:
1) Download debian_nanopi2

git clone https://github.com/friendlyarm/debian_nanopi2.git

2) Copy the zImage and DTB files to replace the corresponding files under the "debian_nanopi2/boot/" directory
3) Generate boot.img

cd debian_nanopi2
mkdir rootfs
./build.sh

A newly generated boot.img will be under the "debian_nanopi2/sd-fuse_nanopi2/debian" directory.
The "mkdir rootfs" command creates a working directory for the build.sh script to run. It also creates some files such as "rootfs.img" but these files are useless.

1.2.3 Compile U-Boot

Download the U-Boot source code and compile it. Note that the github's branch is nanopi2-v2016.01:

git clone https://github.com/friendlyarm/u-boot.git 
cd u-boot
git checkout nanopi2-v2016.01
make s5p4418_nanopi2_defconfig
make CROSS_COMPILE=arm-linux-

After your compilation succeeds a bootloader.img will be generated. If you want to test it flash it to your installation SD card to replace an existing U-Boot v2014.07 file via fastboot, sd-fuse_nanopi2 or eflasher ROM.
Note: you cannot use mixed U-Boot files. For example you cannot use fastboot to update an existing U-Boot V2014.07 and you cannot use bootloader.img to replace an existing u-boot.bin

1.3 Compile Linux kernel 3.4.y

1.3.1 Prepare mkimage

You need the mkimage utility to compile a U-Boot source code package. Make sure this utility works well on your host before you start compiling a uImage.
You can install this utility by either commanding "sudo apt-get install u-boot-tools" or following the commands below:

cd uboot_nanopi2
make CROSS_COMPILE=arm-linux- tools
sudo mkdir -p /usr/local/sbin && sudo cp -v tools/mkimage /usr/local/sbin

1.3.2 Compile Linux Kernel

  • Download Kernel Source Code
git clone https://github.com/friendlyarm/linux-3.4.y.git
cd linux-3.4.y
git checkout nanopi2-lollipop-mr1

The NanoPC-T2's kernel source code lies in the "nanopi2-lollipop-mr1" branch.

  • Compile Android Kernel
make nanopi2_android_defconfig
touch .scmversion
make uImage
  • Compile Debian Kernel
make nanopi2_linux_defconfig
touch .scmversion
make uImage

After your compilation succeeds a uImage will be generated in the "arch/arm/boot/" directory. This kernel is for LCD output. You can use it to replace the existing uImage.
If you want to generate a kernel for HDMI output you need to run nanopi2_linux_hdmi_defconfig and do it this way:

make nanopi2_linux_hdmi_defconfig
touch .scmversion
make uImage

After your compilation succeeds a uImage.hdmi will be generated for HDMI 720P. If you want a uImage.hdmi for 1080P you can do it this way:

touch .scmversion
make nanopi2_linux_hdmi_defconfig
make menuconfig
  Device Drivers -->
    Graphics support -->
      Nexell Graphics -->
        [ ] LCD
        [*] HDMI
        (0)   Display In  [0=Display 0, 1=Display 1]
              Resolution (1920 * 1080p)  --->
make uImage

After your compilation succeeds a uImage.hdmi will be generated for HDMI 1080P. You can use it to replace the existing uImage.hdmi.

1.3.3 Use Your Generated Kernel

  • Update the kernel file in SD card

If you use an SD card to boot Android you can copy your generated uImage file to your SD card's boot section(e.g. section 1 /dev/sdX1).
If you use an SD card to Debian and you generated a uImage for an HDMI monitor you can use that uImage to replace the uImage.hdmi file in the SD card's boot section. If you use an SD card to Debian and you generated a uImage for an LCD you can use that uImage to replace the uImage file in the SD card's boot section.

  • Update Android kernel file in eMMC

If you want to update the kernel file in eMMC you need firstly boot your board, then mount eMMC's boot section, replace the boot section's kernel file with your generated one and reboot your board.
If you boot your board from eMMC you can update your kernel file by following the steps below:
1) After Android is loaded mount eMMC's boot section (in our example eMMC's device name was /dev/mmcblk0p1) by using the following commands:

su
mount -t ext4 /dev/block/mmcblk0p1 /mnt/media_rw/sdcard1/

2) Connect your board to a host PC running Ubuntu and copy the uImage file to eMMC's boot section by running the following commands

adb push uImage /mnt/media_rw/sdcard1/

3) Or you can copy your generated kernel file to an external storage card(e.g. an SD card or a USB drive), connect the storage card to your board the move the file from the card to eMMC's boot section
4) After update is done type "reboot" and enter to reboot your board. Note: don't just directly disconnect your board from its power source or press the reset button to reboot the board. These actions will damage your kernel file

  • Update Debian kernel file in eMMC

If you boot your board from eMMC you can update your kernel file by following the steps below:
1) When Debian is being loaded eMMC's boot section will be automatically mounted(in our example eMMC's device name was /dev/mmcblk0p1). You can use "mount" to verify that
2) Connect your board to a host PC via Ethernet and copy your generated uImage file via scp/ftp to eMMC's boot section and replace the existing file. If your file is for LCD output use your uImage file to replace the existing uImage. If your file is for HDMI output use your uImage.hdmi file to replace the existing uImage.hdmi file
3) Or you can copy your generated kernel file to an external storage card(e.g. an SD card or a USB drive), connect the storage card to your board the move the file from the card to eMMC's boot section
4) After update is done type in "reboot" to reboot your board. Note: don't just directly disconnect your board from its power source or press the reset button to reboot the board. These actions will damage your kernel file

  • Generate Your boot.img

If you want to generate an image file that can be flashed to eMMC you need to generate a boot.img file and copy it to your installation SD card
For Android copy the uImage file to Android source code's "device/friendly-arm/nanopi2/boot/" directory and compile this whole Android source code. After your compilation is successful you will get a boot.img file.
For Debian follow the steps below to generate a boot.img file
1) Download debian_nanopi2

git clone https://github.com/friendlyarm/debian_nanopi2.git

2) Copy the image file for an HDMI monitor and use it to replace the "debian_nanopi2/boot/uImage.hdmi" file and copy the image file for an LCD and use it to replace the "debian_nanopi2/boot/uImage" file
3) Generate Debian's boot.img

cd debian_nanopi2
mkdir rootfs
./build.sh

A newly generated boot.img will be under the "debian_nanopi2/sd-fuse_nanopi2/debian" directory.
The "mkdir rootfs" command creates a working directory for the build.sh script to run. It also creates some files such as "rootfs.img" but these files are useless.

1.3.4 Compile Kernel Modules

Android contains kernel modules which are in the "/lib/modules" directory in the system section. If you want to add your own modules to the kernel or you changed your kernel configurations you need to recompile these new modules.
Compile Original Kernel Modules:

cd linux-3.4.y
make CROSS_COMPILE=arm-linux- modules

Here we have two new modules and we can compile them by running the commands below:

cd /opt/FriendlyARM/s5p4418/android
./vendor/friendly-arm/build/common/build-modules.sh

The "/opt/FriendlyARM/s5p4418/android" directory points to the top directory of Android source code. You can get more details by specifying option "-h".
After your compilation succeeds new modules will be generated

1.3.5 Compile U-Boot

Download the U-Boot v2014.07 source code and compile it. Note that the github's branch is nanopi2-lollipop-mr1: After compilation is done a u-boot.bin will be generated and you can update your NanoPC-T2's u-boot with fastboot by running the following commands:
1) On your host PC run "sudo apt-get install android-tools-fastboot" to installl the fastboot utility;
2) Connect your NanoPC-T2 to your host PC, boot your NanoPC-T2 and press "Enter" within two seconds right after your board is powered on and you will enter the u-boot commandline:
3) In the commandline window type "fastboot" and then press "Enter" to enter the fastboot mode:
4) Connect your NanoPC-T2 to a host PC with a MicroUSB cable and run the following commands in the commandline window to flash u-boot.bin to your NanoPC-T2:

fastboot flash bootloader u-boot.bin


Note:you cannot use "dd" to update your SD card in this situation.

1.4 Compile Android

We provide two Android versions: Android 4.4 and Android 5.1. Both of them are compiled the same way.

  • Install Cross Compiler

Install 64 bit Ubuntu 16.04 on your host PC.

sudo apt-get install bison g++-multilib git gperf libxml2-utils make python-networkx zip
sudo apt-get install flex libncurses5-dev zlib1g-dev gawk minicom

For more details refer to https://source.android.com/source/initializing.html

  • Download Android 5.1's Source Code

You need to use repo to get the Android source code. Refer to https://source.android.com/source/downloading.html

mkdir android && cd android
repo init -u https://github.com/friendlyarm/android_manifest.git -b nanopi2-lollipop-mr1
repo sync

The "android" directory is the working directory.

If you want to try Android4.4's source code you can run the following commands:

mkdir android && cd android
repo init -u https://github.com/friendlyarm/android_manifest.git -b nanopi2-kitkat
repo sync

Option "-b" specifies a branch

  • Compile System Package
source build/envsetup.sh
lunch aosp_nanopi2-userdebug
make -j8

After your compilation succeeds the following files will be generated in the "out/target/product/nanopi2/" directory.

filename partition Description
boot.img boot -
cache.img cache -
userdata.img userdata -
system.img system -
partmap.txt - partition description file
  • Flash Image to SD Card

If you boot your board from an SD card you can copy your new image file to the sd-fuse_nanopi2/android/ directory and flash this image to your SD card with an installation script. For more details refer to #在Linux Desktop下通过脚本制作

  • Flash Image to eMMC

After compiling Android successfully you can flash it to eMMC with either of the following methods
1) fastboot: right after the NanoPC-T2 is booted from eMMC press any key to enter the uboot commandline mode and type in "fastboot"
Connect your board to a host PC running Ubuntu with a USB cable and run the following commands in the PC's terminal:

cd out/target/product/nanopi2
sudo fastboot flash boot boot.img
sudo fastboot flash cache cache.img
sudo fastboot flash userdata userdata.img
sudo fastboot flash system system.img
sudo fastboot reboot

2) Use an SD Card
Copy these files: boot.img, cache.img, userdata.img, system.img, partmap.txt from the out/target/product/nanopi2 directory to your installation SD card's images/android directory and you can use this SD card to flash Android to eMMC

2 Update Log

2.1 Dec-26-2017

  • Released English Version