Difference between revisions of "Template:OpenWrt1"

From FriendlyELEC WiKi
Jump to: navigation, search
(System Login)
(updated by API)
 
(17 intermediate revisions by 4 users not shown)
Line 9: Line 9:
 
{{#switch: {{{1}}}
 
{{#switch: {{{1}}}
 
  | NanoPi-NEO2 =
 
  | NanoPi-NEO2 =
使用串口模块能有效地提升开发效率,以下是串口模块的连接方法:<br>
+
Here is a hardware setup:<br>
接上串口后,您可以选择从串口模块的DC口或者从MicroUSB口 (如果有) 进行供电:<br />
+
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:<br />
 
[[File:PSU-ONECOM-NEO2.jpg|frameless|400px]]<br>
 
[[File:PSU-ONECOM-NEO2.jpg|frameless|400px]]<br>
 
  | NanoPi-NEO =
 
  | NanoPi-NEO =
使用串口模块能有效地提升开发效率,以下是串口模块的连接方法:<br>
+
Here is a hardware setup:<br>
接上串口后,您可以选择从串口模块的DC口或者从MicroUSB口 (如果有) 进行供电:<br />
+
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:<br />
 
[[File:PSU-ONECOM-NEO.jpg|frameless|400px]]<br>
 
[[File:PSU-ONECOM-NEO.jpg|frameless|400px]]<br>
 
  | NanoPi-NEO-Plus2 =
 
  | NanoPi-NEO-Plus2 =
使用串口模块能有效地提升开发效率,以下是串口模块的连接方法:<br>
+
Here is a hardware setup:<br>
接上串口后,您可以选择从串口模块的DC口或者从MicroUSB口 (如果有) 进行供电:<br />
+
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:<br />
 
[[File:PSU-ONECOM-NEO-Plus2.jpg|frameless|400px]]<br>
 
[[File:PSU-ONECOM-NEO-Plus2.jpg|frameless|400px]]<br>
 
  | NanoPi-NEO-Core =
 
  | NanoPi-NEO-Core =
使用串口模块能有效地提升开发效率,以下是串口模块的连接方法:<br>
+
Here is a hardware setup:<br>
接上串口后,您可以选择从串口模块的DC口或者从MicroUSB口 (如果有) 进行供电:<br />
+
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:<br />
 
[[File:PSU-ONECOM-NEO-Core.jpg|frameless|400px]]<br>
 
[[File:PSU-ONECOM-NEO-Core.jpg|frameless|400px]]<br>
 
  | NanoPi-M1 =
 
  | NanoPi-M1 =
使用串口模块能有效地提升开发效率,以下是串口模块的连接方法:<br>
+
Here is a hardware setup:<br>
接上串口后,您可以选择从串口模块的DC口或者从MicroUSB口 (如果有) 进行供电:<br />
+
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:<br />
 
[[File:PSU-ONECOM-M1.jpg|frameless|400px]]<br>
 
[[File:PSU-ONECOM-M1.jpg|frameless|400px]]<br>
 
  | NanoPi-M1-Plus =
 
  | NanoPi-M1-Plus =
使用串口模块能有效地提升开发效率,以下是串口模块的连接方法:<br>
+
Here is a hardware setup:<br>
接上串口后,您可以选择从串口模块的DC口或者从MicroUSB口 (如果有) 进行供电:<br />
+
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:<br />
 
[[File:PSU-ONECOM-NanoPi-M1-Plus.jpg|frameless|400px]]<br>
 
[[File:PSU-ONECOM-NanoPi-M1-Plus.jpg|frameless|400px]]<br>
 
  | NanoPi-A64 =
 
  | NanoPi-A64 =
使用串口模块能有效地提升开发效率,以下是串口模块的连接方法:<br>
+
Here is a hardware setup:<br>
接上串口后,您可以选择从串口模块的DC口或者从MicroUSB口 (如果有) 进行供电:<br />
+
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:<br />
 
[[File:PSU-ONECOM-A64.jpg|frameless|400px]]<br>
 
[[File:PSU-ONECOM-A64.jpg|frameless|400px]]<br>
 
  | NanoPi-NEO-Air =
 
  | NanoPi-NEO-Air =
使用串口模块能有效地提升开发效率,以下是串口模块的连接方法:<br>
+
Here is a hardware setup:<br>
接上串口后,您可以选择从串口模块的DC口或者从MicroUSB口 (如果有) 进行供电:<br />
+
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:<br />
 
[[File:PSU-ONECOM-AIR.jpg|frameless|400px]]<br>
 
[[File:PSU-ONECOM-AIR.jpg|frameless|400px]]<br>
 
  | NanoPi-R1 =
 
  | NanoPi-R1 =
使用串口模块能有效地提升开发效率,以下是串口模块的连接方法:<br>
+
Here is a hardware setup:<br>
接上串口后,请注意串口模块的DC口和NanoPi-R1的MicroUSB口都需要供电:<br />
+
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:<br />
 
[[File:PSU-ONECOM-R1.jpg|frameless|500px]]<br>
 
[[File:PSU-ONECOM-R1.jpg|frameless|500px]]<br>
 +
| NanoPi-R1S-H3 =
 +
Here is a hardware setup:<br>
 +
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:<br />
 +
[[File:PSU-ONECOM-R1S.jpg|frameless|500px]]<br>
 +
| NanoPi-R1S-H5 =
 +
Here is a hardware setup:<br>
 +
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:<br />
 +
[[File:PSU-ONECOM-R1S.jpg|frameless|500px]]<br>
 +
| NanoPi-NEO2-Black =
 +
Here is a hardware setup:<br>
 +
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:<br />
 +
[[File:PSU-ONECOM-NEO2-Black.jpg|frameless|500px]]<br>
 
  | NanoPi-Duo =
 
  | NanoPi-Duo =
 
  | NanoPi-Duo2 =
 
  | NanoPi-Duo2 =
 
     <!-- Duox not support ONECOM -->
 
     <!-- Duox not support ONECOM -->
 
  | #default =
 
  | #default =
使用串口模块能有效地提升开发效率,以下是串口模块的连接方法:<br>
+
Here is a hardware setup:<br>
接上串口后,您可以选择从串口模块的DC口或者从MicroUSB口 (如果有) 进行供电。
+
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:}}
}}
+
  
 
{{#switch: {{{1}}}
 
{{#switch: {{{1}}}
 
  | NanoPC-T4 =
 
  | NanoPC-T4 =
{{{1}}}需要使用USB转串口模块,连接方法如下图所示:<br>[[File:T4usb2serialport.jpg|frameless|500px]]<br>
+
{{{1}}}you need to use a USB to serial board and here is a hardware setup:<br>[[File:T4usb2serialport.jpg|frameless|500px]]<br>
 
  | NanoPi-M4 =
 
  | NanoPi-M4 =
{{{1}}}需要使用USB转串口模块,连接方法如下图所示:<br>[[File:m4usb2serialport.jpg|frameless|500px]]<br>
+
{{{1}}}you need to use a USB to serial board and here is a hardware setup:<br>[[File:m4usb2serialport.jpg|frameless|500px]]<br>
 +
| NanoPi-M4V2 =
 +
{{{1}}}you need to use a USB to serial board and here is a hardware setup:<br>[[File:m4usb2serialport.jpg|frameless|500px]]<br>
 +
| NanoPi-M4B =
 +
{{{1}}}you need to use a USB to serial board and here is a hardware setup:<br>[[File:m4usb2serialport.jpg|frameless|500px]]<br>
 
  | NanoPi-NEO4 =  
 
  | NanoPi-NEO4 =  
{{{1}}}需要使用USB转串口模块,连接方法如下图所示:<br>[[File:neo4usb2serialport.jpg|frameless|500px]]<br>
+
{{{1}}}you need to use a USB to serial board and here is a hardware setup:<br>[[File:neo4usb2serialport.jpg|frameless|500px]]<br>
 
  | NanoPi-NEO2 =
 
  | NanoPi-NEO2 =
也可以使用USB转串口模块调试,请注意需要使用5V/2A电源给开发板MicroUSB供电:<br>
+
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power:<br>
 
[[File:USB2UART-NEO2.jpg|frameless|400px]]<br>
 
[[File:USB2UART-NEO2.jpg|frameless|400px]]<br>
 
  | NanoPi-NEO-Core =
 
  | NanoPi-NEO-Core =
也可以使用USB转串口模块调试,请注意需要使用5V/2A电源给开发板MicroUSB供电:<br>
+
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power:<br>
 
[[File:USB2UART-NEO-Core.jpg|frameless|400px]]<br>
 
[[File:USB2UART-NEO-Core.jpg|frameless|400px]]<br>
 
  | NanoPi-M1 =
 
  | NanoPi-M1 =
也可以使用USB转串口模块调试,请注意需要使用5V/2A电源给开发板MicroUSB供电:<br>
+
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power:<br>
 
[[File:USB2UART-M1.jpg|frameless|400px]]<br>
 
[[File:USB2UART-M1.jpg|frameless|400px]]<br>
 
| NanoPi-M1-Plus =
 
| NanoPi-M1-Plus =
也可以使用USB转串口模块调试,请注意需要使用5V/2A电源给开发板MicroUSB供电:<br>
+
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power:<br>
 
[[File:USB2UART-M1-Plus.jpg|frameless|400px]]<br>
 
[[File:USB2UART-M1-Plus.jpg|frameless|400px]]<br>
 
  | NanoPi-Duo =
 
  | NanoPi-Duo =
使用USB转串口模块调试,请注意需要使用5V/2A电源给开发板MicroUSB供电:<br>
+
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power:<br>
 
[[File:USB2UART-Duo.jpg|frameless|400px]]<br>
 
[[File:USB2UART-Duo.jpg|frameless|400px]]<br>
 
| NanoPi-Duo2 =
 
| NanoPi-Duo2 =
使用USB转串口模块调试,请注意需要使用5V/2A电源给开发板MicroUSB供电:<br>
+
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power:<br>
 
[[File:USB2UART-Duo2.jpg|frameless|400px]]<br>
 
[[File:USB2UART-Duo2.jpg|frameless|400px]]<br>
 
  | NanoPi-NEO-Plus2 =
 
  | NanoPi-NEO-Plus2 =
也可以使用USB转串口模块调试,请注意需要使用5V/2A电源给开发板MicroUSB供电:<br>
+
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power:<br>
 
[[File:USB2UART-NEO-Plus2.jpg|frameless|400px]]<br>
 
[[File:USB2UART-NEO-Plus2.jpg|frameless|400px]]<br>
 
  | NanoPi-NEO =
 
  | NanoPi-NEO =
也可以使用USB转串口模块调试,请注意需要使用5V/2A电源给开发板MicroUSB供电:<br>
+
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power:<br>
 
[[File:Matrix-USB2UART_nanopi_NEO.jpg|frameless|400px]]<br>
 
[[File:Matrix-USB2UART_nanopi_NEO.jpg|frameless|400px]]<br>
 
  | NanoPi-NEO-Air =
 
  | NanoPi-NEO-Air =
也可以使用USB转串口模块调试,请注意需要使用5V/2A电源给开发板MicroUSB供电:<br>
+
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power:<br>
 
[[File:Matrix-USB2UART_NEO_Air.jpg|frameless|500px]]<br>
 
[[File:Matrix-USB2UART_NEO_Air.jpg|frameless|500px]]<br>
 
  | NanoPi-R1 =
 
  | NanoPi-R1 =
也可以使用USB转串口模块调试,请注意需要使用5V/2A电源给开发板MicroUSB供电:<br>
+
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power:<br>
 
[[File:Matrix-USB2UART_nanopi_R1.jpg|frameless|500px]]<br>
 
[[File:Matrix-USB2UART_nanopi_R1.jpg|frameless|500px]]<br>
 +
| NanoPi-R1S-H3 =
 +
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power:<br>
 +
[[File:Matrix-USB2UART_nanopi_R1S-H3.jpg|frameless|500px]]<br>
 +
| NanoPi-R1S-H5 =
 +
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power:<br>
 +
[[File:Matrix-USB2UART_nanopi_R1S-H3.jpg|frameless|500px]]<br>
 +
| NanoPi-NEO2-Black =
 +
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power:<br>
 +
[[File:Matrix-USB2UART_nanopi_NEO2-Black.jpg|frameless|500px]]<br>
 
  | #default =
 
  | #default =
也可以使用USB转串口模块调试,请注意需要使用5V/2A电源给开发板MicroUSB供电。
+
or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power.
 
}}
 
}}
  
默认会以 root 用户自动登录,并且没有设置root用户的密码,你可以使用 passwd 命令来设置 root 用户的密码。<br />
+
By default you will login as root without a password. You can use "passwd" to set a password for root.<br />
 
[[File:op_login.jpg|frameless|500px|op_login]]<br>
 
[[File:op_login.jpg|frameless|500px|op_login]]<br>
第一次运行系统时,系统会自动拓展TF卡上文件系统分区到最大可用空间:<br>
+
On first boot the system will automatically extend the file system on the TF card to the max capacity:<br>
 
[[File:resize_rootfs_userdata.png|frameless|500px|resize_rootfs_userdata]]<br>
 
[[File:resize_rootfs_userdata.png|frameless|500px|resize_rootfs_userdata]]<br>
请耐心等待文件系统扩展完成。
+
Please wait for this to be done.
  
* <strong>SSH登录</strong>
+
* <strong>Login via SSH</strong>
 
{{#switch: {{{1}}}
 
{{#switch: {{{1}}}
 
  | NanoPi-R1
 
  | NanoPi-R1
 +
| NanoPi-R1S-H3
 +
| NanoPi-R1S-H5
 
  | NanoPi-M1-Plus
 
  | NanoPi-M1-Plus
 
  | NanoPi-M1
 
  | NanoPi-M1
Line 109: Line 135:
 
  | NanoPi-NEO-Core2
 
  | NanoPi-NEO-Core2
 
  | NanoPi-NEO-Plus2
 
  | NanoPi-NEO-Plus2
  | NanoPi-NEO2 =
+
  | NanoPi-NEO2
在本开发板的OpenWrt系统里,有线网络(eth0) 被配置为WAN功能。<br>
+
| NanoPi-NEO2-Black =
启动系统前,请先用网线连接板子的有线以太网口到一级路由器的LAN口,以便该以太网(eth0) 能通过DHCP获取到IP地址。<br>
+
In FriendlyElec's OpenWrt system the Ethernet(eth0) is configured as WAN.<br>
这里假设已经通过调试串口或者一级路由器确定板子的以太网(eth0) 的IP地址为192.168.1.163,执行下列命令通过SSH登录系统:
+
Before power on your board make sure your board is connected to a master router's LAN with an Ethernet cable and the eth0 will be assigned an IP address by DHCP.<br>
 +
For example, if your eth0 is assigned an IP address 192.168.1.163 you can login with SSH by running the following command:
 
<syntaxhighlight lang="text">
 
<syntaxhighlight lang="text">
 
$ ssh root@192.168.1.163
 
$ ssh root@192.168.1.163
 
</syntaxhighlight>
 
</syntaxhighlight>
无需密码,直接就可以登录。
+
You can login without a password.
 
| NanoPi-NEO-Air
 
| NanoPi-NEO-Air
 
| NanoPi-Duo2
 
| NanoPi-Duo2
 
| NanoPi-Duo =  
 
| NanoPi-Duo =  
本开发板的OpenWrt系统默认的WiFi AP热点名称类似为“OpenWrt-10:d0:7a:de:3d:92”,网段为192.168.2.x,没有密码,可用手机或者PC机连接该热点,然后执行下列命令SSH登录系统:
+
By default in FriendlyElec's OpenWrt system the WiFi AP hotspot's name is like "OpenWrt-10:d0:7a:de:3d:92" and the network segment is 192.168.2.x. You can connect your device to it and login with SSH without a password by running the following command:
 
<syntaxhighlight lang="text">
 
<syntaxhighlight lang="text">
 
$ ssh root@192.168.2.1
 
$ ssh root@192.168.2.1
 
</syntaxhighlight>
 
</syntaxhighlight>
无需密码,直接就可以登录。
+
You can login without a password.
 
}}
 
}}
  
* <strong>Web登录</strong>
+
* <strong>Login via Web</strong>
OpenWrt系统支持通过LuCI Web界面进行访问和配置。<br>
+
You can login OpenWrt via a LuCI Web page.<br>
 
{{#switch: {{{1}}}
 
{{#switch: {{{1}}}
 
  | NanoPi-R1
 
  | NanoPi-R1
 +
| NanoPi-R1S-H3
 +
| NanoPi-R1S-H5
 
  | NanoPi-M1-Plus
 
  | NanoPi-M1-Plus
 
  | NanoPi-M1
 
  | NanoPi-M1
Line 138: Line 167:
 
  | NanoPi-NEO-Core2
 
  | NanoPi-NEO-Core2
 
  | NanoPi-NEO-Plus2
 
  | NanoPi-NEO-Plus2
  | NanoPi-NEO2 =
+
  | NanoPi-NEO2
在已完成 <SSH登录> 章节里的设置的基础上,假设板子的有线以太网的IP地址为192.168.1.163,在浏览器中输入该IP地址就可以登录OpenWrt-LuCI界面了:<br>
+
| NanoPi-NEO2-Black =
 +
After you go through all the steps in <Login via SSH> and get an IP address e.g. 192.168.1.163 for the Ethernet connection, type this IP address in a browser's address bar and you will be able to login OpenWrt-LuCI:<br>
 
[[File:R1-OpenWrt-LuCI.jpg|frameless|600px|R1-OpenWrt-LuCI]]<br>
 
[[File:R1-OpenWrt-LuCI.jpg|frameless|600px|R1-OpenWrt-LuCI]]<br>
 
  | NanoPi-NEO-Air
 
  | NanoPi-NEO-Air
 
  | NanoPi-Duo2
 
  | NanoPi-Duo2
 
  | NanoPi-Duo =  
 
  | NanoPi-Duo =  
在已完成<SSH登录>章节里的设置的基础上,在浏览器中输入 192.168.2.1 就可以登录OpenWrt-LuCI界面了:<br>
+
After you go through all the steps in <Login via SSH> and get an IP address e.g. 192.168.2.1 for the Ethernet connection, type this IP address in a browser's address bar and you will be able to login OpenWrt-LuCI:<br>
 
[[File:OpenWrt-LuCI_wlan0.jpg|frameless|600px|OpenWrt-LuCI_wlan0]]<br>
 
[[File:OpenWrt-LuCI_wlan0.jpg|frameless|600px|OpenWrt-LuCI_wlan0]]<br>
 
}}
 
}}
默认用户名为root,无需密码,直接点击"Login"按键即可登录。
+
By default you will login as root without a password, just click on "Login" to login.
  
 
===Manage Software Packages===
 
===Manage Software Packages===
Line 269: Line 299:
 
{{#switch: {{{1}}}
 
{{#switch: {{{1}}}
 
  | NanoPi-R1
 
  | NanoPi-R1
 +
| NanoPi-R1S-H3
 +
| NanoPi-R1S-H5
 
  | NanoPi-M1-Plus
 
  | NanoPi-M1-Plus
 
  | NanoPi-NEO-Plus2
 
  | NanoPi-NEO-Plus2
Line 279: Line 311:
 
  | NanoPi-NEO-Core
 
  | NanoPi-NEO-Core
 
  | NanoPi-NEO-Core2
 
  | NanoPi-NEO-Core2
  | NanoPi-NEO2 =
+
  | NanoPi-NEO2
 +
| NanoPi-NEO2-Black =
 
  [[File:op_interface_eth0.png|frameless|600px|op_interface_eth0]] <br>
 
  [[File:op_interface_eth0.png|frameless|600px|op_interface_eth0]] <br>
 
  | NanoPi-NEO-Air =
 
  | NanoPi-NEO-Air =
Line 288: Line 321:
 
{{#switch: {{{1}}}
 
{{#switch: {{{1}}}
 
  | NanoPi-R1
 
  | NanoPi-R1
 +
| NanoPi-R1S-H3
 +
| NanoPi-R1S-H5
 
  | NanoPi-M1-Plus
 
  | NanoPi-M1-Plus
 
  | NanoPi-NEO-Plus2
 
  | NanoPi-NEO-Plus2
Line 301: Line 336:
  
 
{{#switch: {{{1}}}
 
{{#switch: {{{1}}}
  | NanoPi-R1 =
+
  | NanoPi-R1  
 +
| NanoPi-R1S-H3
 +
| NanoPi-R1S-H5 =
 
===Check LED Configurations===
 
===Check LED Configurations===
 
* After open the OpenWrt-LuCI page, go to System ---> LED Configuration and you will see the LED's configurations: <br>
 
* After open the OpenWrt-LuCI page, go to System ---> LED Configuration and you will see the LED's configurations: <br>
Line 314: Line 351:
  
 
{{#switch: {{{1}}}
 
{{#switch: {{{1}}}
  | NanoPi-R1 =
+
  | NanoPi-R1  
 +
| NanoPi-R1S-H3
 +
| NanoPi-R1S-H5 =
 
===Check BUTTON Configurations===
 
===Check BUTTON Configurations===
 
FriendlyElec's OpenWrt system uses the triggerhappy utility to configure BUTTON's functions. By default when BUTTON is pressed a reboot will be triggered.
 
FriendlyElec's OpenWrt system uses the triggerhappy utility to configure BUTTON's functions. By default when BUTTON is pressed a reboot will be triggered.
Line 323: Line 362:
 
** [https://openwrt.org/docs/guide-user/hardware/hardware.button openwrt hardware.button]
 
** [https://openwrt.org/docs/guide-user/hardware/hardware.button openwrt hardware.button]
 
}}
 
}}
 +
 +
===USB WiFi===
 +
Currently the NanoPi NEO2 Black only works with a RTL8821CU USB WiFi dongle, plug and play. After this module is connected to the board it will by default work under AP mode and the hotspot's name is "rtl8821cu-mac address" and the password is "password";
 +
 +
===Huawei's WiFi 2 mini(E8372H-155) Module===
 +
After this module is connected to the board it will be plug and play. The hotspot's name is "HUAWEI-8DA5". You can connect a device to the internet by connecting to this hotspot.

Latest revision as of 06:35, 27 November 2019

1 Work with OpenWrt

1.1 Introduction

OpenWrt is a highly extensible GNU/Linux distribution for embedded devices.Unlike many other distributions for routers, OpenWrt is built from the ground up to be a full-featured, easily modifiable operating system for embedded devices. In practice, this means that you can have all the features you need with none of the bloat, powered by a modern Linux kernel. For more details you can refer to:OpenWrt Website.

1.2 System Login

  • Login via Serial Port

When you do kernel development you'd better get a serial communication board. After you connect your board to a serial communication board you will be able to do development work from a commandline utility.
Here is a hardware setup:
After you connect your board to a serial communication board (e.g. FriendlyElec's serial communication board) you can power the whole system from either the DC port on the serial communication board or the MicroUSB port(if there is one) on your board:

or you can use a USB to serial board and power on the whole system at the MicroUSB port with a 5V/2A power.

By default you will login as root without a password. You can use "passwd" to set a password for root.
op_login
On first boot the system will automatically extend the file system on the TF card to the max capacity:
resize_rootfs_userdata
Please wait for this to be done.

  • Login via SSH


  • Login via Web

You can login OpenWrt via a LuCI Web page.

By default you will login as root without a password, just click on "Login" to login.

1.3 Manage Software Packages

OpenWrt has a package management utility: opkg. You can get its details by running the following command:

$ opkg
Package Manipulation:
        update                  Update list of available packages
        upgrade <pkgs>          Upgrade packages
        install <pkgs>          Install package(s)
        configure <pkgs>        Configure unpacked package(s)
        remove <pkgs|regexp>    Remove package(s)
        flag <flag> <pkgs>      Flag package(s)
         <flag>=hold|noprune|user|ok|installed|unpacked (one per invocation)
 
Informational Commands:
        list                    List available packages
        list-installed          List installed packages
        list-upgradable         List installed and upgradable packages
        list-changed-conffiles  List user modified configuration files
        files <pkg>             List files belonging to <pkg>
        search <file|regexp>    List package providing <file>
        find <regexp>           List packages whose name or description matches <regexp>
        info [pkg|regexp]       Display all info for <pkg>
        status [pkg|regexp]     Display all status for <pkg>
        download <pkg>          Download <pkg> to current directory
...

These are just part of the manual. Here are some popular opkg commands.

  • Update Package List

Before you install a package you'd better update the package list:

$ opkg update
  • Check Available Packages
$ opkg list

At the time of writing there are 3241 packages available.

  • Check Installed Packages:
$ opkg list-installed

At the time of writing 124 packages have been installed.

  • Install/Delete Packages:
$ opkg install <pkgs>
$ opkg remove <pkgs>
  • Check Files Contained in Installed Packages:
$ opkg files <pkg>
  • Install Chinese Language Package for LuCI
$ opkg install luci-i18n-base-zh-cn
  • Check Changed Files:
$ opkg list-changed-conffiles

1.4 Check System Status

  • Check CPU Temperature & Frequency via Commandline
$ cpu_freq 
Aavailable frequency(KHz):
        480000 624000 816000 1008000
Current frequency(KHz):
        CPU0 online=1 temp=26548C governor=ondemand freq=624000KHz
        CPU1 online=1 temp=26548C governor=ondemand freq=624000KHz
        CPU2 online=1 temp=26548C governor=ondemand freq=624000KHz
        CPU3 online=1 temp=26548C governor=ondemand freq=624000KHz

These messages mean that there are four CPU cores working online simultaneously. Each core's temperature is 26.5 degrees in Celsius, the scheduling policy is on-demand and the working frequency is 624MHz. You can set the frequency by running the following command:

$ cpu_freq -s 1008000
Aavailable frequency(KHz):
        480000 624000 816000 1008000
Current frequency(KHz):
        CPU0 online=1 temp=36702C governor=userspace freq=1008000KHz
        CPU1 online=1 temp=36702C governor=userspace freq=1008000KHz
        CPU2 online=1 temp=36702C governor=userspace freq=1008000KHz
        CPU3 online=1 temp=36702C governor=userspace freq=1008000KHz

These messages mean four CPU cores are working online. Each core's temperature is 26.5 degrees. Each core's governor is on demand and the frequency is 480 MHz.

  • Check System Status on OpenWrt-LuCI Web Page

After open the OpenWrt-LuCI page, go to "Statistics ---> Graphs" and you will see various system statistics e.g.:
1) System Load:
statistics_system_load
2) RAM:
statistics_memory
3) CPU Temperature:
statistics_thermal
All the statistics listed on the Statistics page are presented by the luci-app-statistics package which uses the Collectd utility to collect data and presents them with the RRDtool utility.
If you want to get more statistics you can install other collectd-mod-* packages. All collectd-mod-* packages use the same configuration file: /etc/config/luci_statistics.

1.5 Check Network->Interfaces Configurations

  • After open the OpenWrt-LuCI page, go to "Network" ---> "Interfaces" and you will see the current network's configurations:
  • All the configurations listed on the Network->Interfaces page are stored in the "/etc/config/network" file.




1.6 USB WiFi

Currently the NanoPi NEO2 Black only works with a RTL8821CU USB WiFi dongle, plug and play. After this module is connected to the board it will by default work under AP mode and the hotspot's name is "rtl8821cu-mac address" and the password is "password";

1.7 Huawei's WiFi 2 mini(E8372H-155) Module

After this module is connected to the board it will be plug and play. The hotspot's name is "HUAWEI-8DA5". You can connect a device to the internet by connecting to this hotspot.