Difference between revisions of "Template:BurnLinuxToSD-Allwinner/zh"

From FriendlyELEC WiKi
Jump to: navigation, search
(Install Linux)
(updated by API)
 
Line 1: Line 1:
====Install Linux====
+
====烧写Linux系统====
=====Flash to TF Card=====
+
=====烧写到TF卡=====
* FriendlyCore / FriendlyWrt are both based on Linux distributions and their installation methods are the same.<br>
+
* FriendlyCore / FriendlyWrt 等系统都属于 Linux 系统,所以它们的烧写方法是一样。<br>
* Extract the Linux image and win32diskimager.rar files. Insert a TF card(at least 8G) into a Windows PC and run the win32diskimager utility as administrator. On the utility's main window select your TF card's drive, the wanted image file and click on "write" to start flashing the TF card.
+
* Linux 系统固件和烧写工具 win32diskimager.rar 分别解压,在 Windows 下插入TF卡(限4G及以上的卡),以管理员身份运行烧写工具  win32diskimager,在烧写工具  win32diskimager 的界面上,选择你的TF卡盘符,选择Linux 系统固件,点击 Write 按钮烧写。
  
 
{{#switch: {{{2}}}
 
{{#switch: {{{2}}}
 
| h3 =  
 
| h3 =  
Take {{#replace:{{lc:{{{1}}}}}|category:|}}_sd_friendlycore-xenial_4.14_armhf_YYYYMMDD.img as an example here is the installation window. Other image files are installed on the similar window:<br>
+
这里以{{#replace:{{lc:{{{1}}}}}|category:|}}_sd_friendlycore-xenial_4.14_armhf_YYYYMMDD.img为例,其他系统的烧写操作是类似的,烧写时的界面如下:<br>
 
[[File:win32disk-h3.jpg|frameless|600px|win32disk-h3]]<br>
 
[[File:win32disk-h3.jpg|frameless|600px|win32disk-h3]]<br>
 
| h5 =  
 
| h5 =  
Take {{#replace:{{lc:{{{1}}}}}|category:|}}_sd_friendlycore-xenial_4.14_arm64_YYYYMMDD.img as an example here is the installation window. Other image files are installed on the similar window:<br>
+
这里以{{#replace:{{lc:{{{1}}}}}|category:|}}_sd_friendlycore-xenial_4.14_arm64_YYYYMMDD.img为例,其他Linux系统的烧写操作是类似的,烧写时的界面如下:<br>
 
[[File:win32disk-h5.jpg|frameless|600px|win32disk-h5]]<br>
 
[[File:win32disk-h5.jpg|frameless|600px|win32disk-h5]]<br>
 
}}
 
}}
  
After it is installed you will see the following window:<br>
+
成功烧写后,会看到如下界面:<br>
 
[[File:win32disk-finish.jpg|frameless|600px|win32disk-finish]]<br>
 
[[File:win32disk-finish.jpg|frameless|600px|win32disk-finish]]<br>
  
* Insert this card into your board's BOOT slot and power on (with a 5V/2A power source). If the PWR LED is on and the STAT LED is blinking this indicates your board has successfully booted.
+
*当制作完成TF卡后,拔出TF卡插入 BOOT 卡槽,上电启动(注意,这里需要5V/2A的供电),你可以看到STAT灯闪烁,这时你已经成功启动系统。

Latest revision as of 09:27, 10 February 2020

1 烧写Linux系统

1.1 烧写到TF卡
  • FriendlyCore / FriendlyWrt 等系统都属于 Linux 系统,所以它们的烧写方法是一样。
  • 将 Linux 系统固件和烧写工具 win32diskimager.rar 分别解压,在 Windows 下插入TF卡(限4G及以上的卡),以管理员身份运行烧写工具 win32diskimager,在烧写工具 win32diskimager 的界面上,选择你的TF卡盘符,选择Linux 系统固件,点击 Write 按钮烧写。


成功烧写后,会看到如下界面:
win32disk-finish

  • 当制作完成TF卡后,拔出TF卡插入 BOOT 卡槽,上电启动(注意,这里需要5V/2A的供电),你可以看到STAT灯闪烁,这时你已经成功启动系统。