Smart4418/6818SDK V2

From FriendlyELEC WiKi
Revision as of 07:10, 25 June 2019 by Kangjing (Talk | contribs) (Resources)

Jump to: navigation, search

查看中文

1 Introduction

Overview
Front
Back
  • The Smart4418/6818SDK V2 carrier board populates popular interface pins from the the Smart4418/6818 CPU board. These interface pins include HDMI, USB Host, MicroSD card slot, RS-233 port, RS-485 port, RJ-45 Ethernet port, 3.5mm audio input and output, 4G module interface, MicroSIM card slot etc. It has some onboard hardware resources such as buzzer, buttons, RTC battery holder, microphone etc. All the popular interfaces and ports are on the same side. This layout makes it easy for customers to make a customized case for it. This carrier board can work with FriendlyElec's various LCDs such as HD702, HD702V, S430 LCD etc.
  • In order for users to test and develop prototypes this Smart4418/6818SDK carrier board also populates DVP camera interface, SPI, GPIO, I2C, UART and has onboard AP6212 WiFi module, PCB antenna, IPX interface, RTC battery holder. Users can easily connect various devices to this board for testing. This meets the requirements for fast prototyping in various industrial applications.
  • The Smart4418/6818SDK V2 carrier board has both RGB LCD interface and LVDS LCD interface. It can work with FriendlyElec's HD702 LCD, HD702V LCD,S430 LCD. Its RGB LCD pin-header interface and LVDS LCD pin-header interface can be used to test other LCDs as well.

2 Hardware Spec

Features
Carrier Board Type Smart4418/6818SDK V2
Dimension 185 x 123(mm)
Applicable Smart4418
Wi-Fi/Bluetooth Onboard Wi-Fi Bluetooth module, PCB antenna and IPX Wi-Fi antenna interface
MiniPCIe Interface 4G module, only for text message, no voice service, onboard IPX to SMA antenna interface
SIM Card Slot Pop-up MicroSIM card slot
DVP Camera Interface 24pin, 0.5mm pitch, FPC seat
DVP Camera interface, ITU-R BT 601/656 8-bit
HDMI Output 1 x HDMI A Type, supports HDMI 1.4a(Smart4418)
supports 1080p 30-frame video output
TTL Serial Port 1 x 3-wire serial port (UART0), 2.54mm pitch connector, it is by default used as a debug serial port
RS-485 Serial Port 1 x 3-wire serial port (UART2), 5.08mm pitch connector
RS-232 Serial Port 1 x 3-wire serial port (UART3), DB9 male connector
USB Host 3 x USB port, populated from USB 2.0 hub(compatible with USB 1.1)
2 x USB type A port, 1 x 2.0mm pitch PH-4A connector
USB Slave 1 x MicroUSB port, only for data transmission
Audio Input and Output populated from Smart4418/Smart6818 CPU board
supports audio recording and play
3.5mm audio jack and MIC input
2Pin 2.54mm pitch MIC pin-header
Ethernet populated from Smart4418/Smart6818 CPU board, 1000/100/10M
Button PWRKEY(power button)
RST(reset button)
K1/K2/K3 programmable buttons
LED 2 x GPIO programmable LED(on Smart4418/Smart6818 CPU board)
RTC Battery holder Onboard RTC battery holder (CR2032)
Buzzer 1 x PWM buzzer
SPI 2 x SPI interface(SPI0, SPI1), 2.0mm pitch PH-6A connector
it can be used as GPIO pins
MicroSD Card Slot pop-up MicroSD card slot
I2C 2 x I2C0 interface, 2.0mm pitch PH-4A connector
RGB LCD Interface RGB LCD interface(45pin, 0.5mm pitch FPC seat)
supports FriendlyElec's one-wire touch technology
supports backlight control
supports capacitive touch panel
supports RGB888
supports full-color TFT LCD
populated to 22 x 2Pin 2.0mm pitch pin-header
LVDS Interface LVDS LCD interface(24pin, 0.5mm pitch FPC seat)
i2c touch panel
supports backlight control
supports capacitive touch panel
populated to 10 x 2 Pin 2.0mm pitch pin-header
LVDS power interface 2.0mm pitch PH-6A connector, it works as power input for LVDS
LCD Mounting Hole applicable for FriendlyElec's HD702, HD702V and S430 LCD etc
Other Resources 1 x Onboard EEPROM, 1 x 3-Axis Digital Accelerometer
4 x 2Pin 2.54mm pitch pin-header,includes 1 x 3.3V, 1 x boot selection used to select boot from eMMC or MicroSD(HIGH means booting from eMMC and LOW means booting from MicroSD), 1 x RST, 1 x PWRKEY, 4 x GND
Power Supply DC 9V~15V/2A, when use LVDS to control backlight it is recommended to use a 12V/3A power supply

3 Diagram, Layout and Dimension

3.1 Layout

  • RGB LCD Interface(on the back side of the carrier board, 0.5mm pitch 44Pin FPC seat)
Pin# Name Description
1, 2 VDD_5V 5V output, used to power LCD
11,20,29,37,38,39,40,45 DGND Ground
3-10 Blue LSB to MSB RGB blue
12-19 Green LSB to MSB RGB green
21-28 Red LSB to MSB RGB red
30 GPIOB25 GPIO pin, available for users
31 GPIOC15 used to detect LCD type

used for backlight control and resistive touch panel. Users cannot change it.

33 VDEN indicates whether RGB signals are valid
34 VSYNC vertical synchronization
35 HSYNC horizontal synchronization
36 LCDCLK LCD clock, Pixel frequency
41 I2C2_SCL I2C2's clock. It transmits capacitive touch panel's signals
42 I2C2_SDA I2C2's data. It transmits capacitive touch panel's data
43 GPIOC16 capacitive touch panel's interrupt. It should work in conjunction with I2C2
32, 44 NC Not connected
  • LVDS LCD Interface(on the back of the carrier board, 0.5mm pitch 24-Pin FPC seat)
Pin# Name Description
1-3 VDD_5V 5V power output, used to power LCD module
6,9,12,15,18,24 GND Ground
4 LVDS_D0- LVDS D0 negative output
5 LVDS_D0+ LVDS D0 positive output
7 LVDS_D1- LVDS D1 negative output
8 LVDS_D1+ LVDS D1 positive output
10 LVDS_D2- LVDS D2 negative output
11 LVDS_D2+ LVDS D2 positive output
13 LVDS_CLK- LVDS CLK negative output
14 LVDS_CLK+ LVDS CLK positive output
16 LVDS_D3- LVDS D3 negative output
17 LVDS_D3+ LVDS D3 positive output
19, 20 NC Not connected
21 I2C2_SCL I2C2 clock, it transmits capacitive touch panel's signal
22 I2C2_SDA I2C2 data, it transmits capacitive touch panel's data
23 GPIOC16 capacitive touch panel's interrupt. It should work in conjunction with I2C2
  • RGB LCD Interface(on the front side of the carrier board, 2.0mm pitch 22 x 2 Pin header)
Pin# Name Description
1, 2 VDD_5V 5V power output, used to power LCD module
11,20,29,37,38,39,40 DGND Ground
3-10 Blue LSB to MSB RGB blue
12-19 Green LSB to MSB RGB green
21-28 Red LSB to MSB RGB red
30 GPIOB25 GPIO pin, available for users
31 GPIOC15 used to detect LCD type

used for backlight control and resistive touch panel. Users cannot change it.

33 VDEN indicates whether RGB signals are valid.
34 VSYNC vertical synchronization
35 HSYNC horizontal synchronization
36 LCDCLK LCD clock, Pixel frequency
41 I2C2_SCL I2C2 signal, it transmits capacitive touch panel's signals
42 I2C2_SDA I2C2 data, it transmits capacitive touch panel's data
43 GPIOC16 capacitive touch panel's interrupt, it should work in conjunction with I2C2
32, 44 NC Not connected
  • LVDS Interface(on the front side of the carrier board, 2.0mm pitch 10 x 2 Pin header)
Pin# Name Pin# Name
1 SYS_3.3V 2 SYS_3.3V
3 GPIOC16 4 GPIOB18
5 DGND 6 DGND
7 LVDS_D0- 8 LVDS_D0+
9 LVDS_D1- 10 LVDS_D1+
11 LVDS_D2- 12 LVDS_D2+
13 DGND 14 DGND
15 LVDS_CLK- 16 LVDS_CLK+
17 LVDS_D3- 18 LVDS_D3+
19 I2C2_SCL 20 I2C2_SDA
  • LVDS Power Interface(on the front side of the carrier board, 2.0mm pitch 6Pin PH-6A connector)
Pin# Name
1,2 VDD_12V
3 GPIOB18
4 NC
5, 6 DGND
  • DVP Camera Interface
Pin# Name
1, 2 SYS_3.3V
7,9,13,15,24 DGND
3 I2C0_SCL
4 I2C0_SDA
5 GPIOB14
6 GPIOB16
8,10 NC
11 VSYNC
12 HREF
14 PCLK
16-23 Data bit7-0
  • Power Port
  • DC power port, applicable for DC 5.5 * 2.1mm power plug, 9V ~ 15V voltage input. The LVDS' backlight takes power directly from the power port. When you need to control the LVDS' backlight it is recommended to use a 12V/3A power input
DC-005.png

3.2 Board Dimension

Smart4418 6818SDK V2 1812-Dimensions

For more details refer to: [http:xf%29.zip Smart4418/6818SDK V2 1812 dxf file]

4 Applicable External Modules

1. The Smart4418/6818SDK V2 carrier board can work with the Smart4418 and Smart6818 CPU board.

Connected to EC20 4G Module Connected to S430 LCD Connected to HD702V LCD

5 Resources

  • Smart4418/6818SDK V2 Hardware Documents
Smart4418/6818SDK V2 1903 schematics file, Capture 16.5 or above
Smart4418/6818SDK V2 1903 PCB file, Allegro 16.5 or above
Smart4418/6818SDK V2 1812 PCB dxf file
Smart4418/6818SDK V2 1812 schematics in pdf
  • Smart4418 CPU Board Hardware Documents
Smart4418 CPU board's wiki
Smart4418 schematics in pdf

6 Update Log

6.1 Jan-22-2019

  • Released English version.