NanoPi NEO Plus2

查看中文

1 Introduction

Overview

Front

Back

• The NanoPi NEO Plus2 is another Allwinner based ARM board developed by FriendlyElec. It uses Allwinner's 64-bit quad-core A53 SoC with hexa-core Mali450 GPU and features 1GB of DDR3 RAM and 8GB eMMC.
• With a small size of only 40 x 52mm the NanoPi NEO Plus2 has rich on-board resources: AP6212A WiFi & Bluetooth module, Gbps Ethernet and two USB hosts. It supports system-boot from a MicroSD card.
• The NanoPi NEO Plus2 has a carefully designed power system and 6-layer PCB layout. These features enhance the board's heat dissipation.
• The NanoPi NEO Plus2 meets popular IOT applications requirements for small size, high-speed and large throughput data transmission and high performance computing.

2 Hardware Spec

• SoC: Allwinner H5，Quad-core 64-bit high-performance Cortex A53
• DDR3 RAM:1GB
• Storage: 8GB eMMC
• Network: Gbps Ethernet
• WiFi: 802.11b/g/n
• Bluetooth: 4.0 dual mode
• USB Host: 2 x Independent USB Host
• MicroSD Slot: 1 x Slot. It supports system booting or is used to hold a storage card
• Audio Input/Output: 5-Pin, 2.0mm pitch pin-header
• MicroUSB: power input
• Debug Serial: 4Pin, 2.54mm pitch pin-header
• GPIO1:24Pin, 2.54mm pitch double-row pin-header containing UART, SPI, I2C and IO
• GPIO2:12Pin, 2.54mm pitch pin-header containing USB, IR receiver,I2S and IO
• Power Supply: DC 5V/2A
• PCB Dimension: 40 x 52mm
• PCB Layer: 6-Layer

3 Software Features

3.1 UbuntuCore

• mainline kernel: Linux-4.x.y
• UbuntuCore 16.04
• 64-bit OS
• supports FriendlyElec’s BakeBit Kit
• supports FriendlyElec’s NanoHAT OLED
• pre-installed FriendlyElec’s NanoHAT Motor Python Library
• pre-installed WiringPi for GPIO access
• pre-installed RPi.GPIO for GPIO access
• npi-config: system configuration utility for setting passwords, language, timezone, hostname, SSH and auto-login.
• networkmanager: a network utility to manage networking
• auto-login with user account "pi" with access to npi-config
• supports Gbps Ethernet
• supports WiFi and Bluetooth
• supports FriendlyElec's FA-CAM202 USB camera
• supports audio recording and playing

3.2 Debian for NAS Dock

• supports FriendlyElec’s NAS Dock
• pre-installed OpenMediaVault

4 Diagram, Layout and Dimension

4.1 Layout

NanoPi NEO Plus2 Layout

pinout

• GPIO Pin Description

Pin#	Name	Linux gpio	Pin#	Name	Linux gpio
1	SYS_3.3V		2	VDD_5V
3	I2C0_SDA / GPIOA12	12	4	VDD_5V
5	I2C0_SCL / GPIOA11	11	6	GND
7	GPIOG11	203	8	UART1_TX / GPIOG6	198
9	GND		10	UART1_RX / GPIOG7	199
11	UART2_TX / GPIOA0	0	12	GPIOA6	6
13	UART2_RTS / GPIOA2	2	14	GND
15	UART2_CTS / GPIOA3	3	16	UART1_RTS / GPIOG8	200
17	SYS_3.3V		18	UART1_CTS / GPIOG9	201
19	SPI0_MOSI / GPIOC0	64	20	GND
21	SPI0_MISO / GPIOC1	65	22	UART2_RX / GPIOA1	1
23	SPI0_CLK / GPIOC2	66	24	SPI0_CS / GPIOC3	67

• USB/Audio/IR Pin Description

NanoPi NEO Plus2
Pin#	Name	Description
1	VDD_5V	5V Power Out
2	USB-DP1	USB1 DP Signal
3	USB-DM1	USB1 DM Signal
4	USB-DP2	USB2 DP Signal
5	USB-DM2	USB2 DM Signal
6	GPIOL11 / IR-RX	GPIOL11 or IR Receive
7	SPDIF-OUT / GPIOA17	GPIOA17 or SPDIF-OUT
8	PCM0_SYNC / I2S0_LRC	I2S / PCM Sample Rate Clock/Sync
9	PCM0_CLK / I2S0_BCK	I2S / PCM Sample Rate Clock
10	PCM0_DOUT / I2S0_SDOUT	I2S / PCM Serial Data Output
11	PCM0_DIN / I2S0_SDIN	I2S / PCM Serial Data Input
12	GND	0V

• Audio

Pin#	Name	Description
1	MICIN1P	Microphone Positive Input
2	MICIN1N	Microphone Negative Input
3	LINEOUTR	LINE-OUT Right Channel Output
4	GND	0V
5	LINEOUTL	LINE-OUT Left Channel Output

• Debug Port（UART0）

DBG_UART

Pin#	Name
1	GND
2	VDD_5V
3	UART_TXD0 / GPIOA4
4	UART_RXD0 / GPIOA5 / PWM0

Note:

1. SYS_3.3V: 3.3V power output
2. VVDD_5V: 5V power input/output. The input range is 4.7V ~ 5.6V
3. All pins are 3.3V, output current is 5mA
4. For more details refer to the document: NanoPi-NEO-Plus2-1704-Schematic.pdf

4.2 Dimensional Diagram

For more details refer to: [Dimensions_NanoPi-NEO-Plus2-1704]

5 Get Started

5.1 Essentials You Need

Before starting to use your NanoPi NEO Plus2 get the following items ready:

• NanoPi NEO Plus2
• microSD Card/TFCard: Class 10 or Above, minimum 8GB SDHC
• microUSB power. A 5V/2A power is a must
• A Host computer running Ubuntu 16.04 64 bit system

5.2 TF Cards We Tested

To make your NanoPi NEO Plus2 boot and run fast we highly recommend you use a Class10 8GB SDHC TF card or a better one. The following cards are what we used in all our test cases presented here:

• SanDisk TF 8G Class10 Micro/SD TF card:

• SanDisk TF128G MicroSDXC TF 128G Class10 48MB/S:

• 川宇 8G C10 High Speed class10 micro SD card:

5.3 Make an Installation TF Card

5.3.1 Get Image Files

Visit this link download link to download image files(under the "official-ROMs" directory) and the flashing utility(under the "tools" directory):

Image Files:
nanopi-neo-plus2_friendlycore-xenial_4.x.y_YYYYMMDD.img.zip	FriendlyCore (base on UbuntuCore) Image File, kernel:Linux-4.x
nanopi-neo-plus2_debian-nas-jessie_4.x.y_YYYYMMDD.img.zip	NAS image file, kernel:Linux-4.x, for 1-bay NAS Dock
nanopi-neo-plus2_ubuntu-oled_4.x.y_YYYYMMDD.img.zip	OLED image file, kernel:Linux-4.x, for NanoHat OLED
nanopi-neo-plus2_eflasher_4.x.y_YYYYMMDD.img.zip	eflasher image file, kernel:Linux-4.x
Flash Utility:
win32diskimager.rar	Windows utility for flashing Debian image. Under Linux users can use "dd"

5.3.2 Make Installation MicroSD Card

• Extract the nanopi-neo-plus2_friendlycore-xenial_4.x.y_YYYYMMDD.img.zip and win32diskimager.rar. Insert a MicroSD card(at least 8G) into a Windows PC and run the win32diskimager utility as administrator. On the utility's main window select your card's drive, the wanted image file and click on "write" to start flashing the card till it is done.
• Insert this card into your NEO Plus2's MicroSD card slot and power on (with a 5V/2A power source). If the blue LED blinks this indicates your NEO Plus2 has successfully booted.
  

5.3.3 Flash Image to eMMC

• Extract the nanopi-neo-plus2_eflasher_4.x.y_YYYYMMDD.img.zip package and win32diskimager.rar. Insert a MicroSD card(at least 8G) into a Windows PC and run the win32diskimager utility as administrator. On the utility's main window select your SD card's drive, the wanted image file and click on "write" to start flashing the MicroSD card.
• Insert this card into your NEO Plus2 and power on (with a 5V/2A power source) the board. If the green LED is on and blue LED is blinks it indicates your eflasher has started successfully.
  
• Run the following command on a terminal:

$ eflasher

Select your wanted OS and type "yes" to start flashing. After it is done take off the card, reboot your board it will boot from eMMC.

6 Work with FriendlyCore

6.1 Introduction

FriendlyCore is a light Linux system without X-windows, based on ubuntu core, It uses the Qt-Embedded's GUI and is popular in industrial and enterprise applications.

Besides the regular Ubuntu core's features our FriendlyCore has the following additional features:

• it supports our LCDs with both capacitive touch and resistive touch(S700, X710, HD702, S430, HD101 and S70)
• it supports WiFi
• it supports Ethernet
• it supports Bluetooth and has been installed with bluez utilities
• it supports audio playing
• it supports Qt 5.10.0 EGLES and OpenGL ES1.1/2.0 (Only for S5P4418/S5P6818)

6.2 System Login

• If your board is connected to an HDMI monitor you need to use a USB mouse and keyboard.
• If you want to do kernel development you need to use a serial communication board, ie a PSU-ONECOM board, which will

For example, NanoPi-M1：

You can use a USB to Serial conversion board too.
Make sure you use a 5V/2A power to power your board from its MicroUSB port:
For example, NanoPi-NEO2：

• FriendlyCore User Accounts:

Non-root User:

   User Name: pi
   Password: pi

Root:

   User Name: root
   Password: fa

The system is automatically logged in as "pi". You can do "sudo npi-config" to disable auto login.

• Update packages

$ sudo apt-get update

6.3 Configure System with npi-config

The npi-config is a commandline utility which can be used to initialize system configurations such as user password, system language, time zone, Hostname, SSH switch , Auto login and etc. Type the following command to run this utility.

$ sudo npi-config

Here is how npi-config's GUI looks like:

6.4 Develop Qt Application

Please refer to: How to Build and Install Qt Application for FriendlyELEC Boards

6.5 Setup Program to AutoRun

You can setup a program to autorun on system boot with npi-config:

sudo npi-config

Go to Boot Options -> Autologin -> Qt/Embedded, select Enable and reboot.

6.6 Extend TF Card's Section

When FriendlyCore is loaded the TF card's section will be automatically extended.You can check the section's size by running the following command:

$ df -h

6.7 Transfer files using Bluetooth

Take the example of transferring files to the mobile phone. First, set your mobile phone Bluetooth to detectable status, then execute the following command to start Bluetooth search.：

hcitool scan

Search results look like：

Scanning ...
    2C:8A:72:1D:46:02   HTC6525LVW

This means that a mobile phone named HTC6525LVW is searched. We write down the MAC address in front of the phone name, and then use the sdptool command to view the Bluetooth service supported by the phone：

sdptool browser 2C:8A:72:1D:46:02

Note: Please replace the MAC address in the above command with the actual Bluetooth MAC address of the mobile phone.
This command will detail the protocols supported by Bluetooth for mobile phones. What we need to care about is a file transfer service called OBEX Object Push. Take the HTC6525LVW mobile phone as an example. The results are as follows：

Service Name: OBEX Object Push
Service RecHandle: 0x1000b
Service Class ID List:
  "OBEX Object Push" (0x1105)
Protocol Descriptor List:
  "L2CAP" (0x0100)
  "RFCOMM" (0x0003)
    Channel: 12
  "OBEX" (0x0008)
Profile Descriptor List:
  "OBEX Object Push" (0x1105)
    Version: 0x0100

As can be seen from the above information, the channel used by the OBEX Object Push service of this mobile phone is 12, we need to pass it to the obexftp command, and finally the command to initiate the file transfer request is as follows：

obexftp --nopath --noconn --uuid none --bluetooth -b 2C:8A:72:1D:46:02 -B 12 -put example.jpg

Note: Please replace the MAC address, channel and file name in the above command with the actual one.

After executing the above commands, please pay attention to the screen of the mobile phone. The mobile phone will pop up a prompt for pairing and receiving files. After confirming, the file transfer will start.

Bluetooth FAQ：
1) Bluetooth device not found on the development board, try to open Bluetooth with the following command：

rfkill unblock 0

2) Prompt can not find the relevant command, you can try to install related software with the following command：

apt-get install bluetooth bluez obexftp openobex-apps python-gobject ussp-push

6.8 WiFi

For either an SD WiFi or a USB WiFi you can connect it to your board in the same way. The APXX series WiFi chips are SD WiFi chips. By default FriendlyElec's system supports most popular USB WiFi modules. Here is a list of the USB WiFi modules we tested:

Index	Model
1	RTL8188CUS/8188EU 802.11n WLAN Adapter
2	RT2070 Wireless Adapter
3	RT2870/RT3070 Wireless Adapter
4	RTL8192CU Wireless Adapter
5	mi WiFi mt7601
6	5G USB WiFi RTL8821CU
7	5G USB WiFi RTL8812AU

You can use the NetworkManager utility to manage network. You can run "nmcli" in the commandline utility to start it. Here are the commands to start a WiFi connection:

• Change to root

$ su root

• Check device list

$ nmcli dev

Note: if the status of a device is "unmanaged" it means that device cannot be accessed by NetworkManager. To make it accessed you need to clear the settings under "/etc/network/interfaces" and reboot your system.

• Start WiFi

$ nmcli r wifi on

• Scan Surrounding WiFi Sources

$ nmcli dev wifi

• Connect to a WiFi Source

$ nmcli dev wifi connect "SSID" password "PASSWORD" ifname wlan0

The "SSID" and "PASSWORD" need to be replaced with your actual SSID and password.If you have multiple WiFi devices you need to specify the one you want to connect to a WiFi source with iface
If a connection succeeds it will be automatically setup on next system reboot.

For more details about NetworkManager refer to this link: Use NetworkManager to configure network settings

If your USB WiFi module doesn't work most likely your system doesn't have its driver. For a Debian system you can get a driver from Debian-WiFi and install it on your system. For a Ubuntu system you can install a driver by running the following commands:

$ apt-get install linux-firmware

In general all WiFi drivers are located at the "/lib/firmware" directory.

6.9 Ethernet Connection

If a board is connected to a network via Ethernet before it is powered on it will automatically obtain an IP with DHCP activated after it is powered up. If you want to set up a static IP refer to: Use NetworkManager to configure network settings。

6.10 Custom welcome message

The welcome message is printed from the script in this directory：

/etc/update-motd.d/

For example, to change the FriendlyELEC LOGO, you can change the file /etc/update-motd.d/10-header. For example, to change the LOGO to HELLO, you can change the following line：

TERM=linux toilet -f standard -F metal $BOARD_VENDOR

To:

TERM=linux toilet -f standard -F metal HELLO

6.11 Modify timezone

For exampe, change to Shanghai timezone:

sudo rm /etc/localtime
sudo ln -ls /usr/share/zoneinfo/Asia/Shanghai /etc/localtime

6.12 Set Audio Device

If your system has multiple audio devices such as HDMI-Audio, 3.5mm audio jack and I2S-Codec you can set system's default audio device by running the following commands.

• After your board is booted run the following commands to install alsa packages:

$ apt-get update
$ apt-get install libasound2
$ apt-get install alsa-base
$ apt-get install alsa-utils

• After installation is done you can list all the audio devices by running the following command. Here is a similar list you may see after you run the command:

$ aplay -l
card 0: HDMI
card 1: 3.5mm codec
card 2: I2S codec

"card 0" is HDMI-Audio, "card 1" is 3.5mm audio jack and "card 2" is I2S-Codec. You can set default audio device to HDMI-Audio by changing the "/etc/asound.conf" file as follows:

pcm.!default {
    type hw
    card 0
    device 0
}
 
ctl.!default {
    type hw
    card 0
}

If you change "card 0" to "card 1" the 3.5mm audio jack will be set to the default device.
Copy a .wav file to your board and test it by running the following command:

$ aplay /root/Music/test.wav

You will hear sounds from system's default audio device.
If you are using H3/H5/H2+ series board with mainline kernel, the easier way is using npi-config。

6.13 Connect to USB Camera(FA-CAM202)

The FA-CAM202 is a 200M USB camera. You can refer to <Connect DVP Camera (CAM500B) to Board> on how to connect a USB camera to a board.
You need to change the start.sh script and make sure it uses a correct /dev/videoX node. You can check your FA-CAM202's node by running the following commands:

$ apt-get install v4l-utils
$ v4l2-ctl -d /dev/video1 -D
Driver Info (not using libv4l2):
        Driver name   : uvcvideo
        Card type     : HC 3358+2100: HC 3358+2100
        Bus info      : usb-1c1b000.usb-1
	...

Information above indicates that /dev/video1 is the device node of the FA-CAM 202.

6.14 Check CPU's Working Temperature

You can get CPU's working temperature by running the following command:

$ cpu_freq
CPU0 online=1 temp=26581 governor=ondemand cur_freq=480000
CPU1 online=1 temp=26581 governor=ondemand cur_freq=480000
CPU2 online=1 temp=26581 governor=ondemand cur_freq=480000
CPU3 online=1 temp=26581 governor=ondemand cur_freq=480000

This message means there are currently four CPUs working. All of their working temperature is 26.5 degree in Celsius and each one's clock is 480MHz.

6.15 Test Watchdog

You can test watchdog by running the following commands:

$ cd /root/demo/watchdog/
$ gcc watchdog_demo.c -o watchdog_demo
$ ./watchdog_demo /dev/watchdog0 10
Set timeout: 10 seconds
Get timeout: 10 seconds
System will reboot in 10 second

System will reboot in 10 seconds.

6.16 Test Infrared Receiver

Note: Please Check your board if IR receiver exist.
By default the infrared function is disabled you can enable it by using the npi-config utility:

$ npi-config
    6 Advanced Options     Configure advanced settings
        A8 IR              Enable/Disable IR
            ir Enable/Disable ir[enabled]

Reboot your system and test its infrared function by running the following commands:

$ apt-get install ir-keytable
$ echo "+rc-5 +nec +rc-6 +jvc +sony +rc-5-sz +sanyo +sharp +mce_kbd +xmp" > /sys/class/rc/rc0/protocols   # Enable infrared
$ ir-keytable -t
Testing events. Please, press CTRL-C to abort.

"ir-keytable -t" is used to check whether the receiver receives infrared signals. You can use a remote control to send infrared signals to the receiver. If it works you will see similar messages as follows:

1522404275.767215: event type EV_MSC(0x04): scancode = 0xe0e43
1522404275.767215: event type EV_SYN(0x00).
1522404278.911267: event type EV_MSC(0x04): scancode = 0xe0e42
1522404278.911267: event type EV_SYN(0x00).

6.17 Read CHIP ID

As for Allwinner H2+/H3/H5/ SoCs each of these CPUs has an internal 16-btye CHIP ID which can be read by running the following commands in the Linux-4.14 kernel:

$ apt-get install bsdmainutils
$ hexdump /sys/bus/nvmem/devices/sunxi-sid0/nvmem 
0000000 8082 0447 0064 04c3 3650 ce0a 1e28 2202
0000010 0002 0000 0000 0000 0000 0000 0000 0000
0000020 0000 0000 0000 0000 0000 0000 0000 0000
0000030 0000 0008 0508 0000 0000 0000 0000 0000
0000040 0000 0000 0000 0000 0000 0000 0000 0000

"8082 0447 0064 04c3 3650 ce0a 1e28 2202" is the 16-byte CHIP ID.

6.18 Access GPIO Pins/Wirings with WiringNP

The wiringPi library was initially developed by Gordon Henderson in C. It contains libraries to access GPIO, I2C, SPI, UART, PWM and etc. The wiringPi library contains various libraries, header files and a commandline utility:gpio. The gpio utility can be used to read and write GPIO pins.
FriendlyElec integrated this utility in FriendlyCore system allowing users to easily access GPIO pins. For more details refer to WiringNP WiringNP

6.19 Run Qt Demo

Run the following command

$ sudo /opt/QtE-Demo/run.sh

Here is what you expect to observe. This is an open source Qt Demo:

6.20 How to install and use docker (for arm64 system)

6.20.1 How to Install Docker

Run the following commands：

sudo apt-get update
sudo apt-get install docker.io

6.20.2 Test Docker installation

Test that your installation works by running the simple docker image:

git clone https://github.com/friendlyarm/debian-jessie-arm-docker
cd debian-jessie-arm-docker
./rebuild-image.sh
./run.sh

6.21 Record and Play Audio File

The NanoPi NEO Plus2 has an audio interface: 2.0mm pitch 5-pin pin-header:

Pin#	Name	Description
1	MICIN1P	Microphone Positive Input
2	MICIN1N	Microphone Negative Input
3	LINEOUTR	LINE-OUT Right Channel Output
4	GND	地
5	LINEOUTL	LINE-OUT Left Channel Output

Here is a hardware setup for connecting an audio device to a NanoPi NEO Plus2:
耳麦标注
Make sure an audio device is connected to your NEO Plus2 and then you can test audio recording and playing by running the following commands.
Check audio devices:

$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: audiocodec [audiocodec], device 0: SUNXI-CODEC sun50iw2codec-0 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0

Play Audio Files:

$ aplay /root/Music/test.wav -D plughw:0

Record Audio:

$ arecord -f cd -d 5 test.wav

7 Make Your Own FriendlyCore

7.1 Use Mainline BSP

The NanoPi NEO Plus2 has gotten support for a 64-bit kernel: Linux-4.x.y with Ubuntu Core 16.04. For more details about how to use mainline u-boot and Linux-4.x.y refer to :Mainline U-boot & Linux

8 Resources

8.1 Schematics and Datasheets

• Schematic: NanoPi-NEO-Plus2-1704-Schematic.pdf
• Dimensions: NanoPi-NEO-Plus2-1704_pcb file in dxf format
• H5 Datasheet: Allwinner_H5_Datasheet_V1.0.pdf

9 Update Log

9.1 May-30-2017

• Released English Version