Difference between revisions of "NanoPi NEO"

Revision as of 09:10, 7 July 2016

查看中文

1 Introduction

Overview

Front

Back

• The NanoPi NEO(abbreviated as NEO) is another fun board developed by FriendlyARM for makers, hobbyists and fans.

2 Features

• CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
• DDR3 RAM: 256MB/512MB
• Connectivity: 10/100M Ethernet
• USB Host: Type-A x 1, 2.54 mm pin x 2
• MicroSD Slot x 1
• MicroUSB: for data transmission and power input
• Debug Serial Port: 4Pin, 2.54 mm pitch pin header
• GPIO: 2.54mm pitch 36pin. It includes UART, SPI, I2C, IO etc
• PCB Dimension: 40 x 40 mm
• Power Supply: DC 5V/2A
• OS/Software: u-boot and UbuntuCore

3 Diagram, Layout and Dimension

3.1 Layout

NanoPi NEO Layout

• GPIO Pin Description

Pin#	Name	Linux gpio	Pin#	Name	Linux gpio
1	SYS_3.3V		2	VDD_5V
3	I2C0_SDA		4	VDD_5V
5	I2C0_SCL		6	GND
7	GPIOG11	203	8	UART1_TX/GPIOG6	198
9	GND		10	UART1_RX/GPIOG7	199
11	UART2_TX/GPIOA0	0	12	PWM1/GPIOA6	6
13	UART2_RTS/GPIOA2	2	14	GND
15	UART2_CTS/GPIOA3	3	16	UART1_RTS/GPIOG8	200
17	SYS_3.3V		18	UART1_CTS/GPIOG9	201
19	SPI0_MOSI/GPIOC0	64	20	GND
21	SIP0_MISO/GPIOC1	65	22	UART2_RX/GPIOA1	1
23	SPI0_CLK/GPIOC29	93	24	SPI0_CS/GPIOC3	67

• USB/Audio/IR Pin Description

Pin#	Name	Description
1	VDD_5V	5V Power Out
2	USB-DP1	USB1 DP Signal
3	USB-DM1	USB1 DM Signal
4	USB-DP2	USB2 DP Signal
5	USB-DM2	USB2 DM Signal
6	GPIOL11/IR-RX	GPIOL11 or IR Receive
7	SPDIF-OUT/GPIOA17	GPIOA17 or SPDIF-OUT
8	MICIN1P	Microphone Positive Input
9	MICIN1N	Microphone Negative Input
10	LINEOUTR	LINE-OUT Right Channel Output
11	LINEOUTL	LINE-OUT Left Channel Output
12	GND	0V

• Debug Port（UART0）

Pin#	Name
1	GND
2	VDD_5V
3	UART_TXD0
4	UART_RXD0

Note:

1. SYS_3.3V: 3.3V power output
2. VVDD_5V: 5V power input/output. When the external device’s power is greater than the MicroUSB's the external device is charging the board otherwise the board powers the external device. The input range is 4.7V ~ 5.6V
3. All pins are 3.3V, output current is 5mA
4. For more details refer to the document: NanoPi-NEO-1606-Schematic.pdf

3.2 Dimensional Diagram

For more details refer to the document: pcb file in dxf format

4 Get Started

4.1 Essentials You Need

Before starting to use your NanoPi NEO get the following items ready

• NanoPi NEO
• microSD Card/TFCard: Class 10 or Above, minimum 8GB SDHC
• microUSB power. A 5V/2A power is a must
• A Host computer running Ubuntu 14.04 64 bit system

4.2 TF Cards We Tested

To make your NanoPi NEO boot and run fast we highly recommand you use a Class10 8GB SDHC TF card or a better one. The following cards are what we used in all our test cases presented here:

• SanDisk TF 8G Class10 Micro/SD TF card:

• SanDisk TF128G MicroSDXC TF 128G Class10 48MB/S:

• 川宇 8G C10 High Speed class10 micro SD card:

4.3 Make an Installation TF Card

4.3.1 Get Image Files

Visit this link download link to download image files and the flashing utility:

Image Files
nanopi-neo-core-qte-sd4g.img.zip	UbuntuCore with Qt-Embedded Image File
Flash Utility:
win32diskimager.rar	Windows utility for flashing Debian image. Under Linux users can use "dd"

4.3.2 Make UbuntuCore with Qt Embedded Image Card

• Uncompress the nanopi-neo-core-qte-sd4g.img.zip and win32diskimager.rar files. Insert a TF card(at least 4G) into a Windows PC and run the win32diskimager utility as administrator. On the utility's main window select your TF card's drive, the wanted image file and click on "write" to start flashing the TF card.

5 Work with Ubuntu-Core with Qt-Embedded

5.1 Run Ubuntu-Core with Qt-Embedded

• Insert a TF card with UbuntuCore image files into your NanoPi NEO, connect the board to a 5V/2A power source the board will be automatically powered on. If you can see the blue LED flashing it means your board is working and UbuntuCore is being loaded.
  
• If you want to do kernel development you need to use a serial communication board, ie a PSU-ONECOM board, which will allow you to operate the board via a serial terminal.
  
• Here is a setup where we connect a NanoPi M1 to a PC via the PSU-ONECOM and you can power on your M1 from either the PSU-ONECOM or the board's MicroUSB:

• The password for "root" is "fa".
• Update packages

sudo apt-get update

5.2 Ethernet Connection

If the NanoPi NEO is connected to a network via Ethernet before it is powered on it will automatically obtain an IP after it is powered up. If it is not connected via Ethernet or its DHCP is not activated obtaining an IP will fail and system will hang on for about 15 to 60 seconds.

5.3 SSH登录NEO

NEO没有任何图形界面输出的接口，如果你没有串口模块，可以通过SSH协议登录NEO。假设通过路由器查看到NEO的IP地址为192.168.1.230，你可以在PC机上执行如下命令登录NEO:

ssh root@192.168.1.230

密码为fa。

5.4 扩展TF卡文件系统

强烈建议做好系统运行卡之后立即进行文件系统 rootfs 分区的扩展，这将大大提升系统的性能，避免空间不足带来的各种繁琐问题。

• 方法1: 在PC机上扩展TF卡的文件系统 rootfs 分区：

sudo umount /dev/sdx?
sudo parted /dev/sdx unit % resizepart 2 100 unit MB print
sudo resize2fs -f /dev/sdx2

/dev/sdx请替换为实际的TF卡设备文件名。

• 方法2: 在NEO上扩展TF卡的文件系统 rootfs 分区，在NEO上运行Ubuntu-Core，然后执行命令：

sudo fs_resize

根据提示，输入 y 开始扩展文件系统，然后再输入 y 选择重启NEO。重启后执行下列命令查看新分区大小：

df -h

5.5 连接USB WiFi

系统默认已经支持市面上众多常见的USB WiFi，想知道你的USB WiFi是否可用只需将其接在NEO上即可，已测试过的USB WiFi型号如下：

序号	型号
1	RTL8188CUS/8188EU 802.11n WLAN Adapter
2	RT2070 Wireless Adapter
3	RT2870/RT3070 Wireless Adapter
4	RTL8192CU Wireless Adapter
5	小米WiFi mt7601

5.6 查看CPU工作温度

获取当前CPU的温度、运行频率等信息：

cpu_freq

6 如何编译Ubuntu-Core with Qt-Embedded系统

访问此处下载地址的sources目录，下载源码nanopi-H3-bsp。
使用7-Zip工具解压后得到两个目录：lichee和android，也可以从github上克隆lichee源码：

git clone https://github.com/friendlyarm/h3_lichee.git lichee

注：lichee是全志为其CPU的板级支持包所起的项目名称，里面包含了U-boot，Linux等源码和众多的编译脚本。

6.1 编译lichee源码

编译全志 H3 的BSP源码包必须使用64bit的Linux PC系统，并安装下列软件包，下列操作均基于Ubuntu-14.04 LTS-64bit：

sudo apt-get install gawk git gnupg flex bison gperf build-essential \
zip curl libc6-dev libncurses5-dev:i386 x11proto-core-dev \
libx11-dev:i386 libreadline6-dev:i386 libgl1-mesa-glx:i386 \
libgl1-mesa-dev g++-multilib mingw32 tofrodos \
python-markdown libxml2-utils xsltproc zlib1g-dev:i386

编译lichee源码包，进入lichee目录，执行命令：

cd lichee
./build.sh -p sun8iw7p1 -b nanopi-h3

该命令会一次性编译好U-boot、Linux内核和模块。
注：lichee目录里内置了交叉编译器，当使用build.sh脚本进行源码编译时，会自动使用该内置的编译器，所以无需手动安装编译器。

6.2 打包系统组件

./gen_script.sh nanopi-neo

该命令会将所有编译生成的可执行文件(包括U-boot、Linux内核)和系统配置文件拷贝到lichee/tools/pack/out/目录以便进行统一管理，并且会该目录下生成 script.bin文件。
script.bin是全志系列 CPU 的硬件板级配置文件，相关信息请查看script.bin。

下列命令可用于更新TF卡上的U-boot：

./fuse_uboot.sh /dev/sdx

/dev/sdx请替换为实际的TF卡设备文件名。
uImage和内核模块均位于linux-3.4/output目录下，将uImage拷贝到TF卡的boot分区的根目录即可更新内核。

6.3 编译U-boot

如果你想单独编译U-boot，可以执行命令：

./build.sh -p sun8iw7p1 -b nanopi-h3 -m uboot

编译生成的可执行文件需打上全志系列CPU的硬件板级配置补丁后才能烧写到TF卡上运行，执行./build.sh pack能自动完成打补丁的操作。
如何手动为U-boot打补丁请查看H3_Manual_build_howto，执行下列命令更新TF卡上的U-boot：

./fuse_uboot.sh /dev/sdx

/dev/sdx请替换为实际的TF卡设备文件名。

6.4 编译Linux内核

如果你想单独编译Linux内核，可以执行命令：

./build.sh -p sun8iw7p1 -b nanopi-h3 -m kernel

编译完成后uImage和内核模块均位于linux-3.4/output目录下，将uImage拷贝到TF卡的boot分区的根目录即可。

6.5 清理lichee源码

./build.sh -p sun8iw7p1_linux -b nanopi-h3 -m clean

7 Resources

• Schematics
  • NanoPi-NEO-1606-Schematic.pdf
• Dimensional Diagram
  • pcb file in dxf format
• H3 Datesheet Allwinner_H3_Datasheet_V1.2.pdf