Difference between revisions of "NanoPi M1"

From FriendlyELEC WiKi
Jump to: navigation, search
(Layout)
(Layout)
Line 118: Line 118:
 
|11  || VSYNC || vertical synchronization to CPU from camera modules
 
|11  || VSYNC || vertical synchronization to CPU from camera modules
 
|-  
 
|-  
|12  || HREF/HSYNC || horizontal synchronization to CPU from camera modules
+
|12  || HREF/HSYNC || HREF/HSYNC signal to CPU from camera modules
 
|-
 
|-
|14  || PCLK      || 外部摄像头模块输出给CPU的像数点信号
+
|14  || PCLK      || PCLK signal to CPU from camera modules
 
|-
 
|-
|16-23 || Data bit7-0 || 数据信号
+
|16-23 || Data bit7-0 || data signals
 
|}
 
|}
:'''说明'''
+
:'''Note:'''
::#SYS_3.3V: 3.3V电源输出
+
::#SYS_3.3V: 3.3V power output
::#VDD_5V: 5V电源输入/输出。当电压大于MicroUSB时,向板子供电,否则板子从MicroUSB取电。输入范围:4.7~5.6V
+
::#VDD_5V: 5V power input/output. When the external device’s power is greater than the MicroUSB’s the external device is charging the board otherwise the board powers the external device. The input range is 4.7V ~ 5.6V
::#全部信号引脚均为3.3V电平,输出电流为5mA,可以带动小负荷模块,io都不能带负载
+
::#All pins are 3.3V and output current is 5mA. It can drive small loads.可以带动小负荷模块,io都不能带负载
::#更详细的信息请查看原理图:[http://wiki.friendlyarm.com/wiki/images/d/d8/NanoPi-M1-1603-Schematic.pdf NanoPi-M1-1603-Schematic.pdf]
+
::#For more details please refer to the document: [http://wiki.friendlyarm.com/wiki/images/d/d8/NanoPi-M1-1603-Schematic.pdf NanoPi-M1-1603-Schematic.pdf]
  
 
===Board Dimension===
 
===Board Dimension===

Revision as of 10:54, 14 March 2016

查看中文

1 介绍

Overview
Front
Back
frameless
  • NanoPi M1(以下简称M1)是友善之臂团队面向创客、嵌入式爱好者,电子艺术家、发烧友等群体推出的又一款完全开源的掌上创客神器,它的大小只有树莓派的大约2/3,可运行Ubuntu MATE、Debian、Android等操作系统。
  • NanoPi M1采用了全志高性能处理器Allwinner H3,集成以太网、红外接收、视频/音频输出等接口,支持HDMI、AVOUT视频输出等功能。
  • 尽管体积很小,设计却紧凑美观。NanoPi M1引出了相当丰富的接口,包括HDMI、以太网、USB-Host、USB-OTG、DVP camera和AVOUT(音频+视频)等。而且集成了板载麦克风,红外接收器,并且兼容树莓派GPIO口,并且拥有独立的调试串口等。

2 Features

  • CPU: Allwinner H3, Quad-core Cortex-A7@1.2GHz
  • GPU: Mali400MP2@600MHz,Supports OpenGL ES2.0
  • DDR3 RAM: 512MB
  • Connectivity: 10/100M Ethernet
  • Audio: 3.5mm audio jack/Via HDMI
  • Microphone: Onboard microphone
  • IR Receiver: Onboard IR receiver
  • USB Host:Type A, USB 2.0 x 3
  • MicroSD Slot x 1
  • MicroUSB: for data transmission and power input, OTG
  • Video Output: HDMI 1.4 1080P, CVBS
  • DVP Camera Interface: 24pin, 0.5mm pitch FPC seat
  • Debug Serial Port: 4Pin, 2.54mm pitch pin header
  • GPIO: 2.54mm spacing 40pin, compatible with Raspberry Pi's GPIO. It includes UART, SPI, I2C, IO etc
  • User Key: Power LED x 1, Reset x 1
  • PC Size: 64 x 50mm
  • Power Supply: DC 5V/2A
  • OS/Software: u-boot,Ubuntu MATE,Debian

compact

3 Diagram, Layout and Dimension

3.1 Layout

NanoPi M1 Layout
  • GPIO Pin Spec
Pin# Name Pin# Name
1 SYS_3.3V 2 VDD_5V
3 I2C0_SDA 4 VDD_5V
5 I2C0_SCL 6 GND
7 GPIOG11 8 UART1_TX/GPIOG6
9 GND 10 UART1_RX/GPIOG7
11 UART2_TX/GPIOA0 12 PWM1/GPIOA6
13 UART2_RTS/GPIOA2 14 GND
15 UART2_CTS/GPIOA3 16 UART1_RTS/GPIOG8
17 SYS_3.3V 18 UART1_CTS/GPIOG9
19 SPI0_MOSI/GPIOC0 20 GND
21 SIP0_MISO/GPIOC1 22 UART2_RX/GPIOA1
23 SPI0_CLK/GPIOC29 24 SPI0_CS/GPIOC3
25 GND 26 SPDIF-OUT/GPIOA17
27 I2C1_SDA/GPIOA19 28 I2C1_SCL/GPIOA18
29 GPIOA20 30 GND
31 GGPIOA21 32 GPIOA7
33 GPIOA8 34 GND
35 UART3_CTS/SPI1_MISO/GPIOA16 36 UART3_TX/SPI1_CS/GPIOA13
37 GPIOA9 38 UART3_RTS/SPI1_MOSI/GPIOA15
39 GND 40 UART3_RX/SPI1_CLK/GPIOA14
  • Debug Port(UART0)
Pin# Name
1 GND
2 VDD_5V
3 UART_TXD0
4 UART_RXD0
  • DVP Camera IF Pin Spec
Pin# Name Description
1, 2 SYS_3.3V 3.3V power output, to camera modules
7,9,13,15,24 GND Gound, 0V
3 I2C2_SCL I2C Clock Signal
4 I2C2_SDA I2C Data Signal
5 GPIOE15 Regular GPIO, control signals output to camera modules
6 GPIOE14 Regular GPIO, control signals output to camera modules
8 MCLK Clock signals output to camera modules
10 NC Not Connected
11 VSYNC vertical synchronization to CPU from camera modules
12 HREF/HSYNC HREF/HSYNC signal to CPU from camera modules
14 PCLK PCLK signal to CPU from camera modules
16-23 Data bit7-0 data signals
Note:
  1. SYS_3.3V: 3.3V power output
  2. VDD_5V: 5V power input/output. When the external device’s power is greater than the MicroUSB’s the external device is charging the board otherwise the board powers the external device. The input range is 4.7V ~ 5.6V
  3. All pins are 3.3V and output current is 5mA. It can drive small loads.可以带动小负荷模块,io都不能带负载
  4. For more details please refer to the document: NanoPi-M1-1603-Schematic.pdf

3.2 Board Dimension

NanoPi-M1-1603-dimensions.png

For more details please refer to: pcb file in dxf

4 快速入门

4.1 准备工作

5 Resources

Schematic NanoPi-M1-1603-Schematic.pdf
Dimensional Diagram pcb file in dxf