Difference between revisions of "NanoHat Proto"

From FriendlyELEC WiKi
Jump to: navigation, search
Line 5: Line 5:
 
*NanoHat Proto is a expansion board which has the same dimension as that of a NanoPi NEO/Air and can be stacked on a NanoPi NEO/Air.
 
*NanoHat Proto is a expansion board which has the same dimension as that of a NanoPi NEO/Air and can be stacked on a NanoPi NEO/Air.
 
*It is like a breadboard and has 14 columns of 100 mil (2.54mm pitch) land. Users can place various parts such as chips, resistors, LEDs and etc on the board.
 
*It is like a breadboard and has 14 columns of 100 mil (2.54mm pitch) land. Users can place various parts such as chips, resistors, LEDs and etc on the board.
<!---
+
*There are rows of 3.3V and GND pins and rows of 5V and GND pins.
*上下两侧分别是两排电源和地引脚,这两排引脚横向连接,最左侧标注了他们的功能。
+
*All pins except GND and PWR in the 24-Pin connector of the NanoPi NEO/Air are listed on the boards.
*The top row lists all the 26 pins of the pin-header of the NanoPi NEO/Air最顶上一排焊盘连接了NanoPi NEO/Air板26Pin接口除电源和地的所有引脚,并在焊盘下方标注了各自的功能。
+
--->
+
 
*It has an onboard 32K EEPROM chip AT24C32D whose address is 0x50. This EEPROM is available for data storage.
 
*It has an onboard 32K EEPROM chip AT24C32D whose address is 0x50. This EEPROM is available for data storage.
  
Line 17: Line 15:
  
 
* Pin Description:
 
* Pin Description:
<!---
+
All pins except GND and PWR in the 24-Pin connector of the NanoPi NEO/Air are listed on the boards. For more details on the NanoPi NEO/Air's 24-Pin connector refer to its wiki site.<br>
NanoPi NEO/Air接口在此不列举,请在NanoPi NEO/Air维基页面查阅。<br>
+
--->
+
 
([http://wiki.friendlyarm.com/wiki/index.php/NanoPi_NEO/zh NanoPi NEO])  ([http://wiki.friendlyarm.com/wiki/index.php/NanoPi_NEO_Air/zh NanoPi NEO Air])
 
([http://wiki.friendlyarm.com/wiki/index.php/NanoPi_NEO/zh NanoPi NEO])  ([http://wiki.friendlyarm.com/wiki/index.php/NanoPi_NEO_Air/zh NanoPi NEO Air])
 
<br>
 
<br>

Revision as of 09:09, 19 April 2017

查看中文

1 Introduction

NanoHat Proto
  • NanoHat Proto is a expansion board which has the same dimension as that of a NanoPi NEO/Air and can be stacked on a NanoPi NEO/Air.
  • It is like a breadboard and has 14 columns of 100 mil (2.54mm pitch) land. Users can place various parts such as chips, resistors, LEDs and etc on the board.
  • There are rows of 3.3V and GND pins and rows of 5V and GND pins.
  • All pins except GND and PWR in the 24-Pin connector of the NanoPi NEO/Air are listed on the boards.
  • It has an onboard 32K EEPROM chip AT24C32D whose address is 0x50. This EEPROM is available for data storage.

2 Hardware Spec

  • land's space:100mil(2.54mm)
  • Onboard 32K EEPROM

NanoHat Proto-PCB

  • Pin Description:

All pins except GND and PWR in the 24-Pin connector of the NanoPi NEO/Air are listed on the boards. For more details on the NanoPi NEO/Air's 24-Pin connector refer to its wiki site.
(NanoPi NEO) (NanoPi NEO Air)

顶上一排焊盘功能定义如下:

Pin Description
SDA0 I2C0_SDA
SCL0 I2C0_SCL
TXD1 UART1_TX
RXD1 UART1_RX
#11 Pin 11 of NanoPi NEO/Air's 24-pin connector
#22 Pin 22 of NanoPi NEO/Air's 24-pin connector
#12 Pin 12 of NanoPi NEO/Air's 24-pin connector
#13 Pin 13 of NanoPi NEO/Air's 24-pin connector
#15 Pin 15 of NanoPi NEO/Air's 24-pin connector
#16 Pin 16 of NanoPi NEO/Air's 24-pin connector
#18 Pin 18 of NanoPi NEO/Air's 24-pin connector
MOSI SPI0_MOSI
MISO SPI0_MISO
CLK SPI0_CLK
CS SPI0_CS

3 Hardware Setup

FriendlyElec makes two customized female connectors for the NanoHat Proto. After these two connectors are soldered on the board it can be stacked on a NanoPi NEO/Air. Here is a hardware setup:
Matrix - NanoHat Proto_nanopi_NEO

4 Resources