Difference between revisions of "Mini Shield for NanoPi Duo"

From FriendlyELEC WiKi
Jump to: navigation, search
(Audio)
(Hardware Spec)
Line 25: Line 25:
  
 
===Diagram, Layout and Dimension===
 
===Diagram, Layout and Dimension===
[[File:Mini Shield for NanoPi Duo-layout.jpg |thumb|600px|Mini Shield for NanoPi Duo Layout]]
+
[[File:Mini Shield for NanoPi Duo-layout.jpg |thumb|550px|Mini Shield for NanoPi Duo Layout]]
 
Here is a layout of ports and interfaces. There are detailed descriptions for ports and interfaces on the other side of the board.<br>
 
Here is a layout of ports and interfaces. There are detailed descriptions for ports and interfaces on the other side of the board.<br>
  
*  '''Mini Shield for NanoPi Duo Interface Pin Description '''
+
*  '''NanoPi Duo Pin-header Pin Description '''
 
::{| class="wikitable"
 
::{| class="wikitable"
 
|-
 
|-
Line 66: Line 66:
 
|}
 
|}
  
*  '''2x9 Pin Header Pin Description'''
+
*  '''9x2 Pin Header Pin Description'''
 
::{| class="wikitable"
 
::{| class="wikitable"
 
|-
 
|-

Revision as of 09:50, 9 November 2017

查看中文

1 Introduction

Mini Shield for NanoPi Duo 侧面
Mini Shield for NanoPi Duo 正面
Mini Shield for NanoPi Duo 底面
  • The Mini Shield for NanoPi Duo is a dedicated carrier board for the NanoPi Duo. It extends Duo's Ethernet, serial port, audio, USB and etc.
  • The mini shield has an onboard JMS567 USB to SATA IC and an mSATA interface.
  • The mini shield has an onboard FE1.1s which extends four USB Host ports.
  • It has a serial port and Ethernet port.
  • It has an onboard microphone and a 3.5mm audio jack.
  • The mini shield has a 2 x9 Pin header which extends NanoPi Duo's IO pins.
  • There is a 6-pin SPI header on the reverse side.
  • This shield's dimension and mounting holes' positions are exactly the same as those of a Raspberry Pi therefore it can well fit into a Raspberry Pi's case.

2 Hardware Spec

  • its dimension is the same as that of a Raspberry Pi and it can fit into a Pi's case
  • 4 x USB Host port
  • Serial port and Ethernet port
  • Audio input and output
  • 2 x 9 Pin GPIO header
  • 6 x Pin SPI header
  • PCB dimension(mm): 85 x 56

Mini Shield for NanoPi Duo_PCB

2.1 Diagram, Layout and Dimension

Mini Shield for NanoPi Duo Layout

Here is a layout of ports and interfaces. There are detailed descriptions for ports and interfaces on the other side of the board.

  • NanoPi Duo Pin-header Pin Description
Number# Name Number# Name
1 VDD_5V 1 DEBUG_RX(UART_RXD0)/GPIOA5/PWM0
2 VDD_5V 2 DEBUG_TX(UART_TXD0)/GPIOA4
3 SYS_3.3V 3 GND
4 GND 4 I2C0_SCL/GPIOA11
5 GPIOL11/IR-RX 5 I2C0_SDA/GPIOA12
6 GPIOG11 6 UART3_TX/SPI1_CS/GPIOA13
7 USB-DM3 7 UART3_RX/SPI1_CLK/GPIOA14
8 USB-DP3 8 UART3_CTS/SPI1_MISO/GPIOA16
9 USB-DM2 9 UART3_RTS/SPI1_MOSI/GPIOA15
10 USB-DP2 10 UART1_RX/GPIOG7
11 EPHY-RXN 11 UART1_TX/GPIOG6
12 EPHY-RXP 12 CVBS
13 EPHY-TXN 13 LINEOUT_L
14 EPHY-TXP 14 LINEOUT_R
15 EPHY-LED-LINK 15 MIC_P
16 EPHY-LED-SPD 16 MIC_N
  • 9x2 Pin Header Pin Description
Number# Name Number# Name
1 SYS_3.3V 2 VDD_5V
3 I2C0_SDA / GPIOA12 4 VDD_5V
5 I2C0_SCL / GPIOA11 6 GND
7 GPIOG11 8 UART1_TX / GPIOG6
9 GND 10 UART1_RX / GPIOG7
11 SPI1_MOSI/GPIOA15 12 GPIOL11
13 SPI1_MISO/GPIOA16 14 GND
15 SPI1_CLK/GPIOA14 16 SPI1_CS/GPIOA13
17 SYS_3.3V 18 NC
  • 6 Pin SPI Pin Header Pin Description
Number# Name
1 GND
2 SYS_3.3V
3 SPI1_CS/GPIOA13
4 SPI1_CLK/GPIOA14
5 SPI1_MOSI/GPIOA15
6 SPI1_MISO/GPIOA16

3 Hardware Setup

A NanoPi Duo can be mounted on a Mini Shield. Here is a hardware setup diagram:
Mini Shield for NanoPi Duo_NanoPi_Duo

It can fit into a Raspberry Pi's case. Here is a hardware setup:
Mini Shield for NanoPi Duo_NanoPi_Duo-2

4 Applications

4.1 Connect SSD to mSATA

Connect an SSD hard disk to the shield's mSATA, power on the board and type the following command to check the SSD's status:

fdisk -l

Here is what you expect to observe:
Check SSD

4.2 Boot System from SSD

A NanoPi-Duo can be booted from the SSD on a Mini Shield for NanoPi Duo. Booting OS from an SSD has the following benefits:
1) faster read/write;
2) much longer life time than a TF card;
3) more reliable than booting from a TF card;

You can install an OS to SSD by using the npi-config utility. Here are the steps to follow:

sudo npi-config

Enter the "Boot Options" menu, go to "Boot device" and you will see two options:
1) D1 Hard drive
2) D2 TF card
Select "D1 Hard drive" and proceed with its prompts.
Select "D2 TF card" to boot OS from a TF card.

If your npi-config doesn't have a "Boot device" menu it might be that your npi-config is out of date and you can update it by selecting "Update" in the menu.

4.3 Audio

1. Audio Recording:

arecord -D hw:00 -f cd test.wav

Here is what you expect to observe:
Record
2. Audio Playing:

aplay /root/Music/test.wav

Here is what you expect to observe:
Play

5 Resources

6 Update Log

6.1 August-16-2017

  • Released English Version