Matrix - UNO Dock for NanoPi NEO

From FriendlyELEC WiKi
Revision as of 08:04, 21 January 2017 by Yftan (Talk | contribs) (如何在UNO Dock for NanoPi NEO上使用Arduino)

Jump to: navigation, search

查看中文

1 Introduction

Matrix - UNO Dock for NanoPi NEO
  • The Matrix - UNO Dock for NanoPi NEO is a NanoHat Hub alike extension board.
  • It is an Arduino board compatible with Arduino UNO and works with Arduino programs.
  • The UNO Dock communicates with NanoPi NEO with I2C. The MEGA328P on the board acts as an interface between an external module connected to the board and the NanoPi NEO that is mounted on the board.When a NanoPi NEO and an Arduino module are connected to the UNO DOCK users can easily access the Arduino module from the NanoPi NEO.
  • It has an onboard USB to Serial port chip which allows users to set the serial port as either Arduino serial port or NanoPi NEO's debug port with a jumper
  • It has 12V power input to 5V/2A output.
  • NanoPi NEO can be directly mounted on the UNO Dock.

2 Hardware Spec

  • Arduino UNO supported
  • Onboard USB to Serial port (can be set as either Arduino serial port or NanoPi NEO’s debug port with a jumper)
  • 12V power input to 5V/2A output
  • 1 x 2.0mm pitch 4-Pin NEO-UART interface
  • 2 x 2.0mm pitch 4-Pin NEO-I2C interface
  • PCB dimension(mm): 110.2 x 53.3

Matrix - UNO Dock for NanoPi NEO_PCB.PCB

  • Pin Description:

3 Application with UNO Dock for NanoPi NEO

3.1 Connect NanoPi NEO to UNO Dock

Currently the UNO Dock works with the NanoPi NEO。
You can stack a NanoPi NEO to the UNO Dock. Here is a hardware setup:
Matrix-UNO_Dock_NEO

3.2 Install BakeBit Library

  • Step 1 - Connect your NanoPi NEO/AIR to the internet, open a terminal on your NanoPi NEO/AIR from SSH login and download the BakeBit source code from github:
cd  ~
git clone https://github.com/friendlyarm/BakeBit.git
  • Step 2 - Run the installation script for BakeBit Library:
cd BakeBit/Script
chmod +x install.sh
./install.sh
  • Step 3 - Reboot your board after installation is finished:
reboot
  • Step 4 - Verify BakeBit Functions:

Connect a BakeBit Starter Kit’s LED module to the NanoHat Hub's D3 interface and run the following command on the NanoPi NEO's command line:

python ~/BakeBit/Software/Python/grove_led_blink.py

If the LED is blinking your BakeBit is proved to be working.

4 Run Arduino on UNO Dock for NanoPi NEO

  • Step 1 jump the USB to Serial jumper to UNO-UART, connect your UNO Dock to a PC hose and power the board with a 12V DC power.
  • Step 2 check the Dock's serial port's number on the PC. In our test it was "COM1".

Matrix - UNO Dock for NanoPi COM

Set up your UNO Dock by following the steps below:
Go to 选择工具->开发板->Arduino Nano
Matrix - UNO Dock for NanoPi 环境配置
选择工具->端口->COM1(选择对应的计算机端口)
Matrix - UNO Dock for NanoPi 环境配置

  • Step 4 click on "upload"

After upload is done you can play with your UNO Dock.

5 注意

使用Arduino IDE软件下载程序后,如果回到NanoPi NEO上使用UNO Dock for NanoPi NEO,需要给UNO Dock for NanoPi NEO下载固件,固件源码已上传到github。
固件源码下载地址

6 相关资料