Matrix - Temperature Sensor

查看中文

1 Introduction

Temperature Sensor

• The matrix-temperature_sensor module is used to measure temperature.
• We utilitze the DS18B20 chip with the To-92 package in this module. Its unique 1-wire interface requires only 1 port pin for reading/writing. Power for reading, writing, and performing temperature conversions can be derived from the data line itself with no need for an external power source. The DS18B20 can be powered from its data line. Each DS18B20 is assigned a unique ID.
• Its temperature range is -55 degree Celsius to +125 degree Celsius. The thermometer resolution is programmable from 9 to 12 bits. When the measured temperature is between -10 degree Celsius to +85 degree Celsius the accuracy can be at 0.5 degree. Among all three DS18B20 pins V is power, G is ground and S is data.

2 Features

• -55 degree Celsius to +125 degree Celsius
• One wire interface for communication
• Tiny, easy to be deployed in various situations
• 2.54mm spacing pin
• PCB dimension(mm): 8 X 24

• Pin Description:

Pin	Description
S	GPIO
V	Supply Voltage 5V
G	Ground

3 Basic Device Operation

The core functionality of the DS18B20 is its direct-to-digital temperature sensor. The resolution of the DS18B20 is configurable (9, 10, 11, or 12 bits), with 12-bit readings the factory default state. This equates to a temperature resolution of 0.5°C, 0.25°C, 0.125°C, or 0.0625°C. Following the issuance of the Convert T [44h] command, a temperature conversion is performed and the thermal data is stored in the scratchpad memory in a 16-bit, sign-extended two’s complement format. The temperature information can be retrieved over the 1-Wire interface by issuing a Read Scratchpad [BEh] command once the conversion has been performed. The data is transferred over the 1-Wire bus, LSB first. The MSB of the temperature register contains the “sign” (S) bit, denoting whether the temperature is positive or negative.

4 Download Matrix Source Code

All the matrix modules' code samples are open source. They are maintained on GitHub - https://github.com/friendlyarm/matrix.git
Each branch in this hub contains the matrix modules' code samples for a board that the matrix modules can work with.

• The nanopi branch contains the matrix modules' code samples for the NanoPi
• The nanopi 2 branch contains the matrix modules' code samples for the NanoPi 2
• The tiny4412 branch contains the matrix modules' code samples for the Tiny4412
• The raspberrypi branch contains the matrix modules' code samples for the RaspberryPi

Please follow the steps below to get the source code:
Install the git utility on a PC running Ubuntu14.04

$ sudo apt-get install git

Clone the matrix code from GitHub

$ git clone https://github.com/friendlyarm/matrix.git

If this is successful a "matrix" directory will be generated, which will contain all the matrix modules' code samples.

5 与NanoPi 2连接使用

5.1 硬件连接

参考下图连接模块Matrix-Temperature_Sensor和NanoPi 2：

连接说明：

Matrix-Temperature Sensor	NanoPi 2
S	Pin7
V	Pin4
G	Pin6

5.2 编译测试程序

进入Matrix代码仓库，切换到nanopi2分支

$ cd matrix
$ git checkout nanopi2

编译Matrix配件代码

$ make CROSS_COMPILE=arm-linux- clean
$ make CROSS_COMPILE=arm-linux-
$ make CROSS_COMPILE=arm-linux- install

注意：请确保你的主机PC当前使用的交叉编译器为NanoPi 2配套的arm-linux-gcc-4.9.3。
编译成功后库文件位于install/lib目录下，而测试程序则位于install/usr/bin目录下，模块Matrix-Temperature_Sensor对应的测试程序为matrix-temp_sensor。
硬件驱动模块位于modules目录下，对应的驱动源码都包含在在NanoPi 2的Linux内核仓库里：https://github.com/friendlyarm/linux-3.4.y.git

5.3 运行测试程序

将带有Debian系统的SD卡插入一台运行Linux的电脑，可以挂载SD卡上的boot和rootfs分区。
假设rootfs分区的挂载路径为/media/rootfs，执行以下命令将Matrix的硬件驱动、库文件和测试程序拷贝到NanoPi 2的文件系统上。

$ cp modules /media/rootfs/ -r
$ cp install/lib/* /media/rootfs/lib/ -d
$ cp install/usr/bin/* /media/rootfs/usr/bin/

将SD卡重新插入NanoPi 2，上电启动，在Debian的shell终端中执行以下命令加载硬件驱动。

$ cd /modules
$ insmod w1-gpio.ko

运行模块Matrix-Temperature_Sensor的测试程序。

$ matrix-temp_sensor

运行效果如下：

5.4 代码展示

int main(int argc, char ** argv)
{
    char temperature[BUF_SIZE];
    memset(temperature, 0, BUF_SIZE);
    if (ds18b20Read(temperature) > 0) {
        printf("Temperature = %.3f C\n", atoi(temperature)/1000.0);
    } else {
        printf("Fail to get temperature\n");        
    }
    return 0;
}

6 Connect to NanoPi

6.1 Preparations

Please install a Debian on a NanoPi and an appropriate cross compiler on a PC. Please refer to wiki: NanoPi
Compile a NanoPi kernel. Note: please use the kernel's source code from the nanopi-v4.1.y-matrix branch

$ git clone https://github.com/friendlyarm/linux-4.x.y.git
$ cd linux-4.x.y
$ git checkout nanopi-v4.1.y-matrix
$ make nanopi_defconfig
$ touch .scmversion
$ make

6.2 Hardware Connection

Please refer to the following connection diagram to connect the Matrix-Temperature_Sensor module to the NanoPi

Connection Details:

Matrix-Temperature Sensor	NanoPi
S	Pin7
V	Pin4
G	Pin6

6.3 Compile Test Program

Please login the matrix hub and enter the nanopi branch

$ cd matrix
$ git checkout nanopi

Compile the matrix code

$ make CROSS_COMPILE=arm-linux- clean
$ make CROSS_COMPILE=arm-linux-
$ make CROSS_COMPILE=arm-linux- install

Note: please make sure to install the cross compiler "arm-linux-gcc-4.4.3" on your PC, which is used to compile files for the NanoPi-Debian.
Generated library files are under the "install/lib" directory. Applications are under the "install/usr/bin" directory. The test program for the "Matrix-Temperature_Sensor" module is "matrix-temperature_sensor".

6.4 Run Test Program

Please copy the library files and test program to the NanoPi

$ cp install/usr/bin/* nanopi_rootfs/usr/bin/
$ cp install/lib/* nanopi_rootfs/lib/ -d

Power on the NanoPi and run the following command in Debian's terminal
Note: this module is not plug and play therefore before running the module please make sure it is connected to a NanoPi.

$ matrix-temperature_sensor

6.5 Code Sample

int main(int argc, char ** argv)
{
    int devFD = -1;
    int pin = GPIO_PIN1;
    char *temperature = (char *) malloc(32);
    memset(temperature, 0, 32);
 
    if (argc == 2) {
        parseCmd(argc, argv, &pin);
    } else {
        printf("Using default pin GPIO_PIN1\n");
    }
 
    if ((devFD = ds18b20Init(pin)) == -1) {
        printf("Fail to init ds18b20\n");
        return -1;
    }
    if (ds18b20Read(temperature) > 0) {
        printf("Temperature = %s\n", temperature);
    } else {
        printf("Fail to get temperature\n");		
    }
    free(temperature);
    ds18b20DeInit(devFD);
    return 0;
}

7 Connect to Tiny4412

7.1 Preparations

Please refer to the Tiny4412's user's manual to install a UbuntuCore on the Tiny4412 and install an appropriate cross compiler on a PC.
Note: only the Tiny4412SDK-1506 carrier board can work with this module.

7.2 Hardware Connection

Please refer to the following diagram to connect the Matrix-Temperature_Sensor to the Tiny4412

Connection Details:

Matrix-Temperature Sensor	Tiny4412
S	GPIO1 S
V	GPIO1 5V
G	GPIO1 GND

7.3 Compile Test Program

Please login the Matrix hub and enter the matrix-tiny4412 branch

$ cd matrix
$ git checkout tiny4412

Compile the matrix code

$ make CROSS_COMPILE=arm-linux-gnueabihf- clean
$ make CROSS_COMPILE=arm-linux-gnueabihf-
$ make CROSS_COMPILE=arm-linux-gnueabihf- install

Note: please make sure to install the cross compiler "arm-linux-gnueabihf-gcc-4.7.3" on your PC, which is used to compile files for the Tiny4412-UbuntuCore.
Generated library files are under the "install/lib" directory. Applications are under the "install/usr/bin" directory. The test program for the "Matrix-Temperature_Sensor" module is "matrix-temperature_sensor".

7.4 Run Test Program

Please copy the library files and test program to the Tiny4412

$ cp install/usr/bin/* tiny4412_rootfs/usr/bin/
$ cp install/lib/* tiny4412_rootfs/lib/ -d

Power on the Tiny4412 and run the following command in UbuntuCore's terminal
Note: this module is not plug and play therefore before running the module please make sure it is connected to a Tiny4412.

$ matrix-temperature_sensor

7.5 Code Sample

int main(int argc, char ** argv)
{
    int devFD = -1;
    int pin = GPIO_PIN1;
    char *temperature = (char *) malloc(32);
    memset(temperature, 0, 32);
 
    if (argc == 2) {
        parseCmd(argc, argv, &pin);
    } else {
        printf("Using default pin GPIO_PIN1\n");
    }
 
    if ((devFD = ds18b20Init(pin)) == -1) {
        printf("Fail to init ds18b20\n");
        return -1;
    }
    if (ds18b20Read(temperature) > 0) {
        printf("Temperature = %s\n", temperature);
    } else {
        printf("Fail to get temperature\n");		
    }
    free(temperature);
    ds18b20DeInit(devFD);
    return 0;
}

10 Resources

DS18B20.pdf

11 Update Log

11.1 Feb-23-2016

• Added the description for "NanoPi 2 branch" in Section 4
• Added Section 5: Connect to NanoPi 2