Difference between revisions of "Matrix - I2C LCD1602 Keypad"

From FriendlyELEC WiKi
Jump to: navigation, search
(Introduction)
(Resources)
 
(55 intermediate revisions by 2 users not shown)
Line 2: Line 2:
  
 
==Introduction==
 
==Introduction==
[[File:LCD160201.png|thumb|I2C LCD1602]]
+
[[File:I2C LCD1602 Keypad.png|thumb|I2C LCD1602 Keypad]]
[[File:LCD160202.png|thumb|I2C LCD1602]]
+
[[File:I2C LCD1602 Keypad01.png|thumb|I2C LCD1602 Keypad]]
 
* The Matrix-I2C_LCD1602_Keypad module is an easy-to-use display module based on the LCD1602.
 
* The Matrix-I2C_LCD1602_Keypad module is an easy-to-use display module based on the LCD1602.
 
* This module integrates the LCD1602 and the MCP23017 module. It has five programmable keys which allow users to control the LCD1602's display and external devices connected to the module.
 
* This module integrates the LCD1602 and the MCP23017 module. It has five programmable keys which allow users to control the LCD1602's display and external devices connected to the module.
* 模块上的电位器是调节屏幕显示的灰度。
+
* It has a potentiometer to adjust the LCD's back light.
* LCD1602是可以显示16x2个字符的液晶显示屏,其本身是并行接口,需要较多的IO资源才可以与之通讯。使用IIC控制模块之后,只需要两根GPIO引脚即可。
+
* The LCD1602 can display up to 16x2 characters. It has a parallel interface. You can control it via two I2C channels.
* MCP23017带有串行接口的16 位远程双向I/O 扩展器,高速IIC接口,三个硬件地址引脚,最多可允许总线上连接8个器件。它可通过I2C与主控通讯,将主控发过来的数据信息转换成并行信号再转发给LCD1602,从而在实现LCD1602的显示和背光调节功能,达到节约IO资源和简化控制的目的。
+
* The MCP23017 has a 16-bit remote bidirectional I/O port, high speed I2C interface, three hardware address pins which make it able to connect up to eight devices. It communicates through I2C interface and converts input to parallel signals to the LCD1602.
  
==特性==
+
==Features==
* I2C通讯,显示和背光可控
+
* I2C interface, LCD display and backlight control
* 2.54mm排针接口,接线方便,通用性强
+
* 2.54mm spacing pin
* IIC模块PCB尺寸(mm):57x80
+
* I2C PCB dimension (mm): 57 x 80
* LCD1602 PCB尺寸(mm):36x80
+
* LCD1602 PCB dimension (mm): 36 x 80
[[File:lpdpcb01.png|frameless|400px|IIC扩展模块PCB]]
+
[[File:lpdpcb01.png|frameless|400px|IIC Module PCB]]
 
[[File:lcdpcb.png|frameless|400px|LCD1602 PCB]]
 
[[File:lcdpcb.png|frameless|400px|LCD1602 PCB]]
  
* 引脚说明:
+
* Pin Description:
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
|名称 || 描述
+
|Pin || Description
 
|-
 
|-
 
|IRQ    || BUTTON IRQ
 
|IRQ    || BUTTON IRQ
Line 29: Line 29:
 
|SCL    || I2C SCL
 
|SCL    || I2C SCL
 
|-  
 
|-  
|5V      || 电源5V
+
|5V      || Supply Voltage 5V
 
|-
 
|-
|GND    ||
+
|GND    || Ground
 
|}
 
|}
  
==工作原理==
+
==Basic Device Operation==
===MCP23017工作原理===
+
===MCP23017===
  
* MCP23017器件为IIC总线扩展,带有串行接口的16位远程双向I/O端口。系统主器件可通过写入I/O配置位将I/O使能为输入或输出,每个输入输出的数据都保存在对应的输入输出寄存器中,它为高速IIC接口,有三个硬件地址引脚,最多可允许总线上连接8个器件,具有两个可配置的中断引脚INTA和INTB。
+
* The MCP23017 has a 16-bit remote bidirectional I/O port, high speed I2C interface. These I/O can be configured to inputs and outputs. Each input/output data is kept in its register. It has three hardware address pins which make it able to connect up to eight devices. In addition it has two configurable interrupt pins INTA and INTB.
 +
* The I2C write operation includes the control byte and register address sequence. This sequence is followed by eight bits of data from the master and an Acknowledge (ACK) from the MCP23017. The operation is ended with a Stop (P) or Restart (SR) condition being generated by the master.
 +
* The I2C Read operation includes the control byte sequence. This sequence is followed by another control byte (including the Start condition and ACK) with the R/W bit set (R/W = 1). The MCP23017 then transmits the data contained in the addressed register. The sequence is ended with the master generating a Stop or Restart condition.
 +
* The I2C sequential operation (Write or Read) works this way: instead of transmitting a Stop or Restart condition after a data transfer, the master clocks the next byte pointed to by the address pointer after each data transfer. The sequence is ended with the master sending a Stop or Restart condition.
  
* I2C 写操作包括控制字节和寄存器地址序列,该序列后面跟随来自系统主器件的8 位数据和来自MCP23017 的应答(ACK)。该操作以主系统生成的停止(P)或重新启动(SR)条件结束。
+
===LCD1602===
* I2C读操作包括控制字节序列,该序列后跟R/W位置1(R/W = 1)的另一个控制字节(包括启动条件和ACK)。MCP23017 随后会发送被寻址寄存器中包含的数据。该序列以系统主器件生成停止或重新启动条件结束。
+
* The connection diagram between the MCP23017 module's Pin0~Pin7 and the LCD module is shown below:
* I2C 顺序写入/ 读取对于顺序操作(读操作或写操作),在完成数据传送后,系统主器件将发送地址指针指向的下一字节,而不是发送停止或重新启动条件。该序列以系统主器件发送停止或重新启动条件结束。MCP23017 地址指针在到达最后一个寄存器地址后,将返回到地址0。
+
[[File:图片不正确.png|frameless|400px|1602]]
 +
* RS is instruction/data register selection. RW is read/write selection. E is enable signal(edge triggering). BL is back light control. D4-D7 are data bits.
 +
* The LCD module is controlled by four data bits through which we can send instructions to control its state. Because it has eight instruction/data bits (DB7 - DB0) when writing each instruction/data we need to write the most significant four bits DB7 - DB4 first and then the least significant four bits DB3 - DB0.
 +
* Note: the LCD module has 192 most commonly used characters stored in CGROM. When we write a common character e.g "A" it will directly display "A". In addition it can store up to eight user defined characters in RAM called CGRAM.
  
===LCD1602工作原理===
+
==Applications==
* 由模块的原理图可以看出PCF8574模块的输出引脚P0-P7与LCD模块的引脚连接如下图:
+
===Connect to NanoPi M1===
[[File:1602.png|frameless|400px|1602]]
+
Refer to the following connection diagram to connect the module to the NanoPi M1:<br>
* RS为指令/数据控制位,RW为读/写控制位,E为使能位(边沿触发),BL为背光灯控制位,D4-D7为数据位。
+
[[File:Matrix-I2C_LCD1602_Keypad_nanopi_m1.jpg|frameless|600px|Matrix-I2C_LCD1602_Keypad_nanopi_m1]]
* 由于LCD用到四个数据位,因此只能使用4线来驱动。通过指令表我们可以对LCD进行写指令设置LCD的工作转态,但这里的指令/数据(DB7-DB0)是八位的,而LCD却是4线驱动,因此每次写指令/数据时是先写高四位(DB7-DB4),再写低四位(DB3-DB0)。
+
* 注意:LCD内置了192个常用字模,存放在CGROM,所以我们在显示字符A时可以直接写入“A”,此外LCD还有8个允许用户自定义的字符产生的RAM,称为CGRAM,这里由于没有涉及到所以不介绍,有兴趣的用户可以去了解一下。
+
  
==下载Matrix源码==
+
===Connect to NanoPi 2===
Matrix配件相关的代码是完全开源的,统一由一个仓库进行管理:git://github.com/friendlyarm/matrix.git <br>
+
Refer to the following connection diagram to connect the module to the NanoPi 2:<br>
该仓库里不同的分支代表着Matrix配件所支持的不同开发板。<br>
+
[[File:matrix-i2c_lcd1602_keypad_nanopi 2.jpg|frameless|600px|matrix-i2c_lcd1602_keypad_nanopi 2]]
* nanopi分支包含了Matrix对NanoPi的支持;
+
* tiny4412分支包含了Matrix对Tiny4412的支持;
+
* raspberrypi分支包含了Matrix对RaspberryPi的支持;
+
  
在主机PC上安装git,以Ubuntu14.04为例
+
===Connect to NanoPi M2 / NanoPi 2 Fire===
 +
Refer to the following connection diagram to connect the module to the NanoPi M2/ NanoPi 2 Fire.<br>
 +
[[File:Matrix-I2C_LCD1602_Keypad_nanopi_m2.jpg|frameless|600px|Matrix-I2C_LCD1602_Keypad_nanopi_m2]]
 +
 
 +
===Connect to NanoPC-T2===
 +
Refer to the following connection diagram to connect the module to the NanoPC-T2:<br>
 +
[[File:Matrix-I2C_LCD1602_Keypad_NanoPC-T2.jpg|frameless|600px|Matrix-I2C_LCD1602_Keypad_NanoPC-T2]]
 +
 
 +
Connection Details:
 +
{| class="wikitable"
 +
|-
 +
|Matrix-I2C_LCD1602_Keypad || NanoPC-T2
 +
|-
 +
|SDA    || Pin6
 +
|-
 +
|SCL    || Pin5
 +
|-
 +
|5V    || Pin29
 +
|-
 +
|GND    || Pin30
 +
|}
 +
 
 +
==Compile & Run Test Program==
 +
Boot your ARM board with Debian and copy the matrix code:
 +
<syntaxhighlight lang="bash">
 +
$ apt-get update && apt-get install git
 +
$ git clone https://github.com/friendlyarm/matrix.git
 +
</syntaxhighlight>
 +
If your cloning is done successfully a "matrix" directory will be generated.
 +
 
 +
Compile and install Matrix:
 +
<syntaxhighlight lang="bash">
 +
$ cd matrix
 +
$ make && make install
 +
</syntaxhighlight>
 +
 
 +
Run test program:
 +
<syntaxhighlight lang="bash">
 +
$ matrix-lcd1602_keypad
 +
</syntaxhighlight>
 +
Note: this module is not plug and play therefore before running the module please make sure it is connected to an ARM board.<br>
 +
Here is what you should observe:<br>
 +
[[File:matrix-lcd1602_keypad_result.png|frameless|600px|matrix-lcd1602_keypad_result]] <br>
 +
By default the LCD displays the current time. If you press F1 it will display the IP address. If you press F5 it will display the current time. Users can define the functions of F2, F3 and F4.<br>
 +
If the LCD doesn't show them clearly you can adjust the resistor to highlight the characters.
 +
 
 +
==Code Sample==
 +
This Matrix code sample can work with all the ARM boards mentioned in this module's wiki. The name of this code sample is "matrix-i2c_lcd1602_keypad". Here is its source code:
 +
<syntaxhighlight lang="c">
 +
int main(int argc, char ** argv)
 +
{
 +
    int devFD, board;
 +
    int keyValue = 0;
 +
    int lastKeyValue = -1;
 +
    int showDefault = 1;
 +
    int needClear = 1;
 +
    time_t lt;
 +
    char curTime[TIME_STR_BUFSIZE];
 +
    char preTime[TIME_STR_BUFSIZE];
 +
    int i2cDev = 0;
 +
   
 +
    if ((board = boardInit()) < 0) {
 +
        printf("Fail to init board\n");
 +
        return -1;
 +
    }
 +
   
 +
    if (argc == 2)
 +
        i2cDev = atoi(argv[1]);   
 +
    if ((devFD = LCD1602KeyInit(i2cDev)) == -1) {
 +
        printf("Fail to init LCD1602\n");
 +
        return -1;
 +
    }
 +
    LCD1602KeyClear(devFD);
 +
    printf("waiting key press...\n");
 +
    while (1) {
 +
        keyValue = LCD1602GetKey(devFD);
 +
        if (keyValue != lastKeyValue) {
 +
            lastKeyValue = keyValue;
 +
        } else if (showDefault != 1){
 +
            usleep(1000);
 +
            continue;
 +
        }
 +
        switch (keyValue) {
 +
        // F1
 +
        case 0x1e:
 +
            showDefault = 0;
 +
            LCD1602KeyClear(devFD);
 +
            LCD1602KeyDispStr(devFD, 0, 0, "#F1-IP address");
 +
            if (showIP(devFD, "eth0")) {
 +
                if (showIP(devFD, "wlan0")) {
 +
                    if (showIP(devFD, "usb0")) {
 +
                        showIP(devFD, "lo");
 +
                    }
 +
                }
 +
            }
 +
            break;
 +
            // F2   
 +
        case 0x1d:
 +
            showDefault = 0;
 +
            LCD1602KeyClear(devFD);
 +
            LCD1602KeyDispStr(devFD, 0, 0, "#F2-Your favor");
 +
            LCD1602KeyDispStr(devFD, 0, 1, "Come add it");
 +
            break;
 +
            // F3   
 +
        case 0x1b:
 +
            showDefault = 0;
 +
            LCD1602KeyClear(devFD);
 +
            LCD1602KeyDispStr(devFD, 0, 0, "#F3-Your idea");
 +
            LCD1602KeyDispStr(devFD, 0, 1, "Come show it");
 +
            break;
 +
            // F4
 +
        case 0x17:
 +
            showDefault = 0;
 +
            LCD1602KeyClear(devFD);
 +
            LCD1602KeyDispStr(devFD, 0, 0, "#F4-About");
 +
            LCD1602KeyDispStr(devFD, 0, 1, "by FriendlyARM");
 +
            break;
 +
            // F5
 +
        case 0xf:
 +
            showDefault = 1;
 +
            break;
 +
        }
 +
        if (showDefault == 1) {
 +
            if (needClear) {
 +
                LCD1602KeyClear(devFD);
 +
                LCD1602KeyDispStr(devFD, 0, 0, "#Default");
 +
                needClear = 0;
 +
            }
 +
            memset(curTime, 0, TIME_STR_BUFSIZE);
 +
            lt = time(NULL);
 +
            strncpy(curTime, ctime(&lt) + 11, 8);
 +
            if(strcmp(curTime, preTime)) {
 +
                printf("time:%s\n", curTime);
 +
                LCD1602KeyDispStr(devFD, 0, 1, curTime);
 +
            }
 +
            memset(preTime, 0, TIME_STR_BUFSIZE);
 +
            strcpy(preTime, curTime);
 +
        } else {
 +
            needClear = 1;
 +
            usleep(1000);
 +
        }
 +
    }   
 +
    printf("quit reading key press\n");
 +
    LCD1602KeyDeInit(devFD);
 +
    return 0;
 +
}
 +
</syntaxhighlight>
 +
For more details about this APIs called in this code sample refer to [[Matrix API reference manual]] <br>
 +
 
 +
<!---
 +
==Download Matrix Source Code==
 +
All the matrix modules' code samples are open source. They are maintained on GitHub - https://github.com/friendlyarm/matrix.git <br>
 +
Each branch in this hub contains the matrix modules' code samples for a board that the matrix modules can work with.<br>
 +
* The nanopi branch contains the matrix modules' code samples for the NanoPi
 +
* The nanopi2 branch contains the matrix modules' code samples for the NanoPi 2
 +
* the tiny4412 branch contains the matrix modules' code samples for the Tiny4412
 +
* the raspberrypi branch contains the matrix modules' code samples for the RaspberryPi
 +
 
 +
Please follow the steps below to get the source code:<br>
 +
Install the git utility on a PC running Ubuntu14.04
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
$ sudo apt-get install git
 
$ sudo apt-get install git
 
</syntaxhighlight>
 
</syntaxhighlight>
  
克隆Matrix配件代码仓库
+
Clone the matrix code from GitHub
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
$ git clone git://github.com/friendlyarm/matrix.git
+
$ git clone https://github.com/friendlyarm/matrix.git
 +
</syntaxhighlight>
 +
If this is successful a "matrix" directory will be generated, which will contain all the matrix modules' code samples.
 +
 
 +
==Connect to NanoPi 2==
 +
===Hardware Connection===
 +
Please refer to the following connection diagram to connect the Matrix-I2C_LCD1602_Keypad to the NanoPi 2:<br>
 +
[[File:matrix-i2c_lcd1602_keypad_nanopi 2.jpg|frameless|600px|matrix-i2c_lcd1602_keypad_nanopi 2]]
 +
 
 +
Connection Details:
 +
{| class="wikitable"
 +
|-
 +
|Matrix-I2C_LCD1602_Keypad || NanoPi 2     
 +
|-
 +
|SDA    || Pin3
 +
|-
 +
|SCL    || Pin5
 +
|-
 +
|5V    || Pin4
 +
|-
 +
|GND    || Pin6
 +
|}
 +
 
 +
===Compile Test Program===
 +
Please login the matrix hub and enter the nanopi2 branch
 +
<syntaxhighlight lang="bash">
 +
$ cd matrix
 +
$ git checkout nanopi2
 +
</syntaxhighlight>
 +
 
 +
Compile the Matrix code
 +
<syntaxhighlight lang="bash">
 +
$ make CROSS_COMPILE=arm-linux- clean
 +
$ make CROSS_COMPILE=arm-linux-
 +
$ make CROSS_COMPILE=arm-linux- install
 +
</syntaxhighlight>
 +
Note: please make sure to install the cross compiler "arm-linux-gcc-4.9.3" on your PC, which is used to compile files for the NanoPi 2.<br>
 +
Generated library files are under the "install/lib" directory. The test program is under the "install/usr/bin" directory.<br>
 +
The modules are under the "modules" directory. The driver's source code is in github: https://github.com/friendlyarm/linux-3.4.y.git <br>
 +
 
 +
===Run Test Program===
 +
Please insert a TF card which is flashed with Debian to a Linux host and mount its boot and rootfs sections.<br>
 +
We assume the rootfs is mounted to /media/rootfs then please run the following commands to copy the module, library and test program to the card.<br>
 +
<syntaxhighlight lang="bash">
 +
$ cp modules /media/rootfs/ -r
 +
$ cp install/lib/* /media/rootfs/lib/ -d
 +
$ cp install/usr/bin/* /media/rootfs/usr/bin/
 +
</syntaxhighlight>
 +
 
 +
Insert this TF card to your NanoPi 2, power on and run the following command to start the matrix-lcd1602_keypad program.<br>
 +
<syntaxhighlight lang="bash">
 +
$ matrix-lcd1602_keypad
 +
</syntaxhighlight>
 +
Note: this module is not plug and play therefore before running the module please make sure it is connected to a NanoPi 2.<br>
 +
Here is what you should expect:<br>
 +
[[File:matrix-lcd1602_keypad_result.png|frameless|600px|matrix-lcd1602_keypad_result]] <br>
 +
By default the LCD displays the current time. If you press F1 it will display the IP address. If you press F5 it will display the current time. Users can define the functions of F2, F3 and F4.
 +
 
 +
===Code Sample===
 +
<syntaxhighlight lang="c">
 +
int main(int argc, char ** argv)
 +
{
 +
    int devFD;
 +
    int keyValue = 0;
 +
    int lastKeyValue = -1;
 +
    int showDefault = 1;
 +
    int needClear = 1;
 +
    time_t lt;
 +
    char curTime[TIME_STR_BUFSIZE];
 +
    char preTime[TIME_STR_BUFSIZE];
 +
 
 +
    if ((devFD = LCD1602KeyInit()) == -1) {
 +
        printf("Fail to init LCD1602\n");
 +
        return -1;
 +
    }
 +
    LCD1602KeyClear(devFD);
 +
    printf("waiting key press...\n");
 +
 
 +
    while (1) {
 +
        keyValue = LCD1602GetKey(devFD);
 +
        if (keyValue != lastKeyValue) {
 +
            lastKeyValue = keyValue;
 +
        } else if (showDefault != 1){
 +
            usleep(1000);
 +
            continue;
 +
        }
 +
        switch (keyValue) {
 +
        // F1
 +
        case 0x1e:
 +
            showDefault = 0;
 +
            LCD1602KeyClear(devFD);
 +
            LCD1602KeyDispStr(devFD, 0, 0, "#F1-IP address");
 +
            if (showIP(devFD, "eth0")) {
 +
                if (showIP(devFD, "wlan0")) {
 +
                    if (showIP(devFD, "usb0")) {
 +
                        showIP(devFD, "lo");
 +
                    }
 +
                }
 +
            }
 +
            break;
 +
            // F2   
 +
        case 0x1d:
 +
            showDefault = 0;
 +
            LCD1602KeyClear(devFD);
 +
            LCD1602KeyDispStr(devFD, 0, 0, "#F2-Your favor");
 +
            LCD1602KeyDispStr(devFD, 0, 1, "Come add it");
 +
            break;
 +
            // F3   
 +
        case 0x1b:
 +
            showDefault = 0;
 +
            LCD1602KeyClear(devFD);
 +
            LCD1602KeyDispStr(devFD, 0, 0, "#F3-Your idea");
 +
            LCD1602KeyDispStr(devFD, 0, 1, "Come show it");
 +
            break;
 +
            // F4
 +
        case 0x17:
 +
            showDefault = 0;
 +
            LCD1602KeyClear(devFD);
 +
            LCD1602KeyDispStr(devFD, 0, 0, "#F4-About");
 +
            LCD1602KeyDispStr(devFD, 0, 1, "by FriendlyARM");
 +
            break;
 +
            // F5
 +
        case 0xf:
 +
            showDefault = 1;
 +
            break;
 +
        }
 +
        if (showDefault == 1) {
 +
            if (needClear) {
 +
                LCD1602KeyClear(devFD);
 +
                LCD1602KeyDispStr(devFD, 0, 0, "#Default");
 +
                needClear = 0;
 +
            }
 +
            memset(curTime, 0, TIME_STR_BUFSIZE);
 +
            lt = time(NULL);
 +
            strncpy(curTime, ctime(&lt) + 11, 8);
 +
            if(strcmp(curTime, preTime)) {
 +
                printf("time:%s\n", curTime);
 +
                LCD1602KeyDispStr(devFD, 0, 1, curTime);
 +
            }
 +
            memset(preTime, 0, TIME_STR_BUFSIZE);
 +
            strcpy(preTime, curTime);
 +
        } else {
 +
            needClear = 1;
 +
            usleep(1000);
 +
        }
 +
    }   
 +
    printf("quit reading key press\n");
 +
    LCD1602KeyDeInit(devFD);
 +
    return 0;
 +
}
 
</syntaxhighlight>
 
</syntaxhighlight>
克隆完成后会得到一个matrix目录,里面存放着所有Matrix配件的代码。
 
  
==与NanoPi连接使用==
+
==Connect to NanoPi==
===准备工作===
+
===Preparations===
在NanoPi上运行Debian系统,然后在主机PC上安装并使用相应的编译器。参考wiki:[[NanoPi/zh|NanoPi]] <br>
+
Please install a Debian on a NanoPi and an appropriate cross compiler on a PC. Please refer to wiki: [[NanoPi|NanoPi]] <br>
注意:必须使用nanopi-v4.1.y-matrix分支编译出来的内核。<br>
+
Compile a NanoPi kernel. Note: please use the kernel's source code from the nanopi-v4.1.y-matrix branch
下载NanoPi内核源代码并编译
+
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
$ git clone https://github.com/friendlyarm/linux-4.x.y.git
 
$ git clone https://github.com/friendlyarm/linux-4.x.y.git
Line 82: Line 389:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
===硬件连接===
+
===Hardware Connection===
参考下图连接模块Matrix-I2C_LCD1602_Keypad和NanoPi <br>
+
Please refer to the following connection diagram to connect the Matrix-I2C_LCD1602_Keypad to the NanoPi <br>
 
[[File:matrix-i2c_lcd1602_keypad_nanopi.jpg|frameless|600px|matrix-i2c_lcd1602_keypad_nanopi]]
 
[[File:matrix-i2c_lcd1602_keypad_nanopi.jpg|frameless|600px|matrix-i2c_lcd1602_keypad_nanopi]]
  
连接说明:
+
Connection Details:
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
Line 100: Line 407:
 
|}
 
|}
  
===编译测试程序===
+
===Compile Test Program===
进入Matrix代码仓库,切换到nanopi分支
+
Please login the matrix hub and enter the nanopi branch
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
$ cd matrix
 
$ cd matrix
Line 107: Line 414:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
编译Matrix配件代码
+
Compile the matrix code
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
$ make CROSS_COMPILE=arm-linux- clean
 
$ make CROSS_COMPILE=arm-linux- clean
Line 113: Line 420:
 
$ make CROSS_COMPILE=arm-linux- install
 
$ make CROSS_COMPILE=arm-linux- install
 
</syntaxhighlight>
 
</syntaxhighlight>
注意:请确保你的主机PC当前使用的交叉编译器为NanoPi-Debian配套的arm-linux-gcc.4.4.3。<br>
+
Note: please make sure to install the cross compiler "arm-linux-gcc-4.4.3" on your PC, which is used to compile files for the NanoPi-Debian.<br>
编译出来的库文件位于install/lib目录下,而测试程序则位于install/usr/bin目录下,模块Matrix-I2C_LCD1602_Keypad对应的测试程序为matrix-i2c_lcd1602_keypad。<br>
+
Generated library files are under the "install/lib" directory. Applications are under the "install/usr/bin" directory. The test program for the "Matrix-I2C_LCD1602_Keypad" module is "matrix-i2c_lcd1602_keypad".<br>
  
===运行测试程序===
+
===Run Test Program===
拷贝库文件和测试程序到NanoPi的文件系统上
+
Please copy the library files and test program to the NanoPi
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
$ cp install/usr/bin/* nanopi_rootfs/usr/bin/
 
$ cp install/usr/bin/* nanopi_rootfs/usr/bin/
Line 123: Line 430:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
然后启动NanoPi,在Debian的shell终端中执行如下命令运行模块Matrix-I2C_LCD1602_Keypad的测试程序 <br>
+
Power on the NanoPi and run the following command in Debian's terminal<br>
注意:此模块并不支持热插拔,启动系统前需要确保硬件正常连接。
+
Note: this module is not plug and play therefore before running the module please make sure it is connected to a NanoPi.
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
$ matrix-i2c_lcd1602_keypad
 
$ matrix-i2c_lcd1602_keypad
 
</syntaxhighlight>
 
</syntaxhighlight>
  
===代码展示===
+
===Code Sample===
 
<syntaxhighlight lang="c">
 
<syntaxhighlight lang="c">
 
int main(int argc, char ** argv)
 
int main(int argc, char ** argv)
Line 211: Line 518:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
==与Tiny4412连接使用==
+
==Connect to Tiny4412==
===准备工作===
+
===Preparations===
参考Tiny4412光盘里的《友善之臂Ubuntu使用手册》,在Tiny4412上运行UbuntuCore系统,然后在主机PC上安装并使用相应的编译器。<br>
+
Please refer to the Tiny4412's user's manual to install a UbuntuCore on the Tiny4412 and install an appropriate cross compiler on a PC.<br>
注意:只能使用Tiny4412SDK-1506的底板。
+
Note: only the Tiny4412SDK-1506 carrier board can work with this module.
  
===硬件连接===
+
===Hardware Connection===
参考下图连接模块Matrix-I2C_LCD1602_Keypad和Tiny4412 <br>
+
Please refer to the following diagram to connect the Matrix-I2C_LCD1602_Keypad to the Tiny4412<br>
 
[[File:matrix-i2c_lcd1602_keypad_tiny4412.jpg|frameless|400px|matrix-i2c_lcd1602_keypad_tiny4412]]
 
[[File:matrix-i2c_lcd1602_keypad_tiny4412.jpg|frameless|400px|matrix-i2c_lcd1602_keypad_tiny4412]]
 
<br>
 
<br>
连接说明:
+
Connection Details:
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
Line 226: Line 533:
 
|}
 
|}
  
===编译测试程序===
+
===Compile Test Program===
进入Matrix代码仓库,切换到tiny4412分支
+
Please login the Matrix hub and enter the matrix-tiny4412 branch
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
$ cd matrix
 
$ cd matrix
Line 233: Line 540:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
编译Matrix配件代码
+
Compile the Matrix code
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
$ make CROSS_COMPILE=arm-linux-gnueabihf- clean
 
$ make CROSS_COMPILE=arm-linux-gnueabihf- clean
Line 239: Line 546:
 
$ make CROSS_COMPILE=arm-linux-gnueabihf- install
 
$ make CROSS_COMPILE=arm-linux-gnueabihf- install
 
</syntaxhighlight>
 
</syntaxhighlight>
注意:请确保你的主机PC当前使用的交叉编译器为Tiny4412-UbuntuCore配套的arm-linux-gnueabihf-gcc-4.7.3。<br>
+
Note: please make sure to install the cross compiler "arm-linux-gnueabihf-gcc-4.7.3" on your PC, which is used to compile files for the Tiny4412-UbuntuCore.<br>
编译出来的库文件位于install/lib目录下,而测试程序则位于install/usr/bin目录下,模块Matrix-I2C_LCD1602_Keypad对应的测试程序为matrix-i2c_lcd1602_keypad。
+
Generated library files are under the "install/lib" directory. Applications are under the "install/usr/bin" directory. The test program for the "Matrix-I2C_LCD1602_Keypad" module is "matrix-i2c_lcd1602_keypad".
  
===运行测试程序===
+
===Run Test Program===
拷贝库文件和测试程序到Tiny4412的UbuntuCore的文件系统上
+
Please copy the library files and test program to the Tiny4412
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
$ cp install/usr/bin/* tiny4412_rootfs/usr/bin/
 
$ cp install/usr/bin/* tiny4412_rootfs/usr/bin/
Line 249: Line 556:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
然后启动Tiny4412,在UbuntuCore的shell终端中执行如下命令运行模块Matrix-I2C_LCD1602_Keypad的测试程序 <br>
+
Power on the Tiny4412 and run the following command in UbuntuCore's terminal <br>
注意:此模块并不支持热插拔,启动系统前需要确保硬件正常连接。
+
Note: this module is not plug and play therefore before running the module please make sure it is connected to a Tiny4412.
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
$ matrix-i2c_lcd1602_keypad
 
$ matrix-i2c_lcd1602_keypad
 
</syntaxhighlight>
 
</syntaxhighlight>
  
===代码展示===
+
===Code Sample===
 
<syntaxhighlight lang="c">
 
<syntaxhighlight lang="c">
 
int main(int argc, char ** argv)
 
int main(int argc, char ** argv)
Line 337: Line 644:
 
</syntaxhighlight>
 
</syntaxhighlight>
  
==与RaspberryPi连接使用==
+
==Connect to RaspberryPi==
  
==与Arduino连接使用==
+
==Connect to Arduino==
 +
--->
 +
==Resources==
 +
[http://ww1.microchip.com/downloads/en/DeviceDoc/21952b.pdf MCP23017.pdf]  <br>
 +
[https://www.openhacks.com/uploadsproductos/eone-1602a1.pdf LCD1602.pdf]
  
==相关资料==
+
==Update Log==
 +
===Feb-24-2016===
 +
* Added the driver's source code location in Section 5.2
 +
===June-19-2016===
 +
* Re-organized and simplified wiki

Latest revision as of 14:59, 19 June 2016

查看中文

1 Introduction

I2C LCD1602 Keypad
I2C LCD1602 Keypad
  • The Matrix-I2C_LCD1602_Keypad module is an easy-to-use display module based on the LCD1602.
  • This module integrates the LCD1602 and the MCP23017 module. It has five programmable keys which allow users to control the LCD1602's display and external devices connected to the module.
  • It has a potentiometer to adjust the LCD's back light.
  • The LCD1602 can display up to 16x2 characters. It has a parallel interface. You can control it via two I2C channels.
  • The MCP23017 has a 16-bit remote bidirectional I/O port, high speed I2C interface, three hardware address pins which make it able to connect up to eight devices. It communicates through I2C interface and converts input to parallel signals to the LCD1602.

2 Features

  • I2C interface, LCD display and backlight control
  • 2.54mm spacing pin
  • I2C PCB dimension (mm): 57 x 80
  • LCD1602 PCB dimension (mm): 36 x 80

IIC Module PCB LCD1602 PCB

  • Pin Description:
Pin Description
IRQ BUTTON IRQ
SDA I2C SDA
SCL I2C SCL
5V Supply Voltage 5V
GND Ground

3 Basic Device Operation

3.1 MCP23017

  • The MCP23017 has a 16-bit remote bidirectional I/O port, high speed I2C interface. These I/O can be configured to inputs and outputs. Each input/output data is kept in its register. It has three hardware address pins which make it able to connect up to eight devices. In addition it has two configurable interrupt pins INTA and INTB.
  • The I2C write operation includes the control byte and register address sequence. This sequence is followed by eight bits of data from the master and an Acknowledge (ACK) from the MCP23017. The operation is ended with a Stop (P) or Restart (SR) condition being generated by the master.
  • The I2C Read operation includes the control byte sequence. This sequence is followed by another control byte (including the Start condition and ACK) with the R/W bit set (R/W = 1). The MCP23017 then transmits the data contained in the addressed register. The sequence is ended with the master generating a Stop or Restart condition.
  • The I2C sequential operation (Write or Read) works this way: instead of transmitting a Stop or Restart condition after a data transfer, the master clocks the next byte pointed to by the address pointer after each data transfer. The sequence is ended with the master sending a Stop or Restart condition.

3.2 LCD1602

  • The connection diagram between the MCP23017 module's Pin0~Pin7 and the LCD module is shown below:

1602

  • RS is instruction/data register selection. RW is read/write selection. E is enable signal(edge triggering). BL is back light control. D4-D7 are data bits.
  • The LCD module is controlled by four data bits through which we can send instructions to control its state. Because it has eight instruction/data bits (DB7 - DB0) when writing each instruction/data we need to write the most significant four bits DB7 - DB4 first and then the least significant four bits DB3 - DB0.
  • Note: the LCD module has 192 most commonly used characters stored in CGROM. When we write a common character e.g "A" it will directly display "A". In addition it can store up to eight user defined characters in RAM called CGRAM.

4 Applications

4.1 Connect to NanoPi M1

Refer to the following connection diagram to connect the module to the NanoPi M1:
Matrix-I2C_LCD1602_Keypad_nanopi_m1

4.2 Connect to NanoPi 2

Refer to the following connection diagram to connect the module to the NanoPi 2:
matrix-i2c_lcd1602_keypad_nanopi 2

4.3 Connect to NanoPi M2 / NanoPi 2 Fire

Refer to the following connection diagram to connect the module to the NanoPi M2/ NanoPi 2 Fire.
Matrix-I2C_LCD1602_Keypad_nanopi_m2

4.4 Connect to NanoPC-T2

Refer to the following connection diagram to connect the module to the NanoPC-T2:
Matrix-I2C_LCD1602_Keypad_NanoPC-T2

Connection Details:

Matrix-I2C_LCD1602_Keypad NanoPC-T2
SDA Pin6
SCL Pin5
5V Pin29
GND Pin30

5 Compile & Run Test Program

Boot your ARM board with Debian and copy the matrix code:

$ apt-get update && apt-get install git
$ git clone https://github.com/friendlyarm/matrix.git

If your cloning is done successfully a "matrix" directory will be generated.

Compile and install Matrix:

$ cd matrix
$ make && make install

Run test program:

$ matrix-lcd1602_keypad

Note: this module is not plug and play therefore before running the module please make sure it is connected to an ARM board.
Here is what you should observe:
matrix-lcd1602_keypad_result
By default the LCD displays the current time. If you press F1 it will display the IP address. If you press F5 it will display the current time. Users can define the functions of F2, F3 and F4.
If the LCD doesn't show them clearly you can adjust the resistor to highlight the characters.

6 Code Sample

This Matrix code sample can work with all the ARM boards mentioned in this module's wiki. The name of this code sample is "matrix-i2c_lcd1602_keypad". Here is its source code:

int main(int argc, char ** argv)
{
    int devFD, board;
    int keyValue = 0;
    int lastKeyValue = -1;
    int showDefault = 1;
    int needClear = 1;
    time_t lt;
    char curTime[TIME_STR_BUFSIZE];
    char preTime[TIME_STR_BUFSIZE];
    int i2cDev = 0;
 
    if ((board = boardInit()) < 0) {
        printf("Fail to init board\n");
        return -1;
    }
 
    if (argc == 2)
        i2cDev = atoi(argv[1]);    
    if ((devFD = LCD1602KeyInit(i2cDev)) == -1) {
        printf("Fail to init LCD1602\n");
        return -1;
    }
    LCD1602KeyClear(devFD);
    printf("waiting key press...\n");
    while (1) {
        keyValue = LCD1602GetKey(devFD);
        if (keyValue != lastKeyValue) {
            lastKeyValue = keyValue;
        } else if (showDefault != 1){
            usleep(1000);
            continue;
        }
        switch (keyValue) {
        // F1
        case 0x1e:
            showDefault = 0;
            LCD1602KeyClear(devFD);
            LCD1602KeyDispStr(devFD, 0, 0, "#F1-IP address");
            if (showIP(devFD, "eth0")) {
                if (showIP(devFD, "wlan0")) {
                    if (showIP(devFD, "usb0")) {
                        showIP(devFD, "lo");
                    }
                }
            }
            break;
            // F2    
        case 0x1d:
            showDefault = 0;
            LCD1602KeyClear(devFD);
            LCD1602KeyDispStr(devFD, 0, 0, "#F2-Your favor");
            LCD1602KeyDispStr(devFD, 0, 1, "Come add it");
            break;
            // F3    
        case 0x1b:
            showDefault = 0;
            LCD1602KeyClear(devFD);
            LCD1602KeyDispStr(devFD, 0, 0, "#F3-Your idea");
            LCD1602KeyDispStr(devFD, 0, 1, "Come show it");
            break;
            // F4
        case 0x17:
            showDefault = 0;
            LCD1602KeyClear(devFD);
            LCD1602KeyDispStr(devFD, 0, 0, "#F4-About");
            LCD1602KeyDispStr(devFD, 0, 1, "by FriendlyARM");
            break;
            // F5
        case 0xf:
            showDefault = 1;
            break;
        }
        if (showDefault == 1) {
            if (needClear) {
                LCD1602KeyClear(devFD);
                LCD1602KeyDispStr(devFD, 0, 0, "#Default");
                needClear = 0;
            }
            memset(curTime, 0, TIME_STR_BUFSIZE);
            lt = time(NULL);
            strncpy(curTime, ctime(&lt) + 11, 8);
            if(strcmp(curTime, preTime)) {
                printf("time:%s\n", curTime);
                LCD1602KeyDispStr(devFD, 0, 1, curTime);
            }
            memset(preTime, 0, TIME_STR_BUFSIZE);
            strcpy(preTime, curTime);
        } else {
            needClear = 1;
            usleep(1000);
        }
    }    
    printf("quit reading key press\n");
    LCD1602KeyDeInit(devFD);
    return 0;
}

For more details about this APIs called in this code sample refer to Matrix API reference manual

7 Resources

MCP23017.pdf
LCD1602.pdf

8 Update Log

8.1 Feb-24-2016

  • Added the driver's source code location in Section 5.2

8.2 June-19-2016

  • Re-organized and simplified wiki