Matrix - Buzzer

From FriendlyELEC WiKi
Revision as of 10:28, 25 September 2015 by Yftan (Talk | contribs) (下载Matrix源码)

Jump to: navigation, search

查看中文

1 Introduction

Buzzer
  • The Matrix-Buzzer is a passive buzzer. To drive this buzzer an oscillating source generating 2K - 5K square waves is needed.
  • It can be used in electronic devices that need sound generators.

2 Features

  • 3 PIN interface
  • PCB dimension (mm): 16 x 24

无源蜂鸣器PCB

  • Pin Description:
Pin Description
V Supply Voltage 5V
G Ground
S PWM Input

3 Basic Device Operation

A passive buzzer will not tweet if DC signals are used; instead, you need to use square waves whose frequency is between 2K and 5K to drive it. If you use GPIO signals to drive it you need to pull the GPIO high first and then low to generate oscillation. The oscillation frequency is generated by the time in which GPIO signals turn from high to low. The buzzer will generate different sounds based on different frequencies.

4 Download Matrix Source Code

All the matrix modules' code samples are open source. They are maintained on GitHub - git://github.com/friendlyarm/matrix.git
Each branch in this hub contains the matrix modules' code samples for a board that the matrix modules can work with.

  • The nanopi branch contains the matrix modules' code samples for the NanoPi
  • The tiny4412 branch contains the matrix modules' code samples for the Tiny4412
  • The raspberrypi branch contains the matrix modules' code samples for the RaspberryPi

Please follow the steps below to get the source code:
Install the git utility on a PC running Ubuntu14.04

$ sudo apt-get install git

Clone the matrix code from GitHub

$ git clone git://github.com/friendlyarm/matrix.git

If this is successful a "matrix" directory will be generated, which will contain all the matrix modules' code samples.

5 与NanoPi连接使用

5.1 准备工作

在NanoPi上运行Debian系统,然后在主机PC上安装并使用相应的编译器。参考wiki:NanoPi
注意:必须使用nanopi-v4.1.y-matrix分支编译出来的内核。
下载NanoPi内核源代码并编译

$ git clone https://github.com/friendlyarm/linux-4.x.y.git
$ cd linux-4.x.y
$ git checkout nanopi-v4.1.y-matrix
$ make nanopi_defconfig
$ touch .scmversion
$ make

5.2 硬件连接

参考下图连接模块Matrix-Buzzer和NanoPi
matrix-buzzer_nanopi

连接说明:

Matrix-Buzzer NanoPi
G Pin6
V Pin4
S Pin22

5.3 编译测试程序

进入Matrix代码仓库,切换到nanopi分支

$ cd matrix
$ git checkout nanopi

编译Matrix配件代码

$ make CROSS_COMPILE=arm-linux- clean
$ make CROSS_COMPILE=arm-linux-
$ make CROSS_COMPILE=arm-linux- install

注意:请确保你的主机PC当前使用的交叉编译器为NanoPi-Debian配套的arm-linux-gcc-4.4.3。
编译出来的库文件位于install/lib目录下,而测试程序则位于install/usr/bin目录下,模块Matrix-Buzzer对应的测试程序为matrix-buzzer。

5.4 运行测试程序

拷贝库文件和测试程序到NanoPi的文件系统上

$ cp install/usr/bin/* nanopi_rootfs/usr/bin/
$ cp install/lib/* nanopi_rootfs/lib/ -d

然后启动NanoPi,在Debian的shell终端中执行如下命令运行模块Matrix-Buzzer的测试程序

$ matrix-buzzer

5.5 代码展示

int main(int argc, char ** argv)
{
    int pin = PWM_PIN1;
    int Hz;
    int duty;
 
    if (argc == 4) {
        if (parseCmd(argc, argv, &pin, &Hz, &duty) == -1) {
            return -1;
        }
    } else {
        Hz = 1000;
        duty = 500;
        printf("Usage:%s PWM[0~1] freq duty[0~1000]\n", argv[0]);
        printf("Using default config: pin=PWM0 freq=%dHz duty=%d\n", Hz, duty);
    }
 
    if (PWMPlay(pin, Hz, duty) == -1) {
        printf("Fail to output PWM\n");
    }  
    printf("Press enter to stop PWM\n");
    getchar();
    PWMStop(pin);
    printf("Stopped PWM\n");
    return 0;
}

6 与Tiny4412连接使用

6.1 准备工作

参考Tiny4412光盘里的《友善之臂Ubuntu使用手册》,在Tiny4412上运行UbuntuCore系统,然后在主机PC上安装并使用相应的编译器。
注意:只能使用Tiny4412SDK-1506的底板。

6.2 硬件连接

参考下图连接模块Matrix-Buzzer和Tiny4412
matrix-buzzer_tiny4412

连接说明:

Matrix-Buzzer Tiny4412
G GPIO1 GND
V GPIO1 5V
S GPIO11 S

6.3 编译测试程序

进入Matrix代码仓库,切换到tiny4412分支

$ cd matrix
$ git checkout tiny4412

编译Matrix配件代码

$ make CROSS_COMPILE=arm-linux-gnueabihf- clean
$ make CROSS_COMPILE=arm-linux-gnueabihf-
$ make CROSS_COMPILE=arm-linux-gnueabihf- install

注意:请确保你的主机PC当前使用的交叉编译器为Tiny4412-UbuntuCore配套的arm-linux-gnueabihf-gcc-4.7.3。
编译出来的库文件位于install/lib目录下,而测试程序则位于install/usr/bin目录下,模块Matrix-Buzzer对应的测试程序为matrix-buzzer。

6.4 运行测试程序

拷贝库文件和测试程序到Tiny4412的UbuntuCore的文件系统上

$ cp install/usr/bin/* tiny4412_rootfs/usr/bin/
$ cp install/lib/* tiny4412_rootfs/lib/ -d

然后启动Tiny4412,在UbuntuCore的shell终端中执行如下命令运行模块Matrix-Buzzer的测试程序

$ matrix-buzzer

6.5 代码展示

int main(int argc, char ** argv)
{
    int pin = PWM_PIN1;
    int Hz;
    int duty;
 
    if (argc == 4) {
        if (parseCmd(argc, argv, &pin, &Hz, &duty) == -1) {
            return -1;
        }
    } else {
        Hz = 1000;
        duty = 500;
        printf("Usage:%s PWM[0~1] freq duty[0~1000]\n", argv[0]);
        printf("Using default config: pin=PWM0 freq=%dHz duty=%d\n", Hz, duty);
    }
 
    if (PWMPlay(pin, Hz, duty) == -1) {
        printf("Fail to output PWM\n");
    }  
    printf("Press enter to stop PWM\n");
    getchar();
    PWMStop(pin);
    printf("Stopped PWM\n");
    return 0;
}

7 与RaspberryPi连接使用

8 与Arduino连接使用

9 相关资料