How to use overlayfs on Linux
Contents
1 What Is OverlayFS
OverlayFS is a union mount filesystem implementation for Linux. It allows a virtual merge of two partitions, while keeping their actual contents separate. One partition is the rootfs partition and the other is the data partition. It has the following advantages:
1) you can easily restore a system's factory settings by formatting the data partition;
2) you can still boot your system since the rootfs is read-only even when the data partition cannot be correctly mounted due to unexpected shutdown.
2 FriendlyELEC's Systems That Support OverlayFS
2.1 Hardware Systems
H3, H5, S5P4418, S5P6818, RK3399 based boards
2.2 OS Systems
FriendlyCore, FriendlyDesktop, Lubuntu
3 How to Check Whether OverlayFS Is Working
Run the df command. If the "/" partition is mounted as "overlay" it means OverlayFS is working;
pi@NanoPi-M1-Plus:~$ df Filesystem 1K-blocks Used Available Use% Mounted on udev 474848 0 474848 0% /dev tmpfs 102304 3564 98740 4% /run overlay 28925547 1315493 26112465 5% / tmpfs 511512 0 511512 0% /dev/shm tmpfs 5120 4 5116 1% /run/lock tmpfs 511512 0 511512 0% /sys/fs/cgroup /dev/mmcblk0p1 40862 11852 29010 30% /boot tmpfs 102304 0 102304 0% /run/user/1000
4 Partition Settings With OverlayFS
If OverlayFS is enabled in your system there will be three partitions:rootfs, data and boot, and these partitions correspond to a rootfs.img, a userdata.img and a boot.img separately:
root@NanoPi-M1-Plus:~# lsblk /dev/mmcblk0 NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT mmcblk0 179:0 0 29.7G 0 disk |-mmcblk0p2 179:2 0 1.2G 0 part |-mmcblk0p3 179:3 0 28.5G 0 part `-mmcblk0p1 179:1 0 40M 0 part /boot
The system data will be in the rootfs partition and the data written to the root directory will be in the data partition.
5 Restore Factory Settings With OverlayFS
5.1 Method 1: Operate in Userdata Partition
factory reset:
mount /dev/mmcblk0p3 /media/ && cd /media/ mv root/ deleteme.root mv work/ deleteme.work reboot
cleanup after reboot:
mount /dev/mmcblk0p3 /media/ && rm -rf /media/deleteme.*
5.2 Method 2: Restore by Setting Commandline Parameters
5.3 S5P4418 & S5P6818 platform
Add "wipedata=yes" to the kernel's commandline parameters. For S5P4418 and S5P6818 based boards you can do it after system boots;
5.3.1 恢复出厂设置
sudo fw_setenv bootargs "`sed 's/ wipedata=yes//g;s/ wipedata=no//g' /proc/cmdline` wipedata=yes" sudo reboot
5.3.2 Keep Data in Data Partition on System Reboot
sudo fw_setenv bootargs "`sed 's/ wipedata=yes//g;s/ wipedata=no//g' /proc/cmdline` wipedata=no" sudo reboot
For other SoC based boards you need to make changes in the kernel commandline by following the methods supported by their BSPs or by entering uboot to proceed.
6 Disable OverlayFS
If you have an installation TF card, use the fdisk command to delete the data partition.
