BakeBit - Buzzer/zh

English

1 介绍

Buzzer

• BakeBit - Buzzer是一个无源蜂鸣器模块，无源蜂鸣器内部有音圈和钼片，输入2.7KHz的PWM信号时，PWM信号通过绕在支架上的线包在支架的芯柱上产生一交变的磁通，交变的磁通和磁环恒定磁通进行叠加，使钼片以给定的PWM信号频率振动并配合共振腔发声。
• 通过调整输入PWM信号的频率即可使无源蜂鸣器发出频率不同的声音。
• 广泛应用于计算机、报警器、电子玩具、汽车电子设备、定时器等电子产品中作发声器件。

2 特性

• 使用标准的2.0mm 4 Pin BakeBit接口
• PWM信号输入
• PCB尺寸（mm）：20x24

• 引脚说明:

名称	描述
GND	电源5V
5V	地
NC	空
SIG	输入，接PWM

3 示例程序：Button And Buzzer

本示例需要配合BakeBit - Button使用。

3.1 硬件连接

简单的将 蜂鸣器 模块插入 D3接口，将 按键 插入 D4 接口，如下面这样：

3.2 示例源代码

import time
from bakebit import *
import math
 
buzzer_pin = 3		#Port for buzzer
button = 4		#Port for Button
old_button_status = -1
pinMode(buzzer_pin,"OUTPUT")	# Assign mode for buzzer as output
pinMode(button,"INPUT")		# Assign mode for Button as input
 
buzzer_on = False
old_buzzer_on = not buzzer_on
button_pressed = False
 
while True:
	try:
		while True:
			button_status = digitalRead(button)	#Read the Button status
			# print button_status
			if old_button_status < 0: 
				break
 
			if button_status != old_button_status:
				break
 
		time.sleep(0.2)
		old_button_status = button_status
 
		if button_status == 0:
			button_pressed = True
		else:
			if button_pressed:
				buzzer_on = not buzzer_on
			button_pressed = False 
 
		if old_buzzer_on != buzzer_on:
			old_buzzer_on = buzzer_on
			if buzzer_on:
				analogWrite(buzzer_pin,127)
				print "Buzzing"
			else:
				analogWrite(buzzer_pin,0)
				print "\tOff"			
 
		time.sleep(0.2)			
	except KeyboardInterrupt:	# Stop the buzzer before stopping
		digitalWrite(buzzer_pin,0)
		break
	except (IOError,TypeError) as e:
		print("Error")

Github

3.3 运行示例

假设你已经参考bakebit教程安装了BakeBit源代码，
要运行示例程序，可以在开发板上进入 BakeBit/Software/Python目录,运行bakebit_prj_Button_And_Buzzer.py:

cd ~/BakeBit/Software/Python
sudo python bakebit_prj_Button_And_Buzzer.py

3.4 运行结果

当按下按键时，蜂鸣器会响起，松开按键时，蜂鸣器停止。

4 相关资料

• [Schematic](BakeBit - Buzzer.pdf)
• [BakeBit Github项目](https://github.com/friendlyarm/BakeBit)
• [BakeBit Starter Kit手册](http://wiki.friendlyarm.com/bakebit/bakebit_starter_kit_manual_cn.pdf)