Smart4418 SDK

查看中文

1 Introduction

Overview

Front

The Smart4418 SDK carrier board V1606 has various interfaces and ports like HDMI port, USB host, SD card slot, SB9 serial port, RJ-45 Ethernet port, 3.5mm audio jack, SATA interface, MiniPCIe, MicroSIM etc with support for 3G/4G Bluetooth & WiFi.In addition it has hardware resources like buzzer, user keys, RTC battery, microphone and etc for users to evaluate its performance and features. FriendlyARM designed it for sake of industrial applications by putting all commonly used interfaces and ports on one side with mounting holes for easy deployment.
To make this carrier board applicable in various applications compared to our existing carrier boards we add more interfaces and ports such as DVP camera interface, SPI, GPIO, I2C, AP6212 WiFi & Bluetooth module, porcelain antenna, RTC seat and etc.

2 资源特性

Features

SDK Carrier Board Model	Smart4418SDK 1606
Dimension	189.8 x 118.2(mm)
Applicable CPU Board	Smart4418
WiFi/Bluetooth	Onboard WiFi & Bluetooth
MiniPCIe Interface	For 4G modules, data service only, speech service not applicable
SIM Card Slot	Pop-up MicroSIM card slot
Antenna	Onboard porcelain antenna
DVP Camera Interface	24pin, 0.5mm pitch FPC seat DVP Camera interface, ITU-R BT 601/656 8-bit
HDMI Interface	1 x HDMI A Type, HDMI 1.4a (Smart4418) 1080p30 video output
RS232 Serial Interface	2 x 3-wire serial port (UART0 and 3), DB9 male connector
USB Host	2 x USB A brought out from USB 2.0 hub, (USB 1.1 compatible)
USB Slave	1 x Micro USB, data communication only
Audio Interface	Internal Audio supports audio recording and play 3.5mm audio jack and MIC onboard Microphone
Ethernet	Internal 1000/100/10M Ethernet
User Key	PWRKEY (power key) RST (reset) K1/K2/K3 programmable keys
LED	2 x GPIO LED (On Smart4418 CPU board)
RTC	Onboard RTC battery(CR1220)
Buzzer	1 x PWM buzzer
SPI Interface	CON3: 26pin ,2.54mm pitch double row pin-header
GPIO座子	GPIOC9、GPIOC10、GPIOC11、GPIOC12
SD卡座	弹出式SD卡座
I2C扩展接口	I2C0
UART串口接口	UART2
SATA接口	板载SATA接口
SATA电源接口	板载SATA电源接口
LCD接口	LCD接口座(45pin, 0.5mm间距FPC贴片座) 支持一线触摸支持背光可调支持电容触摸屏支持RGB888模式支持全彩TFT CD
LCD固定孔	适用于X710 LCD模块
LVDS接口	2pin, 2.0mm间据
GPIO接口	30pin 2.0mm双排针, 包含1个UART, 1个I2C, 1个SPI, 1路SDIO, 11个GPIO
其它	板载1个EEPROM, 1个三轴加速度传感器
供电	DC 9V~24V/2A, 当使用SATA或LVDS背光时, 必须12V/3A供电

3 接口描述和尺寸

3.1 接口描述

LVDS接口

Pin#	Name	Pin#	Name
1	SYS_3.3V	2	SYS_3.3V
3	GPIOC16	4	GPIOB18
5	DGND	6	DGND
7	LVDS_D0-	8	LVDS_D0+
9	LVDS_D1-	10	LVDS_D1+
11	LVDS_D2-	12	LVDS_D2+
13	DGND	14	DGND
15	LVDS_CLK-	16	LVDS_CLK+
17	LVDS_D3-	18	LVDS_D3+
19	I2C2_SCL	20	I2C2_SDA

DVP摄像头接口

Pin#	Name
1, 2	SYS_3.3V
7,9,13,15,24	DGND
3	I2C0_SCL
4	I2C0_SDA
5	GPIOB14
6	GPIOB16
8,10	NC
11	VSYNC
12	HREF
14	PCLK
16-23	Data bit7-0

LCD接口

Pin#	Name	Description
1, 2	VDD_5V	5V输出, 可以给LCD模组供电
11，20，29, 37，38，39，40, 45	DGND	参考地, 0电位
3-10	Blue LSB to MSB	RGB的蓝色信号
12-19	Green LSB to MSB	RGB的绿色信号
21-28	Red LSB to MSB	RGB的红色信号
30	GPIOB25	普通GPIO, 用户可控制
31	GPIOC15	一线协议信号, 以实现LCD型号识别, 背光控制和电阻触摸的功能. 系统已占用, 用户不可重新设置.
32	XnRSTOUT Form CPU	系统复位时向外输出低电平
33	VDEN	指示RGB信号有效的信号
34	VSYNC	场信号
35	HSYNC	行信号
36	LCDCLK	LCD频率, Pixel frequency
41	I2C2_SCL	I2C2的时钟信号, 用来传输电容屏触摸数据
42	I2C2_SDA	I2C2的数据信号, 用来传输电容屏触摸数据
43	GPIOC16	电容触摸中断信号, 配合I2C2使用
44	NC	没有任何连接