Matrix - One Touch Sensor

查看中文

1 Introduction

• The Matrix One_Touch_Sensor is a digital one capacitive touch key module. It uses the one key capacitive touch pad detector IC TTP223. It has a touch key with stable touching detection. It is designed for replacing traditional direct button key with diverse pad size.By default it outputs low. When a finger touches the touch key it outputs high.

2 Features

• Standard 3Pin interface
• PCB dimension(mm): 16 x 24

• Pin Description:

Pin	Description
S	GPIO
V	Supply Voltage 5V
G	Ground

3 Basic Device Operation

The TTP223 is a one key capacitive touch pad detector IC. It measures changes of electric charges stored in the touch pad electrode with parasitic capacitance attached to an insulator :acrylic, glass, porcelain, wood and etc.

4 Applications

4.1 Connect to NanoPi M1

Refer to the following connection diagram to connect the module to the NanoPi M1:

Connection Details:

Matrix-One_Touch_Sensor	NanoPi M1
S	Pin7
V	Pin4
G	Pin6

4.2 Connect to NanoPi 2

Refer to the following connection diagram to connect the module to the NanoPi 2:
Matrix-One_Touch_Sensor_nanopi_2

Connection Details:

Matrix-One_Touch_Sensor	NanoPi 2
S	Pin7
V	Pin4
G	Pin6

4.3 Connect to NanoPi M2 / NanoPi 2 Fire

Refer to the following connection diagram to connect the module to the NanoPi M2/ NanoPi 2 Fire.

Connection Details:

Matrix-One_Touch_Sensor	NanoPi M2
S	Pin7
V	Pin4
G	Pin6

4.4 Connect to NanoPC-T2

Refer to the following connection diagram to connect the module to the NanoPC-T2:
Matrix-One_Touch_Sensor_NanoPC-T2

Connection Details:

Matrix-One_Touch_Sensor	NanoPC-T2
S	Pin15
V	Pin29
G	Pin30

5 Compile & Run Test Program

Boot your ARM board with Debian and copy the matrix code:

$ apt-get update && apt-get install git
$ git clone https://github.com/friendlyarm/matrix.git

If your cloning is done successfully a "matrix" directory will be generated.

Compile and install Matrix:

$ cd matrix
$ make && make install

Run test program:

$ matrix-gpio_int

Note: this module is not plug and play therefore before running the module please make sure it is connected to an ARM board.
Here is what you should observe:

Waiting event...
Device[0] value is 1

When you touch the module's active area an event will be triggered and detected.

6 Code Sample

This Matrix code sample can work with all the ARM boards mentioned in this module's wiki. The name of this code sample is "matrix-gpio_int". Here is its source code:

int main(int argc, char ** argv)
{
    int i, board;
    int retSize = -1;
    char value[ARRAY_SIZE(dev)];
 
    if ((board = boardInit()) < 0) {
        printf("Fail to init board\n");
        return -1;
    }
 
    if (argc == 2)
        dev[0].pin = atoi(argv[1]);
    system("modprobe "DRIVER_MODULE);
    signal(SIGINT, intHandler);
    if (board == BOARD_NANOPI_T2)
        dev[0].pin = GPIO_PIN(15);
    printf("Use GPIO_PIN(%d)\n", dev[0].pin);
    if ((devFD =sensorInit(dev, ARRAY_SIZE(dev))) == -1) {
        printf("Fail to init sensor\n");
        goto err;
    }
    printf("Waiting event...\n");
    if ((retSize = sensorRead(devFD, value, ARRAY_SIZE(dev))) == -1) {
        printf("Fail to read sensors\n");
    }
    if (retSize > 0) {
        i = 0;
        for (i=0; i<retSize; i++) {
            printf("Device[%d] value is %d\n", i, value[i]);
        }
    }
    sensorDeinit(devFD);
err:    
    system("rmmod "DRIVER_MODULE);
    return 0;
}

For more details about this APIs called in this code sample refer to Matrix API reference manual

8 Update Log

8.1 June-22-2016

• Created English wiki