Matrix - LED

From FriendlyELEC WiKi
Revision as of 07:28, 23 February 2016 by Yftan (Talk | contribs) (Undo revision 3776 by Yftan (talk))

Jump to: navigation, search

查看中文

1 Introduction

LED
LED
LED

The Matrix-LED is an LED module with three 2.54 mm spacing pins: V(supply voltage),G(ground) and S(signal) which is connected to a triode to turn the LED on or off. You can write high or low, or PWN signals(3.3V or 5V) to S. When you write high to S the LED will turn on and become brightest. When you write low to S the LED will turn off. If you write PWM signals to S the LED's brightness will vary depending on the PWM's signal variances.

2 Features

  • GPIO/PWM interface, 3.3/5V, PWM brightness control
  • Small, easy to be used in various situations
  • 2.54 mm spacing pin
  • PCB Dimension(mm): 8 x 24

LED-01.PCB

  • Pin Description:
Pin Description
S GPIO
V Supply Voltage 5V
G Ground

3 Basic Device Operation

The module has three 2.54 mm spacing pins: V(supply voltage),G(ground) and S(signal) which is connected to a triode to turn the LED on or off. You can write high or low, or PWN signals(3.3V or 5V) to S. When you write high to S the LED will turn on and become brightest. When you write low to S the LED will turn off. If you write PWM signals to S the LED's brightness will vary depending on the PWM's signal variances.

4 Download Matrix Source Code

All the matrix modules' code samples are open source. They are maintained on GitHub - https://github.com/friendlyarm/matrix.git
Each branch in this hub contains the matrix modules' code samples for a board that the matrix modules can work with.

  • The nanopi branch contains the matrix modules' code samples for the NanoPi
  • The nanopi 2 branch contains the matrix modules' code samples for the NanoPi 2
  • The tiny4412 branch contains the matrix modules' code samples for the Tiny4412
  • The raspberrypi branch contains the matrix modules' code samples for the RaspberryPi

Please follow the steps below to get the source code:
Install the git utility on a PC running Ubuntu14.04 

$ sudo apt-get install git

Clone the matrix code from GitHub 

$ git clone https://github.com/friendlyarm/matrix.git

If this is successful a "matrix" directory will be generated, which will contain all the matrix modules' code samples.

5 Connect to NanoPi 2

5.1 Hardware Connection

Please refer to the following connection diagram to connect the Matrix-LED to the NanoPi 2:
Matrix-LED_nanopi_2

Connection Details:

Matrix-LED NanoPi
S Pin7
V Pin4
G Pin6

5.2 Compile Test Program

Please login the matrix hub and enter the nanopi2 branch 

$ cd matrix
$ git checkout nanopi2

Compile the matrix code 

$ make CROSS_COMPILE=arm-linux- clean
$ make CROSS_COMPILE=arm-linux-
$ make CROSS_COMPILE=arm-linux- install

Note: please make sure to install the cross compiler "arm-linux-gcc-4.9.3" on your PC, which is used to compile files for the NanoPi 2.
Generated library files are under the "install/lib" directory. The test program is under the "install/usr/bin" directory.
The modules are under the "modules" directory. The driver's source code is in github: https://github.com/friendlyarm/linux-3.4.y.git

5.3 Run Test Program

Please insert a TF card which is flashed with Debian to a Linux host and mount its boot and rootfs sections.
We assume the rootfs is mounted to /media/rootfs then please run the following commands to copy the module, library and test program to the card.

$ cp modules /media/rootfs/ -r
$ cp install/lib/* /media/rootfs/lib/ -d
$ cp install/usr/bin/* /media/rootfs/usr/bin/

Insert this TF card to your NanoPi 2, power on and run the following command to test.

$ matrix-led

Here is what you expect to observe:
matrix-led_result
You can observe that the LED is flashing.

5.4 Code Sample

int main(int argc, char ** argv) 
{
    int ledPin = GPIO_PIN(7); 
    int i = 0;
    int ret = -1;
 
    if ((ret = exportGPIOPin(ledPin)) == -1) {   
        printf("exportGPIOPin(%d) failed\n", ledPin);
    }
    if ((ret = setGPIODirection(ledPin, GPIO_OUT)) == -1) {
        printf("setGPIODirection(%d) failed\n", ledPin);
    }
 
    for (i = 0; i < LED_BLINK_TIMES; i++) {
        if (i % 2) {
            ret = setGPIOValue(ledPin, GPIO_HIGH);
        } else {
            ret = setGPIOValue(ledPin, GPIO_LOW);
        }
        if (ret == -1) {
            printf("setGPIOValue(%d) failed\n", ledPin);
        }
        printf("LED blinking times %d\n", i);
        sleep(1);
    }
    unexportGPIOPin(ledPin);
    return 0;
}

6 Connect to NanoPi

6.1 Preparations

Please install a Debian on a NanoPi and an appropriate cross compiler on a PC. Please refer to wiki:NanoPi
Compile a NanoPi kernel. Note: please use the kernel's source code from the nanopi-v4.1.y-matrix branch. 

$ git clone https://github.com/friendlyarm/linux-4.x.y.git
$ cd linux-4.x.y
$ git checkout nanopi-v4.1.y-matrix
$ make nanopi_defconfig
$ touch .scmversion
$ make

6.2 Hardware Connection

Please refer to the following connection diagram to connect the Matrix-LED to the NanoPi
matrix-led_nanopi

Connection Details:

Matrix-LED NanoPi
S Pin7
V Pin4
G Pin6

6.3 Compile Test Program

Please login the matrix hub and enter the nanopi branch 

$ cd matrix
$ git checkout nanopi

Compile the matrix code 

$ make CROSS_COMPILE=arm-linux- clean
$ make CROSS_COMPILE=arm-linux-
$ make CROSS_COMPILE=arm-linux- install

Note: please make sure to install the cross compiler "arm-linux-gcc-4.4.3" on your PC, which is used to compile files for the NanoPi-Debian.
Generated library files are under the "install/lib" directory. Applications are under the "install/usr/bin" directory. The test program for the "Matrix-LED" module is "matrix-led".

6.4 Run Test Program

Please copy the library files and test program to the NanoPi 

$ cp install/usr/bin/* nanopi_rootfs/usr/bin/
$ cp install/lib/* nanopi_rootfs/lib/ -d

Power on the NanoPi and run the following command in Debian's terminal 

$ matrix-led

6.5 Code Sample

int main(int argc, char ** argv) 
{
    int ledPin = GPIO_PIN1; 
    int i = 0;
    int ret = -1;
 
    if ((ret = exportGPIOPin(ledPin)) == -1) {   
        printf("exportGPIOPin(%d) failed\n", ledPin);
    }
    if ((ret = setGPIODirection(ledPin, GPIO_OUT)) == -1) {
        printf("setGPIODirection(%d) failed\n", ledPin);
    }
 
    for (i = 0; i < LED_BLINK_TIMES; i++) {
        if (i % 2) {
            ret = setGPIOValue(ledPin, GPIO_HIGH);
        } else {
            ret = setGPIOValue(ledPin, GPIO_LOW);
        }
        if (ret == -1) {
            printf("setGPIOValue(%d) failed\n", ledPin);
        }
        printf("LED blinking times %d\n", i);
        sleep(1);
    }
    unexportGPIOPin(ledPin);
    return 0;
}

7 Connect to Tiny4412

7.1 Preparations

Please refer to the Tiny4412's user's manual to install a UbuntuCore on the Tiny4412 and install an appropriate cross compiler on a PC.
Note: only the Tiny4412SDK-1506 carrier board can work with this module.

7.2 Hardware Connection

Please refer to the following diagram to connect the Matrix-LED to the Tiny4412
matrix-led_tiny4412

Connection Details:

Matrix-LED Tiny4412
S GPIO1 S
V GPIO1 5V
G GPIO1 GND

7.3 Compile Test Program

Please login the Matrix hub and enter the matrix-tiny4412 branch 

$ cd matrix
$ git checkout tiny4412

Compile the matrix code 

$ make CROSS_COMPILE=arm-linux-gnueabihf- clean
$ make CROSS_COMPILE=arm-linux-gnueabihf-
$ make CROSS_COMPILE=arm-linux-gnueabihf- install

Note: please make sure to install the cross compiler "arm-linux-gnueabihf-gcc-4.7.3" on your PC, which is used to compile files for the Tiny4412-UbuntuCore.
Generated library files are under the "install/lib" directory. Applications are under the "install/usr/bin" directory. The test program for the "Matrix-LED" module is "matrix-led".

7.4 Run Test Program

Please copy the library files and test program to the Tiny4412 

$ cp install/usr/bin/* tiny4412_rootfs/usr/bin/
$ cp install/lib/* tiny4412_rootfs/lib/ -d

Power on the Tiny4412 and run the following command in UbuntuCore's terminal 

$ matrix-led

7.5 Code Sample

int main(int argc, char ** argv) 
{
    int ledPin = GPIO_PIN1; 
    int i = 0;
    int ret = -1;
 
    if ((ret = exportGPIOPin(ledPin)) == -1) {   
        printf("exportGPIOPin(%d) failed\n", ledPin);
    }
    if ((ret = setGPIODirection(ledPin, GPIO_OUT)) == -1) {
        printf("setGPIODirection(%d) failed\n", ledPin);
    }
 
    for (i = 0; i < LED_BLINK_TIMES; i++) {
        if (i % 2) {
            ret = setGPIOValue(ledPin, GPIO_HIGH);
        } else {
            ret = setGPIOValue(ledPin, GPIO_LOW);
        }
        if (ret == -1) {
            printf("setGPIOValue(%d) failed\n", ledPin);
        }
        printf("LED blinking times %d\n", i);
        sleep(1);
    }
    unexportGPIOPin(ledPin);
    return 0;
}

8 Connect to RaspberryPi

9 Connect to Arduino

10 Resources

11 Update Log

11.1 Feb-18-2016

  • Added the description for "NanoPi 2 branch" in Section 4
  • Added Section 5: Connect to NanoPi 2


Retrieved from "https://wiki.friendlyelec.com/wiki/index.php?title=Matrix_-_LED&oldid=3778"