NanoPi R6S

1 Introduction

Overview

Front

Back

• The NanoPi R6S is a RK3588S SoC based ARM board.

2 Hardware Spec

• SoC: Rockchip RK3588S
  • CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
  • GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
  • VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265 encoder
  • NPU: 6TOPs, supports INT4/INT8/INT16/FP16
• RAM: 64-bit 8GB LPDDR4X at 2133MHz
• Flash: 32GB eMMC, at HS400 mode
• Ethernet: one Native Gigabit Ethernet, and two PCIe 2.5G Ethernet
• USB: one USB 3.0 Type-A and one USB 2.0 Type-A
• HDMI:
  • compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
  • support up to 7680x4320@60Hz
  • Support RGB/YUV(up to 10bit) format
• microSD: support up to SDR104 mode
• GPIO:
  • 12-pin 0.5mm FPC connector
  • with up to 1x SPI, up to 3x UARTs, up to 1x I2Cs, up to 8x GPIOs
• Debug: one Debug UART, 3 Pin 2.54mm header, 3.3V level, 1500000bps
• LEDs: 4 x GPIO Controlled LED (SYS, WAN, LAN1, LAN2)
• others:
  • 2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS
  • one IR receiver and the carrier frequency is 38Khz
  • MASK button for eMMC update
  • one user button
  • one 5V Fan connector
• Power supply: USB-C, support PD, 5V/9V/12V/20V input
• PCB: 8 Layer, 62x90x1.6mm
• Ambient Operating Temperature: 0℃ to 70℃

3 Diagram, Layout and Dimension

3.1 Layout

NanoPi R6S Layout

• 12-pin GPIO

Pin#	GPIO	SPI	UART	I2C	POWER	Description
1					VCC3V3_SYS_S3	3.3V power output
2					VCC3V3_SYS_S3	3.3V power output
3	GPIO1_B3	SPI0_CLK_M2	UART4_TX_M2			3.3V level
4					GND
5	GPIO1_B1	SPI0_MISO_M2				3.3V level
6	GPIO1_B4	SPI0_CS0_M2				3.3V level
7	GPIO1_B2	SPI0_MOSI_M2	UART4_RX_M2			3.3V level
8					GND
9	GPIO1_B7		UART1_RX_M1	I2C5_SDA_M3		3.3V level
10	GPIO1_B6		UART1_TX_M1	I2C5_SCL_M3		3.3V level
11	GPIO3_C4		UART5_TX_M1			3.3V level
12	GPIO3_C5		UART5_RX_M1			3.3V level

• Debug UART Pin Spec

3.3V level signals, 1500000bps

Pin#	Assignment	Description
1	GND	0V
2	UART2_TX_M0_DEBUG	output
3	UART2_RX_M0_DEBUG	intput

• USB Port

Each USB Type-A port has 1.4A overcurrent protection.

• RTC

RTC backup current is 0.25μA TYP (VDD =3.0V, TA =25℃).

Connector P/N: Molex 53398-0271

• IR receiver

Connected to PWM3_IR_M0

38Khz carrier frequency

compatible with NEC protocol, User code is 3B4C

Support power on via IR controller

Support FriendlyELEC RC100 IR controller

6 Schematic, PCB CAD File

• Schematic: NanoPi_R6S_2208_SCH.PDF
• PCB CAD File：[]