NanoPC-T3 Plus

From FriendlyELEC WiKi
Revision as of 09:00, 21 November 2017 by Yonganch (Talk | contribs) (Hardware Spec)

Jump to: navigation, search

查看中文

1 Introduction

Overview
Front
Back
  • The NanoPC-T3(2GB) octa-core single board computer is designed and developed by FriendlyELEC for professional and enterprise users. It uses the Samsung Octa-Core Cortex-A53 S5P6818 SoC. Compared to the FriendlyELEC NanoPC-T2 the NanoPC-T3(2GB) not only has all the T2’s interfaces and ports but also has a more powerful SoC. Its dynamic frequency scales from 400M up to 1.4GHz. The NanoPC-T3(2GB) has 16G eMMC onboard, audio jack, video input/output interfaces, built-in WiFi, Bluetooth and Gbps Ethernet port. In addition the NanoPC-T3(2GB) has power management, on board porcelain antenna and serial debug port. To avoid overheat issues the NanoPC-T3(2GB) has a heat sink with mounting holes.
  • The NanoPC-T3(2GB) has two camera interfaces: a DVP camera interface and a MIPI-CSI interface, and four video interfaces: HDMI 1.4A, LVDS, parallel RGB-LCD interface and MIPI-DSI interface. It supports RTC and has RTC interface pins. It has four USB ports with three being type A ports and one being 2.54mm pitch pin-headers.
  • The NanoPC-T3(2GB) supports muitple OS systems e.g. Android5.1, Debian and UbuntoCore+Qt. It is an open source project with rich interfaces and ports. It is born a choice for professional and enterprise users.

2 Hardware Spec

  • SoC: Samsung S5P6818 Octa-Core Cortex-A53, 400M Hz - 1.4G Hz
  • PMU Power Management: Implemented by a Cortex-M0 MCU, support software power-off, sleep and wakeup functions
  • System Memory: 2GB 32bit DDR3 RAM
  • SD Storage: 1 x microSD Card Socket
  • Ethernet: Gbit Ethernet(RTL8211E)
  • WiFi: 802.11b/g/n
  • Bluetooth: 4.0 dual mode
  • Antenna: Porcelain Antenna IPX Interface
  • eMMC: 16GB
  • Video Input: DVP Camera/MIPI-CSI (two camera interfaces)
  • Video Output: HDMI Type-A / LVDS / Parallel RGB-LCD / MIPI-DSI (four video output interfaces)
  • Audio: 3.5 mm audio jack / via HDMI
  • Microphone: onboard Microphone
  • USB Host: 4 x USB 2.0 Host, three type A ports and one 2.54 mm pitch pin-headers
  • MicroUSB: 1 x MicroUSB 2.0 Client, Type A
  • LCD Interface: 0.5mm pitch 45 pin FPC seat, full color RGB 8-8-8
  • HDMI: 1.4A Type A, 1080P
  • DVP Camera: 0.5mm pitch 24 pin FPC seat
  • GPIO: 2.54 mm pitch 30 pin-header
  • I2S/USB: 2.54 mm pitch 14 pin-header
  • Serial Debug Port: 2.54mm pitch 4-pin-header
  • User Key: power, Reset, boot selection
  • LED: 1 x power LED and 1 x system LED
  • Other Resources: CPU’s internal TMU
  • RTC Battery: RTC Battery Seat
  • Heat Sink: 1 x Heat Sink with mounting holes
  • Power: DC 5V/3A
  • PCB: Six Layer
  • Dimension: 100 mm x 64 mm
  • Working Temperature: -40℃ to 80℃
  • OS/Software: uboot, Android and Debian

3 Diagram, Layout and Dimension

3.1 Layout

NanoPC-T3(2GB) Layout
  • 30Pin GPIO Pin Spec
Pin# Name Pin# Name
1 SYS_3.3V 2 DGND
3 UART2_TX/GPIOD20 4 UART2_RX/GPIOD16
5 I2C0_SCL 6 I2C0_SDA
7 SPI0_MOSI/GPIOC31 8 SPI0_MISO/GPIOD0
9 SPI0_CLK/GPIOC29 10 SPI0_CS/GPIOC30
11 UART3_TX/GPIOD21 12 UART3_RX/GPIOD17
13 UART4_TX/GPIOB29 14 UART4_RX/GPIOB28
15 UART5_TX/GPIOB31 16 UART5_RX/GPIOB30
17 GPIOC4 18 GPIOC7
19 GPIOC8 20 GPIOC24
21 GPIOC28 22 GPIOB26
23 GPIOD1/PWM0 24 GPIOD8/PPM
25 GPIOC13/PWM1 26 AliveGPIO3
27 GPIOC14/PWM2 28 AliveGPIO5
29 VDD_5V 30 DGND
  • 14Pin I2S/USB Pin Spec
Pin# Name Pin# Name
1 5V 2 5V
3 USB_DM2 4 LED1
5 USB_DP2 6 I2S_SDIN1
7 DGND 8 I2S_SDOUT1
9 PWRKEY 10 I2S_MCLK1
11 NRESETIN 12 I2S_BCLK1
13 DGND 14 I2S_LRCK1
  • DVP Camera Interface Pin Spec
Pin# Name
1, 2 SYS_3.3V
7,9,13,15,24 DGND
3 I2C0_SCL
4 I2C0_SDA
5 GPIOB14
6 GPIOB16
8 GPIOC13/PWM1
10 NC
11 VSYNC
12 HREF
14 PCLK
16-23 Data bit7-0
  • LVDS
Pin# Name
1 VDD_5V
2 VDD_5V
3 VDD_5V
4 LVDS_Y0M
5 LVDS_Y0P
6 DGND
7 LVDS_Y1M
8 LVDS_Y1P
9 DGND
10 LVDS_Y2M
11 LVDS_Y2P
12 DGND
13 LVDS_CLKM
14 LVDS_CLKP
15 DGND
16 LVDS_Y3M
17 LVDS_Y3P
18 DGND
19 GPIOC15
20 DGND
21 I2C2_SCL
22 I2C2_SDA
23 GPIOC16
24 DGND
  • Debug Port(UART0)
Pin# Name
1 DGND
2 VDD_5V
3 UART_TXD0
4 UART_RXD0
  • RGB LCD Interface Pin Spec
Pin# Name Description
1, 2 VDD_5V 5V Output, it can be used to power LCD modules
11,20,29, 37,38,39,40, 45 DGND Ground
3-10 Blue LSB to MSB RGB blue
12-19 Green LSB to MSB RGB green
21-28 Red LSB to MSB RGB red
30 GPIOB25 available for users
31 GPIOC15 occupied by FriendlyARM one wire technology to recognize LCD models and control backlight and implement resistive touch, not applicable for users
32 XnRSTOUT Form CPU low when system is reset
33 VDEN signal the external LCD that data is valid on the data bus
34 VSYNC vertical synchronization
35 HSYNC horizontal synchronization
36 LCDCLK LCD clock, Pixel frequency
41 I2C2_SCL I2C2 clock signal, for capacitive touch data transmission
42 I2C2_SDA I2C2 data signal, for capacitive touch data transmission
43 GPIOC16 interrupt pin for capacitive touch, used with I2C2
44 NC Not connected
  • MIPI-DSI Interface Pin Spec
Pin# Name
1, 2, 3 VDD_5V
4 DGND
5 I2C2_SDA
6 I2C2_SCL
7 DGND
8 GPIOC16
9 DGND
10 GPIOC1
11 DGND
12 NC
13 nRESETOUT
14, 15 DGND
16 MIPIDSI_DN3
17 MIPIDSI_DP3
18 DGND
19 MIPIDSI_DN2
20 MIPIDSI_DP2
21 DGND
22 MIPIDSI_DN1
23 MIPIDSI_DP1
24 DGND
25 MIPIDSI_DN0
26 MIPIDSI_DP0
27 DGND
28 MIPIDSI_DNCLK
29 MIPIDSI_DPCLK
30 DGND
  • MIPI-CSI Interface Pin Spec
Pin# Name
1, 2 SYS_3.3V
3 DGND
4 I2C0_SDA
5 I2C0_SCL
6 DGND
7 SPI2_MOSI/GPIOC12
8 SPI2_MISO/GPIOC11
9 SPI2_CS/GPIOC10
10 SPI2_CLK/GPIOC9
11 DGND
12 GPIOB23
13 GPIOC2
14, 15 DGND
16 MIPICSI_DN3
17 MIPICSI_DP3
18 DGND
19 MIPICSI_DN2
20 MIPICSI_DP2
21 DGND
22 MIPICSI_DN1
23 MIPICSI_DP1
24 DGND
25 MIPICSI_DN0
26 MIPICSI_DP0
27 DGND
28 MIPICSI_DNCLK
29 MIPICSI_DPCLK
30 DGND
  • RTC
3.35uA@3V
  • USB 2.0 Host
with 1A over current protection
Notes
  1. SYS_3.3V: 3.3V power output
  2. VDD_5V: 5V power output
  3. For more details refer to the document: NanoPC-T3-1709-Schematic.pdf

3.2 Board Dimension

NanoPC-T3 Dimensions

For more details refer to the document: NanoPC-T3-1709-Drawing(dxf).zip
  • Power Jack
  • DC 4.7~5.6V IN, 4.0*1.7mm Power Jack
DC-023.png