NanoPi A64

查看中文

1 Introduction

The NanoPi A64 is a new board of high performance with low cost designed by FriendlyElec. It uses Allwinner’s A64 quad-core SoC(ARM Cortex-A53). FriendlyElec has made a UbuntuCore and a UbuntuMATE image files for it.

The NanoPi A64 is a small board with comprehensive interfaces, ports and features. It has Ethernet, IR receiver, Video/Audio input and output. It has onboard AXP803 PMU and WiFi. It takes power input from its MicroUSB port. It has MIPI-DSI and DVP interfaces, GPIO pin-header compatible with Raspberry Pi and a serial debug port.

2 Hardware Spec

• CPU: Allwinner A64, Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
• GPU: Mali400MP2, Supports OpenGL ES2.0, OpenVG1.1
• DDR3 RAM: 1GB
• Ethernet: One Gigabit Ethernet (RTL8211E)
• PMU Power Management: AXP803, support software power-off
• Wi-Fi: 802.11b/g/n
• Audio Out/MIC: 3.5mm audio jack
• IR Receiver: Onboard IR receiver
• USB 2.0 Type A x 2
• Serial Debug Port: 2.54mm pitch 4pin-header
• microSD Slot x 1
• microUSB x 1: only for power input
• DVP Camera: 0.5mm pitch 24pin FPC seat
• Video Out: 1.4 HDMI Type-A
• MIPI DSI: 0.5mm pitch 30pin FPC seat
• GPIO: 2.54mm pitch 40pin-header, compatible with Raspberry Pi's GPIO. It includes UART, SPI, I2C, PWM, IO etc
• I2S: 7pin, 2.54mm pitch
• Power Button x 1
• LED: Power Indication x 1, System LED x 1
• PCB : Six layer, ENIG
• Dimension: 64 x 60mm
• Power: DC 5V/2A
• OS: Ubuntu-Core with QtE, Ubuntu-MATE

3 Diagram, Layout and Dimension

3.1 Layout

NanoPi A64接口布局

• GPIO Pin Description

Pin#	Name	Pin#	Name
1	SYS_3.3V	2	VDD_5V
3	GPIOE15/I2C2_SDA	4	VDD_5V
5	GPIOE14/I2C2_SCL	6	GND
7	GPIOD7	8	GPIOH4/UART3-TX
9	GND	10	GPIOH5/UART3-RX
11	GPIOB0/UART2-TX	12	GPIOL10/PWM_S
13	GPIOL8/I2C_S_SCL	14	GND
15	GPIOL9/I2C_S_SDA	16	GPIOH6/UART3-RTS
17	SYS_3.3V	18	GPIOH7/UART3-CTS
19	GPIOC0/SPI0-MOSI	20	GND
21	GPIOC1/SPI0-MISO	22	GPIOB1/UART2-RX
23	GPIOC2/SPI0-CLK	24	GPIOC3/SPI0-CS
25	GND	26	GPIOH8/SPDIF-OUT
27	GPIOH3/I2C1_SDA	28	GPIOH2/I2C1_SCL
29	GOIOH10	30	GND
31	GOIOH11	32	GPIOD4
33	GPIOD5	34	GND
35	GPIOD3/SPI1-MISO	36	GPIOD0/SPI1-CS
37	GPIOD6	38	GPIOD2/SPI1-MOSI
39	GND	40	GPIOD1/SPI1-CLK

• Debug Port（UART0）

Pin#	Name
1	GND
2	VDD_5V
3	UART0-TX
4	UART0-RX

• I2S/PCM Pin Description

Pin#	Name
1	GND
2	SYS_3.3V
3	GPIOB5/PCM0-BCLK
4	GPIOB4/PCM0-SYNC
5	GPIOB6/PCM0-DOUT
6	GPIOB7/PCM0-DIN
7	GPIOB3/I2S0-MCLK

• DVP Camera IF Pin Description

Pin#	Name	Description
1, 2	SYS_3.3V	3V电源输出给外部摄像头模块
7,9,13,15,24	GND	参考地, 0V
3	CAM_SCL	I2C时钟信号
4	CAM_SDA	I2C数据信号
5	GPIOE17	普通GPIO, 施加给外部摄像头模块的控制信号
6	GPIOE16	普通GPIO, 施加给外部摄像头模块的控制信号
8	MCLK	提供给外部摄像头模块的时钟信号
10	NC	没有连接
11	VSYNC	外部摄像头模块输出给CPU的行信号
12	HREF/HSYNC	外部摄像头模块输出给CPU的场信号
14	PCLK	外部摄像头模块输出给CPU的像数点信号
16-23	Data bit7-0	数据信号

• MIPI-DSI Pin Description

Pin#	Name	Description
1, 2, 3	VDD_5V	5V电源输出给外部供电
4,7,9,11,14,15,18,21,24,27,30	GND	参考地, 0V
5	I2C0_SDA	I2C时钟信号
6	I2C0_SCL	I2C数据信号
8	GPIOL7	普通GPIO
10	GPIOB2	普通GPIO
12	GPIOL12	普通GPIO
13	AP-RESET#	系统复位输出
16	MIPI-DSI-D3N	MIPI DSI数据, 差分信号负
17	MIPI-DSI-D3P	MIPI DSI数据, 差分信号正
19	MIPI-DSI-D2N	MIPI DSI数据, 差分信号负
20	MIPI-DSI-D2P	MIPI DSI数据, 差分信号正
22	MIPI-DSI-D1N	MIPI DSI数据, 差分信号负
23	MIPI-DSI-D1P	MIPI DSI数据, 差分信号正
25	MIPI-DSI-D0N	MIPI DSI数据, 差分信号负
26	MIPI-DSI-D0P	MIPI DSI数据, 差分信号正
28	MIPI-DSI-CKN	MIPI DSI时钟, 差分信号负
29	MIPI-DSI-CKP	MIPI DSI时钟, 差分信号正

说明

1. SYS_3.3V: 电源输出, 实际输出为3.1V
2. VDD_5V: 5V电源输入/输出。输入范围：4.7～5.6V, 可通过MicroUSB接口供电, 也可通过40pin排针或Debug Port上的VDD_5V供电. VDD_5V与MicroUSB的VBUS直接相连.
3. 全部信号引脚均为3.3V电平(实际是3.1V, 兼容3.3V)，输出电流为5mA,可以带动小负荷模块，io都不能带负载
4. 更详细的信息请查看原理图

3.2 Dimensional Diagram

详细尺寸：dxf文件