Matrix - Button

查看中文

1 Introduction

Button

• The Matrix-Button module is used to detect button events.
• If the button is not pressed S will output high otherwise S will output low.

2 Features

• 3 PIN interface
• PCB dimension (mm): 8 x 24

• Pin Description:

Pin	Description
S	GPIO
V	Supply Voltage 5V
G	Ground

3 Basic Device Operation

• The Matrix-Button is an instant(non self-lock) button. The button's status can be read from pin S in the 3-pin 2.54 mm spacing pin header.
• If the button is not pressed S will output high otherwise S will output low.

4 Applications

4.1 Connect to NanoPi M1

Please refer to the following connection diagram to connect the module to the NanoPi M1:

Connection Details:

Matrix-Button	NanoPi M1
S	Pin7
V	Pin4
G	Pin6

4.2 Connect to NanoPi 2

Please refer to the following connection diagram to connect the module to the NanoPi 2:

Connection Details:

Matrix-Button	NanoPi 2
S	Pin7
V	Pin4
G	Pin6

4.3 Connect to NanoPi M2 / NanoPi 2 Fire

Please refer to the following connection diagram to connect the module to the NanoPi M2/ NanoPi 2 Fire:

Connection Details:

Matrix-Button	NanoPi M2
S	Pin7
V	Pin4
G	Pin6

4.4 Connect to NanoPC-T2

Please refer to the following connection diagram to connect the module to the NanoPC-T2:
Matrix-Button_NanoPC-T2

Connection Details:

Matrix-Button	NanoPC-T2
S	Pin15
V	Pin29
G	Pin30

5 Compile & Run Test Program

Boot your ARM board with Debian and copy the matrix code:

$ apt-get update && apt-get install git
$ git clone https://github.com/friendlyarm/matrix.git

If your cloning is done successfully a "matrix" directory will be generated.

Compile and install Matrix:

$ cd matrix
$ make && make install

Run test program:

$ matrix-gpio_int

Note: this module is not plug and play therefore before running the module please make sure it is connected to an ARM board.
Here is what you should observe:

Waiting event...
Device[0] value is 1

When you press the button an event will be detected.

6 Code Sample

This Matrix code sample can work with all the ARM boards mentioned in this module's wiki. The name of this code sample is "matrix-gpio_int". Here is its source code:

int main(int argc, char ** argv)
{
    int i, board;
    int retSize = -1;
    char value[ARRAY_SIZE(dev)];
 
    if ((board = boardInit()) < 0)
        printf("Fail to init board\n");
 
    if (argc == 2) {
        dev[0].pin = atoi(argv[1]);
    }
    printf("Using GPIO_PIN(%d)\n", dev[0].pin);
    system("modprobe "DRIVER_MODULE);
    signal(SIGINT, intHandler);
    if (board == BOARD_NANOPI_T2)
        dev[0].pin = GPIO_PIN(15);
    if ((devFD =sensorInit(dev, ARRAY_SIZE(dev))) == -1) {
        printf("Fail to init sensor\n");
        return -1;
    }
    printf("Waiting event...\n");
    if ((retSize = sensorRead(devFD, value, ARRAY_SIZE(dev))) == -1) {
        printf("Fail to read sensors\n");
    }
    if (retSize > 0) {
        i = 0;
        for (i=0; i<retSize; i++) {
            printf("dev[%d] value: %d\n", i, value[i]);
        }
    }
    sensorDeinit(devFD);
    system("rmmod "DRIVER_MODULE);
    return 0;
}

For more details about this APIs called in this code sample refer to Matrix API reference manual

8 Update Log

8.1 Feb-19-2016

• In section 4 added NanoPi 2 branch
• In section 5.2 added the driver and its source code's locations

8.2 June-17-2016

• Re-organized and simplified wiki