Matrix - I2C LCD1602

From FriendlyELEC WiKi
Revision as of 09:04, 23 February 2016 by Yftan (Talk | contribs) (→‎编译测试程序)

Jump to: navigation, search

查看中文

1 Introduction

I2C LCD1602
I2C LCD1602
  • The Matrix-I2C_LCD1602 is an LCD display module composed of an LCD1602 and a PCF8574 module.
  • The LCD1602 can display up to 16x2 characters. It has a parallel interface.
  • The PCF8574 provides GPIO expansion up to 8 bit for I2C. It communicates with a master via I2C and converts data from the master to parallel signals to the LCD1602 thus controls the LCD's display and back light.

2 Features

  • I2C interface, LCD display and backlight control
  • 2.54mm spacing pin
  • IIC Module PCB dimension(mm): 16 x 42
  • LCD1602 PCB dimension (mm): 36 x 80

IIC模块PCB LCD1602 PCB

  • Pin Description:
Pin Description
SDA I2C SDA
SCL I2C SCL
5V Supply Voltage 5V
GND Ground

3 Basic Device Operation

3.1 PCF8574

  • The PCF8574 has I2C parallel expansion. It has an 8bit (P0 - P7) I2C interface.
  • The PCF8574 communicates with a master via I2C. The PCF8574's chip model is PCF8574T whose address specification is as follows:

PCF8574

  • If A2 - A0 are all set to 1 the 7bit address will be 0x27(0100111). By default RW is 0 and it is in the write mode.
  • In the write mode after opening the i2c-0 device and setting up its address the master can write data to it.
  • If you need to read data from it you will need to set the module to the read mode (RW set to 1). Please refer to the PCF8574's datasheet for more details.

3.2 LCD1602

  • The connection diagram between the PCF8574 module and the LCD module is as follows:

1602

  • RS is instruction/data register selection. RW is read/write selection. E is enable signal(edge triggering). BL is back light control. D4-D7 are data bits.
  • The LCD module is controlled by four data bits through which we can send instructions to control its state. Because it has eight instruction/data bits (DB7 - DB0) when writing each instruction/data we need to write the most significant four bits DB7 - DB4 first and then the least significant four bits DB3 - DB0.
  • Note: the LCD module has 192 most commonly used characters stored in CGROM. When we write a common character e.g "A" it will directly display "A". In addition it can store up to eight user defined characters in RAM called CGRAM.

4 Download Matrix Source Code

All the matrix modules' code samples are open source. They are maintained on GitHub - https://github.com/friendlyarm/matrix.git
Each branch in this hub contains the matrix modules' code samples for a board that the matrix modules can work with.

  • The nanopi branch contains the matrix modules' code samples for the NanoPi
  • The nanopi 2 branch contains the matrix modules' code samples for the NanoPi 2
  • The tiny4412 branch contains the matrix modules' code samples for the Tiny4412
  • The raspberrypi branch contains the matrix modules' code samples for the RaspberryPi

Install the git utility on a PC running Ubuntu14.04 

$ sudo apt-get install git

Clone the matrix code from GitHub 

$ git clone https://github.com/friendlyarm/matrix.git

If this is successful a "matrix" directory will be generated, which will contain all the matrix modules' code samples.

5 Connect to NanoPi 2

5.1 Hardware Connection

Please refer to the following connection diagram to connect the Matrix-I2C_LCD1602 to the NanoPi 2:
Matrix-I2C_LCD1602_nanopi_2

Connection Details:

Matrix-I2C_LCD1602 NanoPi
SDA Pin3
SCL Pin5
5V Pin4
GND Pin6

5.2 Compile Test Program

Please login the matrix hub and enter the nanopi2 branch 

$ cd matrix
$ git checkout nanopi2

Compile the matrix code 

$ make CROSS_COMPILE=arm-linux- clean
$ make CROSS_COMPILE=arm-linux-
$ make CROSS_COMPILE=arm-linux- install

Note: please make sure to install the cross compiler "arm-linux-gcc-4.9.3" on your PC, which is used to compile files for the NanoPi 2.
Generated library files are under the "install/lib" directory. The test program is under the "install/usr/bin" directory.
The modules are under the "modules" directory. The driver's source code is in github: https://github.com/friendlyarm/linux-3.4.y.git

5.3 运行测试程序

将带有Debian系统的SD卡插入一台运行Linux的电脑，可以挂载SD卡上的boot和rootfs分区。
假设rootfs分区的挂载路径为/media/rootfs，执行以下命令将Matrix的硬件驱动、库文件和测试程序拷贝到NanoPi 2的文件系统上。

$ cp modules /media/rootfs/ -r
$ cp install/lib/* /media/rootfs/lib/ -d
$ cp install/usr/bin/* /media/rootfs/usr/bin/

将SD卡重新插入NanoPi 2，上电启动，在Debian的shell终端中执行以下命令运行模块Matrix-I2C_LCD1602的测试程序。

$ matrix-lcd1602

注意：此模块并不支持热插拔，启动系统前需要确保硬件连接正确。
运行效果如下：
matrix-lcd1602_result
LCD上会显示下列2行字符：
" B&G Char LCD"
"--by FriendlyARM"

5.4 Code Sample

int main(int argc, char ** argv)
{
    int devFD;
    if ((devFD = LCD1602Init()) == -1) {
        printf("Fail to init LCD1602\n");
        return -1;
    }
 
    if (LCD1602Clear(devFD) == -1) {
        printf("Fail to Clear\n");
        return -1;
    }
    printf("clearing LCD1602\n");
    sleep(1);
 
    if (LCD1602DispLines(devFD, "  B&G Char LCD", "--by FriendlyARM") == -1) {
        printf("Fail to Display String\n");
        return -1;
    }
    printf("displaying LCD1602\n");
    LCD1602DeInit(devFD);
    return 0;
}


6 Connect to NanoPi

6.1 Preparations

Please install a Debian on a NanoPi and an appropriate cross compiler on a PC. Please refer to wiki:NanoPi
Compile a NanoPi kernel. Note: please use the kernel's source code from the nanopi-v4.1.y-matrix branch.

$ git clone https://github.com/friendlyarm/linux-4.x.y.git
$ cd linux-4.x.y
$ git checkout nanopi-v4.1.y-matrix
$ make nanopi_defconfig
$ touch .scmversion
$ make

6.2 Hardware Connection

Please refer to the following connection diagram to connect the Matrix-I2C_LCD1602 to the NanoPi
matrix-i2c_lcd1602_nanopi

Connection Details:

Matrix-I2C_LCD1602 NanoPi
SDA Pin3
SCL Pin5
5V Pin4
GND Pin6

6.3 Compile Test Program

Please login the matrix hub and enter the nanopi branch 

$ cd matrix
$ git checkout nanopi

Compile the matrix code 

$ make CROSS_COMPILE=arm-linux- clean
$ make CROSS_COMPILE=arm-linux-
$ make CROSS_COMPILE=arm-linux- install

Note: please make sure to install the cross compiler "arm-linux-gcc-4.4.3" on your PC, which is used to compile files for the NanoPi-Debian.
Generated library files are under the "install/lib" directory. Applications are under the "install/usr/bin" directory. The test program for the "Matrix-I2C_LCD1602" module is "matrix-lcd1602".

6.4 Run Test Program

Please copy the library files and test program to the NanoPi 

$ cp install/usr/bin/* nanopi_rootfs/usr/bin/
$ cp install/lib/* nanopi_rootfs/lib/ -d

Power on the NanoPi and run the following command in Debian's terminal
Note: this module is not plug and play therefore before running the module please make sure it is connected to a NanoPi. 

$ matrix-lcd1602

6.5 Code Sample

int main(int argc, char ** argv)
{
    int devFD;
    if ((devFD = LCD1602Init()) == -1) {
        printf("Fail to init LCD1602\n");
        return -1;
    }
 
    if (LCD1602Clear(devFD) == -1) {
        printf("Fail to Clear\n");
        return -1;
    }
    printf("clearing LCD1602\n");
    sleep(1);
 
    if (LCD1602DispLines(devFD, "  B&G Char LCD", "--by FriendlyARM") == -1) {
        printf("Fail to Display String\n");
        return -1;
    }
    printf("displaying LCD1602\n");
    LCD1602DeInit(devFD);
    return 0;
}

7 Connect to Tiny4412

7.1 Preparations

Please refer to the Tiny4412's user's manual to install a UbuntuCore on the Tiny4412 and install an appropriate cross compiler on a PC.
Note: only the Tiny4412SDK-1506 carrier board can work with this module.

7.2 Hardware Connection

Please refer to the following diagram to connect the Matrix-I2C_LCD1602 to the Tiny4412
matrix-i2c_lcd1602_tiny4412

Connection Details:

Matrix-I2C_LCD1602 Tiny4412
SDA CON18 SDA
SCL CON18 SCL
5V CON18 5V
GND CON18 GND

7.3 Compile Test Program

Please login the Matrix hub and enter the matrix-tiny4412 branch 

$ cd matrix
$ git checkout tiny4412

Compile the Matrix code 

$ make CROSS_COMPILE=arm-linux-gnueabihf- clean
$ make CROSS_COMPILE=arm-linux-gnueabihf-
$ make CROSS_COMPILE=arm-linux-gnueabihf- install

Note: please make sure to install the cross compiler "arm-linux-gnueabihf-gcc-4.7.3" on your PC, which is used to compile files for the Tiny4412-UbuntuCore.
Generated library files are under the "install/lib" directory. Applications are under the "install/usr/bin" directory. The test program for the "Matrix-I2C_LCD1602" module is "matrix-lcd1602".

7.4 Run Test Program

Please copy the library files and test program to the Tiny4412 

$ cp install/usr/bin/* tiny4412_rootfs/usr/bin/
$ cp install/lib/* tiny4412_rootfs/lib/ -d

Power on the Tiny4412 and run the following command in UbuntuCore's terminal
Note: this module is not plug and play therefore before running the module please make sure it is connected to a Tiny4412. 

$ matrix-lcd1602

7.5 Code Sample

int main(int argc, char ** argv)
{
    int devFD;
    if ((devFD = LCD1602Init()) == -1) {
        printf("Fail to init LCD1602\n");
        return -1;
    }
 
    if (LCD1602Clear(devFD) == -1) {
        printf("Fail to Clear\n");
        return -1;
    }
    printf("clearing LCD1602\n");
    sleep(1);
 
    if (LCD1602DispLines(devFD, "  B&G Char LCD", "--by FriendlyARM") == -1) {
        printf("Fail to Display String\n");
        return -1;
    }
    printf("displaying LCD1602\n");
    LCD1602DeInit(devFD);
    return 0;
}

8 Connect to RaspberryPi

9 Connect to Arduino

9.1 Preparations

Make sure your Arduino board can work. Here is a reference link - https://www.arduino.cc/en/Guide/HomePage
Here we tried the Arduino Uno

9.2 Hardware Connection

Please refer to the following diagram to connect the Matrix-I2C_LCD1602 to the Arduino Uno
matrix-i2c_lcd1602_arduino

9.3 Compile & Run Test Program

All the matrix modules' code samples for Arduino are maintained on GitHub - https://github.com/friendlyarm/matrix-arduino.git
Clone the matrix code from GitHub 

$ git clone https://github.com/friendlyarm/matrix-arduino.git

If this is successful a "matrix-arduino" directory will be generated, which will contain all the matrix modules' code samples.

Please copy the entire directory "matrix-i2c_lcd1602" to "Arduino_IDE/libraries" 

$ cd matrix-arduino
$ cp matrix-i2c_lcd1602 Arduino_IDE/libraies -r

Start Arduino IDE
Click on File->Examples->matrix-i2c_lcd1602->displaychar and run the test program.
Click on upload and run the test program.

9.4 Code Sample

#include <Wire.h> 
#include <LiquidCrystal_I2C.h>
 
// set the LCD address to 0x27 for a 16 chars and 2 line display
LiquidCrystal_I2C lcd(0x27,16,2);  
 
void setup()
{
  lcd.init();                        
  lcd.backlight();
  lcd.setCursor(2, 0);
  lcd.print("B&G Char LCD"); 
  lcd.setCursor(0, 1);
  lcd.println("--by FriendlyARM");
}
 
void loop()
{
}

10 Resources

LCD1602.pdf
pcf8574.pdf


11 Update Log

11.1 Feb-23-2016

  • Added the description for "NanoPi 2 branch" in Section 4
  • Added Section 5: Connect to NanoPi 2


Retrieved from "https://wiki.friendlyelec.com/wiki/index.php?title=Matrix_-_I2C_LCD1602&oldid=3801"