APITestPage/zh

1 如何使用SDIO WiFi

1.1 AP模式

• FriendlyWrt系统的无线功能默认是关闭状态, 要启用WiFi, 可点击“网络>无线”进入配置无线WiFi界面, 找到“无线未启用”那一行, 点击后面的“启用”按钮即可
  
• 启用后, 在手机上搜索连接名称类拟 FriendlyWrt-xx:yy:zz 名称的WiFi热点, 输入默认密码password即可连接
  
• {{{1}}}支持的SDIO WiFi型号为: rtl8822cs
  

1.2 无线中继模式

• 连接到主无线路由器

点击 "网络" -> "无线", 在界面上点击 "Generic MAC80211 802.11ac/b/g/n" 后面的 "扫描" 按钮扫描网络，点击无线路由器后面的 "加入网络" 按钮，
在加入网络的配置页面中，勾选 "重置无线配置"，在 "WPA密钥"一栏中输入密钥，其他配置保持默认，点 "提交"，再点击 "保存"，
最后点 "保存并应用", 连接成功后，可以在FriendlyWrt首页看到IP地址。

• 创建无线热点

点击 "网络" -> "无线"，在界面上点击 "Generic MAC80211 802.11ac/b/g/n" 后面的 "添加" 按钮，将会弹出 "编辑无线网络" 页面，
在 "工作频率" 一栏中设置无线信道（例如"40 (5200 MHz)")，
在 "ESSID" 一栏中，输入热点名称，
在 "网络" 一栏中，钩选 "lan"，
点击 "无线安全", 设置加密类型，然后点击 "保存", 然后点击 "保存并应用"，
由于需要重启才能生效，点击 "系统" 选择 "重启"。

2 How to use SDIO WiFi

2.1 AP Mode

• FriendlyWrt's wireless function is disabled by default, to enable WiFi, you can click "Network > Wireless", and then click the "Enable" button.
  
• Search for a WiFi hotspot with a name like FriendlyWrt-xx:yy:zz on your phone, enter the default password "password" to connect.
  
• SDIO WiFi models supported: rtl8822cs
  

2.2 Wireless Repeater Mode

• Connect to the wireless router

Click "Network" -> "Wireless", Click the "Scan" button next to "Generic MAC80211 802.11ac/b/g/n" to scan for networks, select the router you want to connect and then click the "Join Network" button,
In the network joining configuration page, turn on "Replace wireless configuration", enter the key in the "WPA passphrase" field, keep other configurations as default, click "Submit," and then click "Save",
Finally, click "Save and Apply", if normal, you can see the IP address on the FriendlyWrt homepage.

• Create wireless hotspot

Click "Network" -> "Wireless", Click the "Add" button next to "Generic MAC80211 802.11ac/b/g/n"，the "Edit wireless network" page will pop up，
Set the wireless channel in the "Operating frequency" field (e.g., "40 (5200 MHz)"),
In the "ESSID" field, input the hotspot name,
In the "Network" field, select "lan",
Click on "Wireless Security", set the encryption type, then click "Save" and "Save and Apply",
It requires a reboot to take effect, click on "System" menu, then select "Reboot".