Difference between revisions of "NanoPi NEO"

Revision as of 07:06, 10 January 2017

查看中文

1 Introduction

Overview

Front

Back

The NanoPi NEO(abbreviated as NEO) is another fun board developed by FriendlyARM for makers, hobbyists and fans.

2 Hardware Spec

CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
DDR3 RAM: 256MB/512MB
Connectivity: 10/100M Ethernet
USB Host: Type-A x 1, 2.54 mm pin x 2
MicroSD Slot x 1
MicroUSB: OTG, for power input
Debug Serial Port: 4Pin, 2.54 mm pitch pin header
GPIO: 2.54mm pitch 36pin. It includes UART, SPI, I2C, IO etc
PCB Dimension: 40 x 40 mm
Power Supply: DC 5V/2A
OS/Software: u-boot and UbuntuCore

3 Diagram, Layout and Dimension

3.1 Layout

NanoPi NEO Layout

GPIO Pin Description

Pin#	Name	Linux gpio	Pin#	Name	Linux gpio
1	SYS_3.3V		2	VDD_5V
3	I2C0_SDA		4	VDD_5V
5	I2C0_SCL		6	GND
7	GPIOG11	203	8	UART1_TX/GPIOG6	198
9	GND		10	UART1_RX/GPIOG7	199
11	UART2_TX/GPIOA0	0	12	PWM1/GPIOA6	6
13	UART2_RTS/GPIOA2	2	14	GND
15	UART2_CTS/GPIOA3	3	16	UART1_RTS/GPIOG8	200
17	SYS_3.3V		18	UART1_CTS/GPIOG9	201
19	SPI0_MOSI/GPIOC0	64	20	GND
21	SPI0_MISO/GPIOC1	65	22	UART2_RX/GPIOA1	1
23	SPI0_CLK/GPIOC2	66	24	SPI0_CS/GPIOC3	67

USB/Audio/IR Pin Description

NanoPi-NEO			NanoPi-NEO V1.1/V1.2
Pin#	Name	Description	Pin#	Name	Description
1	VDD_5V	5V Power Out	1	VDD_5V	5V Power Out
2	USB-DP1	USB1 DP Signal	2	USB-DP1	USB1 DP Signal
3	USB-DM1	USB1 DM Signal	3	USB-DM1	USB1 DM Signal
4	USB-DP2	USB2 DP Signal	4	USB-DP2	USB2 DP Signal
5	USB-DM2	USB2 DM Signal	5	USB-DM2	USB2 DM Signal
6	GPIOL11/IR-RX	GPIOL11 or IR Receive	6	GPIOL11/IR-RX	GPIOL11 or IR Receive
7	SPDIF-OUT/GPIOA17	GPIOA17 or SPDIF-OUT	7	SPDIF-OUT/GPIOA17	GPIOA17 or SPDIF-OUT
8	MICIN1P	Microphone Positive Input	8	PCM0_SYNC/I2S0_LRC	I2S/PCM Sample Rate Clock/Sync
9	MICIN1N	Microphone Negative Input	9	PCM0_CLK/I2S0_BCK	I2S/PCM Sample Rate Clock
10	LINEOUTR	LINE-OUT Right Channel Output	10	PCM0_DOUT/I2S0_SDOUT	I2S/PCM Serial Data Output
11	LINEOUTL	LINE-OUT Left Channel Output	11	PCM0_DIN/I2S0_SDIN	I2S/PCM Serial Data Input
12	GND	0V	12	GND	0V

V1.1/V1.2 Audio

Pin#	Name	Description
1	MICIN1P	Microphone Positive Input
2	MICIN1N	Microphone Negative Input
3	LINEOUTR	LINE-OUT Right Channel Output
4	GND	0V
5	LINEOUTL	LINE-OUT Left Channel Output

Debug Port（UART0）

Pin#	Name
1	GND
2	VDD_5V
3	UART_TXD0
4	UART_RXD0

Note:

SYS_3.3V: 3.3V power output
VVDD_5V: 5V power input/output. When the external device’s power is greater than the MicroUSB's the external device is charging the board otherwise the board powers the external device. The input range is 4.7V ~ 5.6V
All pins are 3.3V, output current is 5mA
For more details refer to the document: NanoPi-NEO-1606-Schematic.pdf

3.2 Dimensional Diagram

For more details refer to the document: pcb file in dxf format

4 Get Started

4.1 Essentials You Need

Before starting to use your NanoPi NEO get the following items ready

NanoPi NEO
microSD Card/TFCard: Class 10 or Above, minimum 8GB SDHC
microUSB power. A 5V/2A power is a must
A Host computer running Ubuntu 14.04 64 bit system

4.2 TF Cards We Tested

To make your NanoPi NEO boot and run fast we highly recommend you use a Class10 8GB SDHC TF card or a better one. The following cards are what we used in all our test cases presented here:

SanDisk TF 8G Class10 Micro/SD TF card:

SanDisk TF128G MicroSDXC TF 128G Class10 48MB/S:

川宇 8G C10 High Speed class10 micro SD card:

4.3 Make an Installation TF Card

4.3.1 Get Image Files

Visit this link download link to download image files and the flashing utility:

Image Files
nanopi-neo-core-qte-sd4g.img.zip	UbuntuCore with Qt-Embedded Image File
Flash Utility:
win32diskimager.rar	Windows utility for flashing Debian image. Under Linux users can use "dd"

4.3.2 Make UbuntuCore with Qt Embedded Image Card

Extract the nanopi-neo-core-qte-sd4g.img.zip and win32diskimager.rar files. Insert a TF card(at least 4G) into a Windows PC and run the win32diskimager utility as administrator. On the utility's main window select your TF card's drive, the wanted image file and click on "write" to start flashing the TF card.After flashing is done insert this TF card to your NanoPi NEO and connect the board to a 5V/2A power NEO will be automatically powered on. If the blue LED is flashing it indicates the system is being booted.

5 Work with Ubuntu-Core with Qt-Embedded

5.1 Run Ubuntu-Core with Qt-Embedded

Insert a TF card with UbuntuCore image files into your NanoPi NEO, connect the board to a 5V/2A power source the board will be automatically powered on. If you can see the blue LED flashing it means your board is working and UbuntuCore is being loaded.
If you want to do kernel development you need to use a serial communication board, ie a PSU-ONECOM board, which will allow you to operate the board via a serial terminal.
Here is a setup where we connect a NanoPi NEO to a PC via the PSU-ONECOM and you can power on your NEO from either the PSU-ONECOM or the board's MicroUSB:

It has two user names: root and fa and the password for both is "fa".
Update packages

sudo apt-get update

5.2 Ethernet Connection

If the NanoPi NEO is connected to a network via Ethernet before it is powered on it will automatically obtain an IP after it is powered up. If it is not connected via Ethernet or its DHCP is not activated obtaining an IP will fail and system will hang on for about 15 to 60 seconds.In this case you can try obtaining an IP by using the following command

dhclient eth0

5.3 Login via SSH

The NanoPi NEO doesn't have a video output interface. You can log into the board via SSH. In our test the IP address detected by our router was 192.168.1.230 and we ran the following command to log into the NanoPi NEO:

ssh root@192.168.1.230

The password is fa。

5.4 Extend TF Card's Section

We strongly recommend you to do this right after you have made an installation TF card since this will greatly enhance your NEO's experience

Solution 1: Extend your card's rootfs section under a host PC:

sudo umount /dev/sdx?
sudo parted /dev/sdx unit % resizepart 2 100 unit MB print
sudo resize2fs -f /dev/sdx2

Note: you need to replace "/dev/sdx" with the device name in your system.

Solution 2: Extend your card's rootfs section under NEO running UbuntuCore:

sudo fs_resize

Following the prompt type in "y" to start re-sizing the file system and a second "y" to reboot the NEO. After the NEO is rebooted check the new section by using the following command:

df -h

5.5 Connect USB WiFi to NEO

Our system has support for popular USB WiFi drivers. Many USB WiFi modules are plug and play with our system. Here is a list of models we tested;

Number	Model
1	RTL8188CUS/8188EU 802.11n WLAN Adapter
2	RT2070 Wireless Adapter
3	RT2870/RT3070 Wireless Adapter
4	RTL8192CU Wireless Adapter
5	MI WiFi mt7601

If you NanoPi NEO is connected to a USB WiFi and is powered up you can log into NEO and run the following command to check if the USB WiFi is recognized. If "wlan0" is listed it indicates your USB WiFi has been recognized:

ifconfig -a

Open the /etc/wpa_supplicant/wpa_supplicant.conf file and append the following lines:

network={
        ssid="YourWiFiESSID"
        psk="YourWiFiPassword"
}

The "YourWiFiESSID" and "YourWiFiPassword" need to be replaced with your actual ESSID and password.
Save, exit and run the following commands to connect to your WiFi router:

ifdown wlan0
ifup wlan0

If your WiFi password has special characters or you don't want your password saved as plain text you can use "wpa_passphrase" to generate a psk for your WiFi password. Here is how you can do it:

wpa_passphrase YourWiFiESSID

Following the prompt type in your password and you will get a new password in the /etc/wpa_supplicant/wpa_supplicant.conf file. Now you can replace the existing password in the wlan0 file with the new one.

5.6 Connect NanoPi NEO to USB Camera(FA-CAM202)

The FA-CAM202 is a 2M-pixel USB camera module. Boot your NEO, connect NEO to the internet, log in the system as root, compile and run the mjpg-streamer utility:

cd /root/mjpg-streamer
make
./start.sh

The mjpg-streamer is an open source media server. After it is started successfully you will see the following messages:

 
 i: Using V4L2 device.: /dev/video0
 i: Desired Resolution: 1280 x 720
 i: Frames Per Second.: 30
 i: Format............: YUV
 i: JPEG Quality......: 90
 o: www-folder-path...: ./www/
 o: HTTP TCP port.....: 8080
 o: username:password.: disabled
 o: commands..........: enabled

In our case our NEO's IP address was 192.168.1.123. We typed "192.168.1.123:8080" on a browser, entered and we got the following screenshot:

The mjpg-streamer uses libjpeg to soft-encode camera's input data. You can use ffmpeg to hard-encode data which greatly increases system's efficiency:

ffmpeg -t 30 -f v4l2 -channel 0 -video_size 1280x720 -i /dev/video0 -pix_fmt nv12 -r 30 -b:v 64k -c:v cedrus264 test.mp4

By default it records a 30-second video. When you type "q" it will stop recording and the recorded video will be saved as a test.mp4 file.

5.7 Check CPU's Working Temperature

Open a terminal on your NanoPi NEO and you can type the following command to read H3's temperature and frequency:

cpu_freq

5.8 Check System Information with Rpi-Monitor

Our Ubuntu-Core contains the Rpi-Monitor utility with which users can check system information and status.
In our case our NEO's IP was 192.168.1.230 and we typed the following IP in a browser:

192.168.1.230:8888

We entered the following page:

Users can easily check these system information and status.

6 Make Your Own OS

Visit download link and go to the sources directory and download nanopi-H3-bsp.
Use the 7-zip utility to uncompress it and a lihee directory and an Android directory will be generated. Or you can get it from our github:

git clone https://github.com/friendlyarm/h3_lichee.git lichee

Note: "lichee" is the project name named by Allwinner for its CPU's source code which contains the source code of U-boot, Linux kernel and various scripts.

6.1 Compile lichee Source Code

Compilation of the H3's BSP source code must be done under a PC running a 64-bit Linux.The following cases were tested on Ubuntu-14.04 LTS-64bit:

sudo apt-get install gawk git gnupg flex bison gperf build-essential \
zip curl libc6-dev libncurses5-dev:i386 x11proto-core-dev \
libx11-dev:i386 libreadline6-dev:i386 libgl1-mesa-glx:i386 \
libgl1-mesa-dev g++-multilib mingw32 tofrodos \
python-markdown libxml2-utils xsltproc zlib1g-dev:i386 u-boot-tools

Enter the lichee directory and un the following command to compile the whole package:

cd lichee
./build.sh -p sun8iw7p1 -b nanopi-h3

After this compilation succeeds a u-boot, Linux kernel and kernel modules will be generated.
Note: the lichee directory contains a cross-compiler we have setup. When the build.sh script runs it will automatically call this cross-compiler.

6.2 Package System Modules

./gen_script.sh -b nanopi-neo

This command copies the generated executables including u-boot and Linux kernel and configuration files to the "lichee/tools/pack/out/" directory and generates a script.bin file.
The script.bin file is designed by Allwinner for its CPUs. For more details refer to script.bin.

6.3 Compile U-boot

./build.sh -p sun8iw7p1 -b nanopi-h3 -m uboot

After a u-boot executable is generated some extra patches need to be patched to it. Run "./build.sh pack" to patch this executable.
If you want to manually patch the executable refer to H3_Manual_build_howto and run the following commands to update the u-boot in the TF card:

./fuse_uboot.sh /dev/sdx

Note: you need to replace "/dev/sdx" with the device name in your system.

6.4 Compile Linux Kernel

If you want to compile the Linux kernel run the following command:

./build.sh -p sun8iw7p1 -b nanopi-h3 -m kernel

After the compilation is done a uImage and its kernel modules will be generated under "linux-3.4/output".

6.5 Clean Source Code

./build.sh -p sun8iw7p1_linux -b nanopi-h3 -m clean

7 3D Printing Files

Link to 3D Printing Files

8 Other OS Support

8.1 DietPi_NanoPiNEO-armv7-(Jessie)

DietPi身轻如燕，镜像文件最小只有400M 字节（只是Raspbian Lite的三分之一）。系统存储操作及进程对资源的占用非常少，并且预装DietPi-RAMlog工具。这些特性使得用户能最大程度地发挥设备本身的性能。

仅提供给进阶爱好者交流使用，不对该系统提供专业技术支持。
烧写步骤：

下载系统固件DietPi_NanoPiNEO-armv7-(Jessie)点击下载DietPi_NanoPiNEO-armv7-(Jessie)
将文件解压后得到系统固件，在Windows下使用友善官方提供 win32diskimager 工具烧写即可。
烧写完成后，将TF卡插入NanoPi NEO，上电即可体验DietPi_NanoPiNEO-armv7-(Jessie)。

登录账号：root; 登录密码：dietpi

8.2 Armbian

Armbian releases Armbian_5.20_Nanopineo_Debian_jessie_3.4.112 and Armbian_5.20_Nanopineo_Ubuntu_xenial_3.4.112 for the NanoPi NEO. You can refer to its home page for more details.
home page: http://www.armbian.com/nanopi-neo/

8.3 FreeBSD

Thanks to Ganbold Tsagaankhuu FreeBSD runs on NEO. He has created FreeBSD 12.0-CURRENT image and it can be downloaded from: https://www.mediafire.com/folder/bfbs771c3ajar/FreeBSD

9 Resources

Schematics
Dimensional Diagram
- NanoPi-NEO-1606 pcb file in dxf format
- NanoPi-NEO-V1.1-1608 pcb file in dxf format
H3 Datesheet Allwinner_H3_Datasheet_V1.2.pdf
Matrix Modules & Wiki Sites:

10 Update Log

10.1 July-07-2016

Released English Version

10.2 August-09-2016

Added Other OS Support

10.3 Sep-08-2016

Added Section 7
Updated sections 5.3, 5.5 and 9

10.4 Nov-03-2016

Added Section 5.6

10.5 Dec-20-2016

Added Section 5.8

@@ Line 353: / Line 353: @@
 ==Other OS Support==
+===DietPi_NanoPiNEO-armv7-(Jessie)===
+DietPi身轻如燕，镜像文件最小只有400M 字节（只是Raspbian Lite的三分之一）。系统存储操作及进程对资源的占用非常少，并且预装DietPi-RAMlog工具。这些特性使得用户能最大程度地发挥设备本身的性能。<br />
+仅提供给进阶爱好者交流使用，不对该系统提供专业技术支持。 <br />
+烧写步骤：
+*下载系统固件DietPi_NanoPiNEO-armv7-(Jessie)点击下载[http://dietpi.com/downloads/images/DietPi_NanoPiNEO-armv7-(Jessie).7z DietPi_NanoPiNEO-armv7-(Jessie)]
+*将文件解压后得到系统固件，在Windows下使用友善官方提供 win32diskimager 工具烧写即可。
+*烧写完成后，将TF卡插入NanoPi NEO，上电即可体验DietPi_NanoPiNEO-armv7-(Jessie)。
+登录账号：root; 登录密码：dietpi
 ===Armbian===
+Armbian releases Armbian_5.20_Nanopineo_Debian_jessie_3.4.112 and Armbian_5.20_Nanopineo_Ubuntu_xenial_3.4.112 for the NanoPi NEO. You can refer to its home page for more details.<br />
 home page: http://www.armbian.com/nanopi-neo/