Difference between revisions of "NanoPC-T2"

Revision as of 09:20, 28 April 2016

查看中文

1 Introduction
2 Features
3 Diagram, Layout and Dimension
- 3.1 Layout
- 3.2 Board Dimension
4 Notes in Hardware Design
- 4.1 EEPROM
5 Get Started
6 Working with Debian
7 Make Your Own OS Image
8 Connect NanoPC-T2 to External Modules
9 Extend NanoPC-T2's SD Card Section
- 9.1 Debian
- 9.2 Android
10 Source Code and Image Files Download Links
11 Resources
12 Tech Support
13 Update Log

1 Introduction

Overview

Front

Back

The NanoPC-T2 quad core Cortex A9 single board computer is designed and developed by FriendlyARM for professional and enterprise users. It uses the Samsung Quad Core Cortex-A9 S5P4418 SoC with dynamic frequency scaling up to 1.4GHz. Compared to FriendlyARM's existing 4418 based boards the NanoPC-T2 has 8G eMMC onboard, audio jack and video input/output interfaces. Compared to its predecessor the NanoPC-T1 the NanoPC-T2 has built-in WiFi, Bluetooth and Gbps Ethernet port. In addition the NanoPC-T2 has power management which the NanoPC-T1 doesn't support. To avoid overheat issues the NanoPC-T2 has a heat sink with mounting posts.
The NanoPC-T2 combines all the ports and interfaces the existing FriendlyARM 4418 boards have. Currently it has the most interfaces and ports among all existing ARM boards of this size. Its rich video interfaces and support for HDMI 1080P enable it to work with not only popular display devices but also various FriendlyARM LCDs (both resistive touch and capacitive touch).
The NanoPC-T2 is FriendlyARM's most complete solution based on Samsung 4418 for both commercial and industrial applications.

2 Features

SoC： Samsung S5P4418 Quad Core Cortex-A9 with dynamic frequency scaling up to 1.4G Hz
Power Management Unit： AXP228 PMU, it supports software power-off and wake-up.
System Memory： 1GB 32bit DDR3 RAM
eMMC： 8GB
Storage： 1 x SD Card Slot
Ethernet： Gbps Ethernet Port (RTL8211E) with unique MAC
WiFi： 802.11b/g/n
Bluetooth： 4.0 dual mode
Antenna： Porcelain Antenna IPX Interface
Video Input: DVP Camera/MIPI-CSI (two camera interfaces)
Video Output: HDMI Type-A / LVDS / LCD / MIPI DSI (four video output interfaces)
Audio: 3.5 mm audio jack / via HDMI
Microphone: 1 x onboard Microphone
USB: 4 x USB 2.0 Host, two standard type A ports and two 2.54mm pitch pin headers
MicroUSB: 1 x MicroUSB 2.0 Client, Type A
LCD Interface： 0.5mm pitch 45 pin FPC seat, full color RGB 8-8-8
HDMI: 1.4A Type A, 1080P
DVP Camera: 0.5mm pitch 24 pin FPC seat
GPIO: 2.54 mm pitch 30 pin header
Serial Debug Port: 2.54mm pitch 4pin header
LED: 1 x power LED , 2 x GPIO LED
User Key: 1 x K1 (power), 1 x Reset
Other Resource: 1 x onboard thermistor
RTC Battery： RTC Seat Pins
Power: DC 5V/2A
Heat Sink: 1 x Heat Sink with mounting holes
PCB: Six Layer
PCB Dimension: 100 mm x 60 mm
OS/Software: u-boot, Android5.1, Debian8

3 Diagram, Layout and Dimension

3.1 Layout

NanoPC-T2 Layout

30Pin GPIO Pin Spec

Pin#	Name	Pin#	Name
1	SYS_3.3V	2	DGND
3	UART2_TX/GPIOD20	4	UART2_RX/GPIOD16
5	I2C0_SCL	6	I2C0_SDA
7	SPI0_MOSI/GPIOC31	8	SPI0_MISO/GPIOD0
9	SPI0_CLK/GPIOC29	10	SPI0_CS/GPIOC30
11	UART3_TX/GPIOD21	12	UART3_RX/GPIOD17
13	UART4_TX/GPIOB29	14	UART4_RX/GPIOB28
15	GPIOB31	16	GPIOB30
17	GPIOC4	18	GPIOC7
19	GPIOC8	20	GPIOC24
21	GPIOC28	22	GPIOB26
23	GPIOD1/PWM0	24	GPIOD8/PPM
25	GPIOC13/PWM1	26	AliveGPIO3
27	GPIOC14/PWM2	28	AliveGPIO5
29	VDD_5V	30	DGND

20Pin LVDS Interface Pin Spec

Pin#	Name	Pin#	Name
1	SYS_3.3V	2	SYS_3.3V
3	GPIOC16	4	GPIOB18
5	DGND	6	DGND
7	LVDS_D0-	8	LVDS_D0+
9	LVDS_D1-	10	LVDS_D1+
11	LVDS_D2-	12	LVDS_D2+
13	DGND	14	DGND
15	LVDS_CLK-	16	LVDS_CLK+
17	LVDS_D3-	18	LVDS_D3+
19	I2C2_SCL	20	I2C2_SDA

DVP Camera Interface Pin Spec

Pin#	Name
1, 2	SYS_3.3V
7,9,13,15,24	DGND
3	I2C0_SCL
4	I2C0_SDA
5	GPIOB14
6	GPIOB16
8,10	NC
11	VSYNC
12	HREF
14	PCLK
16-23	Data bit7-0

RGB LCD IF Pin Spec

Pin#	Name	Description
1, 2	VDD_5V	5V Output, it can be used to power LCD modules
11，20，29, 37，38，39，40, 45	DGND	Ground
3-10	Blue LSB to MSB	RGB blue
12-19	Green LSB to MSB	RGB green
21-28	Red LSB to MSB	RGB red
30	GPIOB25	available for users
31	GPIOC15	occupied by FriendlyARM one wire technology to recognize LCD models and control backlight and implement resistive touch, not applicable for users
32	XnRSTOUT Form CPU	low when system is reset
33	VDEN	signal the external LCD that data is valid on the data bus
34	VSYNC	vertical synchronization
35	HSYNC	horizontal synchronization
36	LCDCLK	LCD clock, Pixel frequency
41	I2C2_SCL	I2C2 clock signal, for capacitive touch data transmission
42	I2C2_SDA	I2C2 data signal, for capacitive touch data transmission
43	GPIOC16	interrupt pin for capacitive touch, used with I2C2
44	NC	Not connected

MIPI-DSI Interface Pin Spec

Pin#	Name
1, 2, 3	VDD_5V
4	DGND
5	I2C2_SDA
6	I2C2_SCL
7	DGND
8	GPIOC0
9	DGND
10	GPIOC1
11	DGND
12	GPIOA28
13	nRESETOUT
14, 15	DGND
16	MIPIDSI_DN3
17	MIPIDSI_DP3
18	DGND
19	MIPIDSI_DN2
20	MIPIDSI_DP2
21	DGND
22	MIPIDSI_DN1
23	MIPIDSI_DP1
24	DGND
25	MIPIDSI_DN0
26	MIPIDSI_DP0
27	DGND
28	MIPIDSI_DNCLK
29	MIPIDSI_DPCLK
30	DGND

MIPI-CSI Interface Pin Spec

Pin#	Name
1, 2	SYS_3.3V
3	DGND
4	I2C0_SDA
5	I2C0_SCL
6	DGND
7	SPI2_MOSI/GPIOC12
8	SPI2_MISO/GPIOC11
9	SPI2_CS/GPIOC10
10	SPI2_CLK/GPIOC9
11	DGND
12	GPIOB9
13	GPIOC2
14, 15	DGND
16	MIPICSI_DN3
17	MIPICSI_DP3
18	DGND
19	MIPICSI_DN2
20	MIPICSI_DP2
21	DGND
22	MIPICSI_DN1
23	MIPICSI_DP1
24	DGND
25	MIPICSI_DN0
26	MIPICSI_DP0
27	DGND
28	MIPICSI_DNCLK
29	MIPICSI_DPCLK
30	DGND

Note:

SYS_3.3V: 3.3V power output
VDD_5V: 5V power input/output. The input range is 4.7V ~ 5.6V
For more details refer to the document: NanoPC-T2_1601B_Schematic.pdf

3.2 Board Dimension

For more details refer to the document: NanoPC-T2-Dimensions(dxf)

Power Jack

DC 4.7~5.6V IN, 4.0*1.7mm Power Jack

4 Notes in Hardware Design

4.1 EEPROM

The board has an EEPROM(model: 24AA025E48T-I/OT) with a unique MAC. This EEPROM is connected to I2C0 and its address is 0x51 therefore some EEPROM chips cannot be connected to I2C0 which will cause conflicts of addresses.
In our tests these EEPROM chips cannot be connected to I2C0: 24C04, 24C08 and 24C16. There chips which we tested can be connected to I2C0: 24C01, 24C02 and 24C256
For more details about EEPROM address issues refer to http://www.onsemi.com/pub_link/Collateral/CAT24C01-D.PDF

5 Get Started

5.1 Essentials You Need

Before starting to use your NanoPC-T2 get the following items ready

NanoPC-T2
SD Card: Class 10 or Above, minimum 8GB SDHC
A DC 5V/2A power is a must
HDMI monitor or LCD
USB keyboard, mouse and possible a USB hub(or a TTL to serial board)
A host computer running Ubuntu 14.04 64 bit system

5.2 Make an Installation SD Card

5.2.1 Boot NanoPC-T2 from SD Card

Get the following files from here download link:

Get a 4G SDHC card and backup its data if necessary.

For LCD or HDMI output use the following files:
nanopi2-debian-sd4g.img.zip	Debian image files (there two Debian files)
nanopi2-android-sd4g.img.zip	Android image files
Flash Utility:
win32diskimager.rar	Windows utility. Under Linux users can use "dd"

Uncompress these files. Insert an SD card(at least 4G) into a Windows PC and run the win32diskimager utility as administrator. On the utility's main window select your SD card's drive, the wanted image file and click on "write" to start flashing the SD card.
Insert this card into your NanoPC-T2's boot slot, press and hold the boot key and power on (with a 5V/2A power source). If the PWR LED is on and LED1 is blinking this indicates your NanoPC-T2 has successfully booted.

5.2.2 Boot NanoPC-T2 from eMMC

Download RAW Image

Get the image file: nanopi2-eflasher-sd4g.img.zip and the Windows utility: win32diskimager.rar;

Flash RAW Image to SD Card

Insert an SD card(at least 4G) into a Windows PC and run the win32diskimager utility as administrator. On the utility's main window select your SD card's drive, the wanted image file and click on "write" to start flashing the SD card

Prepare RAW image

Go to this link [1] to download Android and Debian image files(System-image-files-for-eMMC). After download untar the ".tgz" ball and copy the files to your SD card.

OS	Image	Files	Copy to...
Android 5.1	android-lollipop-images.tgz android-lollipop-images.tgz.hash.md5	boot.img system.img userdata.img cache.img partmap.txt	images\android
Debian (Jessie)	debian-jessie-images.tgz debian-jessie-images.tgz.hash.md5	boot.img rootfs.img partmap.txt	images\debian

Specify OS

By default the SD card's configuration file "images\FriendlyARM.ini" specifies Android to be flashed to eMMC. If you want to install Debian make the following change:

OS = Debian

"#" is a comment

Flash Image to NanoPC-T2's eMMC

Insert this card into your NanoPC-T2, connect the board to an HDMI monitor or an LCD, press and hold the boot key and power on (with a 5V/2A power source) the board to start installation. You can watch the whole installation process from the HDMI monitor or LCD. If the following messages pop up it means the installation has succeeded.

Android is fused successfully. 
All done.

After installation is done do "reset" or power off and on the board to boot the board from eMMC.

You can check the LED's status to monitor the installation process too

LED Status	Installation Status
LED1 blinks twice continuously LED2 off	Power on normal. If installation doesn't proceed LED1 will keep behaving this way and LED2 will be off
LED1 and LED2 blink alternatively with each blink for 0.3s	Installation proceeding
LED1 and LED2 blink alternatively with each blink for 1.2s	Installation succeeded
LED1 and LED2 blink simultaneously	Installation failed

5.2.3 Make Installation Card under Linux Desktop

1) Insert your SD card into a host computer running Ubuntu and check your SD card's device name

dmesg | tail

Search the messages output by "dmesg" for similar words like "sdc: sdc1 sdc2". If you can find them it means your SD card has been recognized as "/dev/sdc". Or you can check that by commanding "cat /proc/partitions"

2) Downlaod Linux script

git clone https://github.com/friendlyarm/sd-fuse_nanopi2.git
cd sd-fuse_nanopi2

3) Make Android SD Card

su
./fusing.sh /dev/sdx

(Note: you need to replace "/dev/sdx" with the device name in your system)
When you run the script for the first time it will prompt you to download an image you have to hit “Y” within 10 seconds otherwise you will miss the download

4) Here is how to make a Debian SD card

./fusing.sh /dev/sdx debian

5.2.4 LCD/HDMI Resolution

When the system boots our uboot will check whether it is connected to an LCD or to an HDMI monitor. If it recognizes an LCD it will configure its resolution. Our uboot defaults to the HDMI 720P configuration.
If you want to modify the LCD resolution you can modify file "arch/arm/plat-s5p4418/nanopi2/lcds.c" in the kernel and recompile it.
If your NanoPC-T2 is connected to an HDMI monitor and it runs Android it will automatically set the resolution to an appropriate HDMI mode by checking the "EDID". If your NanoPC-T2 is connected to an HDMI monitor and it runs Debian by default it will set the resolution to the HDMI 720P configuration. If you want to modify the HDMI resolution to 1080P modify your kernel's configuration as explained above.

5.3 Update Image Files in SD Card From PC Host

If you want to make some changes to the image files in your SD card follow the steps below otherwise you can skip this section.
Insert your SD card into a host PC running Linux, mount the boot and rootfs sections of the SD card and follow the steps below:
1) If you want to change your kernel command line parameters you can do it via the fw_setevn utility under "sd-fuse_nanopi2/tools".
Check the current Command Line:

cd sd-fuse_nanopi2/tools
./fw_printenv /dev/sdc | grep bootargs

Android 5.1.1_r6 starts SELinux. By default it is enforcing. You can change it this way:

./fw_setenv /dev/sdc bootargs XXX androidboot.selinux=permissive

This sets it to "permissive". The "XXX" stands for the original bootargs' value.

2) Update Kernel
Our customized uboot will check the LCD type when it boots.
For a non-Android OS if it recognizes that an LCD is connected to the NanoPC-T2 it will load "uImage" from "boot" otherwise it will load "uImage.hdmi".
For Android it doesn't make any difference which display device is detected. You can use your generated uImage to replace the existing one under "boot".
For Debian if your generated kernel is for an LCD you need to replace the existing uImage or if your kernel is for an HDMI monitor you need to replace the existing uImage.hdmi.

5.4 Run Android or Debian

Insert an SD card with Android/Debian image file into your NanoPC-T2, connect the board to an HDMI monitor, press and hold the boot key, power on the board the NanoPC-T2 will boot from the SD card. If you can see the PWR LED on and the LED1 flashing it means your board is working and you will see Android/Debain being loaded on the HDMI monitor.

1）If you connect the NanoPC-T2 to an HDMI monitor you need to use a USB mouse and a USB keyboard to operate. If you connect it to an LCD with capacitive touch you can operate directly on the LCD.
2）If you want to do kernel development you need to use a serial communication board, ie a PSU-ONECOM board, which will allow you to operate the board via a serial terminal.

Here is a setup where we connect a NanoPC-T2 to a PC running Ubuntu and Minicom via a serial cable you will see system messages output to the PC’s minicom terminal:

Under Debian the password for "root" is "fa"

5.5 Login to Debian via VNC or SSH

If your NanoPC-T2 is not connected to a display device and your board runs the "-wifiap.img" image you can login to your NanoPC-T2's nanopi2-wifiap(the default password is "123456789") via a mobile phone. You can download and install a "VNC Viewer" from here on a mobile phone and login to the NanoPC-T2 via VNC. Its default password is "fa123456". Here is a screenshot which shows how it looks like when users login to the NanoPC-T2 from an iPhone via VNC:

You can login via "SSH -l root 192.168.8.1" the default password for "root" is "fa"

To make SSH session run faster turn off the WiFi's power saving mode by using the following command:

iwconfig wlan0 power off

6 Working with Debian

6.1 Ethernet Connection

If the NanoPC-T2 is connected to a network via Ethernet before it is powered on, it will automatically obtain an IP after it is powered up.

6.2 Wireless Connection

The following section only applies to the NanoPC-T2 which is connected to an HDMI monitor or an LCD

When the board runs Debian after it is fully loaded click on the network icon on the GUI. It will automatically search for nearby WiFi sources. Select a source from the list, click on its "Properties", type in its password, save, close and then "Connect".

The following section only applies to the NanoPC-T2 which is not connected to any display device(ie running "-wifiap.img")

By default the system's WiFi AP mode is on therefore it cannot search and connect to a wireless router. You need to turn off the WiFi AP mode by following the instructions below: Firstly set up the WiFi router you expect to connect to:
Login to the NanoPC-T2 via SSH. Check the WiFi device by running the following commands. Those starting with "wlan" are WiFi devices:

ifconfig -a

By default "wlan0" is the Wifi device. You need to create a configuration file with the same name under "/etc/network/interfaces.d/". For instance you can create a "wlan0" file:

vi /etc/network/interfaces.d/wlan0

Here is the wlan0's content:

auto wlan0
iface wlan0 inet dhcp
wpa-ssid YourWiFiESSID
wpa-ap-scan 1
wpa-psk YourWiFiPassword

The "YourWiFiESSID" and "YourWiFiPassword" need to be replaced with your actual ESSID and password.

If your WiFi password has special characters or you don't want your password saved as plain text you can use "wpa_passphrase" to generate a psk for your WiFi password. Here is how you can do it:

wpa_passphrase YourWiFiESSID

Following the prompt type in your password and you will get some code in the following format. The string after "psk=" is your new password:

network={
        ssid="YourWiFiESSID"
        #psk="YourWiFiPassword"
        psk=1b66ca678d6f439f7360686ff5eeb7519cdc44b76a40d96515e4eb807a6d408b
}

Now you can replace the existing password in the wlan0 file with the new one:

auto wlan0
iface wlan0 inet dhcp
wpa-ssid YourWiFiESSID
wpa-ap-scan 1
wpa-psk 1b66ca678d6f439f7360686ff5eeb7519cdc44b76a40d96515e4eb807a6d408b

Next turn off the AP mode. You need to do this as root. Run the following commands and your system will be rebooted. After your system is rebooted it will automatically connect to the WiFi router you set up in your first step:

su
turn-wifi-into-apmode no

6.3 Setup Wi-Fi AP

You can follow the steps below to setup Wi-Fi AP:

turn-wifi-into-apmode yes

Reboot the system as prompted. By default the AP's name is "nanopi2-wifiap" and the password is 123456789.

Now you are able to find the "nanopi2-wifiap" from a host PC and connect to it. If a connection is successful you will be able to SSH to this NanoPC-T2 at "192.168.8.1":

ssh root@192.168.8.1

The password for it is "fa"

To make SSH session run faster turn off the WiFi's power saving mode by using the following command:

iwconfig wlan0 power off

You can check the WiFi mode via the following command:

cat /sys/module/bcmdhd/parameters/op_mode

If the result is "2" it means it is currently working as a WiFi AP.If you want to switch back to the Station mode you can do it this way:

turn-wifi-into-apmode no

6.4 Bluetooth

Click on the bluetooth icon on the GUI a menu will pop up:
Make discoverable... enables the NanoPC-T2 to be searched for by nearby bluetooth devices;
Devices... opens a search window and searches for nearby bluetooth devices(Note: the "Make discoverable" property needs to be enabled on those nearby devices as well);
Send Files to Device...enables the NanoPC-T2 to send files to another bluetooth device which is paired to the NanoPC-T2

6.5 Install Debian Packages

We provide a Debian Jessie image. You can install Jessie's packages by commanding "apt-get". If this is your first installation you need to update the package list by running the following command

apt-get update

You can install your preferred packages. For example if you want to install an FTP server you can do this:

apt-get install vsftpd

Note: you can change your download server by editting "/etc/apt/sources.list". You can get a complete server list from [2]. You need to select the one with "armhf".

7 Make Your Own OS Image

7.1 Install Cross Compiler

Download the compiler package:

git clone https://github.com/friendlyarm/prebuilts.git
sudo mkdir -p /opt/FriendlyARM/toolchain
sudo tar xf prebuilts/gcc-x64/arm-cortexa9-linux-gnueabihf-4.9.3.tar.xz -C /opt/FriendlyARM/toolchain/

Then add the compiler's directory to "PATH" by appending the following lines in "~/.bashrc":

export PATH=/opt/FriendlyARM/toolchain/4.9.3/bin:$PATH
export GCC_COLORS=auto

Execute "~/.bashrc" to make the changes take effect. Note that there is a space after the first ".":

. ~/.bashrc

This compiler is a 64-bit one therefore it cannot be run on a 32-bit Linux machine. After the compiler is installed you can verify it by running the following commands:

arm-linux-gcc -v
Using built-in specs.
COLLECT_GCC=arm-linux-gcc
COLLECT_LTO_WRAPPER=/opt/FriendlyARM/toolchain/4.9.3/libexec/gcc/arm-cortexa9-linux-gnueabihf/4.9.3/lto-wrapper
Target: arm-cortexa9-linux-gnueabihf
Configured with: /work/toolchain/build/src/gcc-4.9.3/configure --build=x86_64-build_pc-linux-gnu
--host=x86_64-build_pc-linux-gnu --target=arm-cortexa9-linux-gnueabihf --prefix=/opt/FriendlyARM/toolchain/4.9.3
--with-sysroot=/opt/FriendlyARM/toolchain/4.9.3/arm-cortexa9-linux-gnueabihf/sys-root --enable-languages=c,c++
--with-arch=armv7-a --with-tune=cortex-a9 --with-fpu=vfpv3 --with-float=hard
...
Thread model: posix
gcc version 4.9.3 (ctng-1.21.0-229g-FA)

7.2 Compile U-Boot

Download the U-Boot source code and compile it. Note that the github's branch is nanopi2-lollipop-mr1:

git clone https://github.com/friendlyarm/uboot_nanopi2.git
cd uboot_nanopi2
git checkout nanopi2-lollipop-mr1
make s5p4418_nanopi2_config
make CROSS_COMPILE=arm-linux-

After your compilation succeeds a u-boot.bin will be generated. If you want to test it flash it to your installation SD card via fastboot. Here is how you can do it:
1) On your host PC run "sudo apt-get install android-tools-fastboot" to install the fastboot utility;
2) Connect your NanoPC-T2 to your host PC via a serial cable (e.g. PSU-ONECOME). Press the enter key within two seconds right after you power on your NanoPC-T2 and you will enter uboot's command line mode;
3) After type in "fastboot" and press "enter" you will enter the fastboot mode;
4) Connect your NanoPC-T2 to this host PC via a microUSB cable and type in the following command to flash u-boot.bin:

fastboot flash bootloader u-boot.bin

Warning: you cannot update this SD card by commanding "dd". This command will cause trouble when booting the NanoPC-T2.

7.3 Prepare mkimage

You need the mkimage utility to compile a U-Boot source code package. Make sure this utility works well on your host before you start compiling a uImage.
You can install this utility by either commanding "sudo apt-get install u-boot-tools" or following the commands below:

cd uboot_nanopi2
make CROSS_COMPILE=arm-linux- tools
sudo mkdir -p /usr/local/sbin && sudo cp -v tools/mkimage /usr/local/sbin

7.4 Compile Linux Kernel

7.4.1 Compile Kernel

Download Kernel Source Code

git clone https://github.com/friendlyarm/linux-3.4.y.git
cd linux-3.4.y
git checkout nanopi2-lollipop-mr1

The NanoPC-T2's kernel source code lies in the "nanopi2-lollipop-mr1" branch.

Compile Android Kernel

make nanopi2_android_defconfig
touch .scmversion
make uImage

Compile Debian Kernel

make nanopi2_linux_defconfig
touch .scmversion
make uImage

After your compilation succeeds a uImage will be generated in the "arch/arm/boot/uImage" directory. This kernel is for HDMI 720P. You can use it to replace the existing uImage.hdmi.
If you want to generate a kernel for HDMI 1080P you can do it this way:

touch .scmversion
make nanopi2_linux_defconfig
make menuconfig
  Device Drivers -->
    Graphics support -->
      Nexell Graphics -->
        [ ] LCD
        [*] HDMI
        (0)   Display In  [0=Display 0, 1=Display 1]
              Resolution (1920 * 1080p)  --->
make uImage

After your compilation succeeds a uImage will be generated for HDMI 1080P. You can use it to replace the existing uImage.

7.4.2 User Your Generated Kernel

Update the kernel file in SD card

If you use an SD card to boot Android you can copy your generated uImage file to your SD card's boot section(e.g. section 1 /dev/sdX1).
If you use an SD card to Debian and you generated a uImage for an HDMI monitor you can use that uImage to replace the uImage.hdmi file in the SD card's boot section. If you use an SD card to Debian and you generated a uImage for an LCD you can use that uImage to replace the uImage file in the SD card's boot section.

Update Android kernel file in eMMC

If you want to update the kernel file in eMMC you need firstly boot your board, then mount eMMC's boot section, replace the boot section's kernel file with your generated one and reboot your board to make your new kernel run.
If you boot your board from eMMC you can update your kernel file by following the steps below:
1) After Android is loaded mount eMMC's boot section (in our example eMMC's device name was /dev/mmcblk0p1) by using the following commands:

su
mount -t ext4 /dev/block/mmcblk0p1 /mnt/media_rw/sdcard1/

2) Connect your board to a host PC running Ubuntu and copy the uImage file to eMMC's boot section by running the following commands

adb push uImage /mnt/media_rw/sdcard1/

3) Or you can copy your generated kernel file to an external storage card(e.g. an SD card or a USB drive), connect the storage card to your board the move the file from the card to eMMC's boot section
4) After update is done type in "reboot" to reload Android. Note don't directly power off and on the board or press the reset button to reboot the board. These two actions will damage your kernel file

Update Debian kernel file in eMMC

If you boot your board from eMMC you can update your kernel file by following the steps below:
1) When Debian is being loaded eMMC's boot section will be automatically mounted(in our example eMMC's device name was /dev/mmcblk0p1). You can use "mount" to verify that
2) Connect your board to a host PC via Ethernet and copy your generated uImage file via scp/ftp to eMMC's boot section and replace the existing file. If your file is for an LCD use your uImage file to replace the existing uImage. If your file is for an HDMI monitor use your uImage.hdmi file to replace the existing uImage.hdmi file
3) Or you can copy your generated kernel file to an external storage card(e.g. an SD card or a USB drive), connect the storage card to your board the move the file from the card to eMMC's boot section
4) After update is done type in "reboot" to reload Android. Note don't directly power off and on the board or press the reset button to reboot the board. These two actions will damage your kernel file

Generate Your boot.img

If you want to generate an image file that can be flashed to eMMC you need to generate a boot.img file and copy it to your installation SD card
For Android copy the uImage file to Android source code's "device/friendly-arm/nanopi2/boot/" directory and compile this whole Android source code. After your compilation is successful you will get a boot.img file.
For Debian follow the steps below to generate a boot.img file
1) Download debian_nanopi2

git clone https://github.com/friendlyarm/debian_nanopi2.git

2) Copy the image file for an HDMI monitor and use it to replace the "debian_nanopi2/boot/uImage.hdmi" file and copy the image file for an LCD and use it to replace the "debian_nanopi2/boot/uImage" file
3) Generate Debian's boot.img

cd debian_nanopi2
mkdir rootfs
./build.sh

A newly generated boot.img will be under the "debian_nanopi2/sd-fuse_nanopi2/debian" directory.
The "mkdir rootfs" command creates a working directory for the build.sh script to run. It also creates some files such as "rootfs.img" but these files are useless.

7.4.3 Compile Kernel Modules

Android contains kernel modules which are in the "/lib/modules" directory in the system section. If you want to add your own modules to the kernel or you changed your kernel configurations you need to recompile these new modules.
Compile Original Kernel Modules:

cd linux-3.4.y
make CROSS_COMPILE=arm-linux- modules

Here we have two new modules and we can compile them by following the commands below:

cd /opt/FriendlyARM/s5p4418/android
./vendor/friendly-arm/build/common/build-modules.sh

The "/opt/FriendlyARM/s5p4418/android" directory points to the top directory of Android source code. You can get more details by specifying option "-h".
After your compilation succeeds new modules will be generated

7.5 Compile Android

Install Cross Compiler

Install 64 bit Ubuntu 14.04 on your host PC.

sudo apt-get install bison g++-multilib git gperf libxml2-utils make python-networkx zip
sudo apt-get install flex libncurses5-dev zlib1g-dev gawk minicom

For more details refer to https://source.android.com/source/initializing.html 。

Download Source Code

You need to use repo to get the Android source code. Refer to https://source.android.com/source/downloading.html 。

mkdir android && cd android
repo init -u https://github.com/friendlyarm/android_manifest.git -b nanopi2-lollipop-mr1
repo sync

The "android" directory is the working directory.

Compile System Package

source build/envsetup.sh
lunch aosp_nanopi2-userdebug
make -j8

After your compilation succeeds an image will be generated in the "out/target/product/nanopi2/" directory.

Flash Image to eMMC

After compiling Android successfully you can flash it to eMMC with either of the following methods
1) fastboot: right after the NanoPC-T2 is booted from eMMC press any key to enter the uboot commandline mode and type in "fastboot"
Connect your board to a host PC running Ubuntu with a USB cable and run the following commands in the PC's terminal:

cd out/target/product/nanopi2
sudo fastboot flash boot boot.img
sudo fastboot flash cache cache.img
sudo fastboot flash userdata userdata.img
sudo fastboot flash system system.img
sudo fastboot reboot

2) Use an SD Card
Copy these files: boot.img, cache.img, userdata.img, system.img, partmap.txt from the out/target/product/nanopi2 directory to your installation SD card's images/android directory and you can use this SD card to flash Android to eMMC

8 Connect NanoPC-T2 to External Modules

8.1 Connect NanoPC-T2 to USB Camera(FA-CAM202)

In this use case the NanoPC-T 2 runs Debian. If you connect your NanoPC-T2 to our LCD or an HDMI monitor after Debain is fully loaded click on "other"-->"xawtv9" on the left bottom of the GUI and the USB Camera application will be started. After enter "welcome to xawtv！" click on "OK" to start exploring.

8.2 Connect NanoPC-T2 to CMOS 5M-Pixel Camera

In this use case the NanoPC-T2 runs Android5.1. If you connect your NanoPC-T2 to our LCD or an HDMI monitor after Android is fully loaded click on the "Camera" icon and the application will be started.

8.3 Use OpenCV to Access USB Camera

The full name of "OpenCV" is Open Source Computer Vision Library and it is a cross platform vision library.
When the NanoPC-T2 runs Debian users can use OpenCV APIs to access a USB Camera device.

1. Here is a guideline on how to use OpenCV with C++ on the NanoPC-T2:

Firstly you need to make sure your NanoPC-T2 is connected to the internet.Login to your NanoPC-T2 via a serial terminal or SSH. After login type in your username(root) and password(fa):
Run the following commands:

apt-get update
apt-get install libcv-dev libopencv-dev

2. Make sure your USB camera works with the NanoPC-T2. You can test your camera with NanoPC-T2's camera utility.
3. Check your camera device:

ls /dev/video*

Note:in our test case video9 was available and video0 to video8 were occupied

4. OpenCV's code sample(official code in C++) is under /home/fa/Documents/opencv-demo. Compile the code sample with the following commands:

cd /home/fa/Documents/opencv-demo
make

After it is compiled successfully a "demo" executable will be generated

5. Note: the NanoPC-T2 has nine video devices. However this OpenCV's code sample defines a maximum of 8 cameras can be accessed therefore one video needs to be removed. Here we removed video0:

rm /dev/video0
mv /dev/video9 /dev/video0

6. Connect NanoPi 2 to USB Keyboard & Run the Following Command:

./demo

8.4 Connect NanoPC-T2 to Matrix GPS Module

The Matrix-GPS module is a small GPS module with high performance. It can be used in navigation devices, four-axle drones and etc.
The Matrix-GPS module uses serial communication. When the NanoPC-T2 is connected to the Matrix GPS module, after the NanoPC-T2 is powered up type in the following command in a terminal or click on the xgps icon it will be started.

$su - fa -c "DISPLAY=:0 xgps 127.0.0.1:9999"

Or on the Debian GUI start the LXTerminal, type in "xgps" and enter it will be started too.

For more details about this GPS module refer to this link
Refer to the following diagram to connect the NanoPC-T2 to the Matrix-GPS:

Connection Details:

Matrix-GPS	NanoPC-T2
RXD	Pin8
TXD	Pin10
5V	Pin4
GND	Pin6

9 Extend NanoPC-T2's SD Card Section

9.1 Debian

Run the following commands on a host PC's terminal:

sudo umount /dev/sdx?
sudo parted /dev/sdx unit % resizepart 2 100 unit MB print
sudo resize2fs -f /dev/sdx2

9.2 Android

Run the following commands on a host PC's terminal:

sudo umount /dev/sdx?
sudo parted /dev/sdx unit % resizepart 4 100 resizepart 7 100 unit MB print
sudo resize2fs -f /dev/sdx7

(Note: you need to replace "/dev/sdx" with the device name in your system)

10 Source Code and Image Files Download Links

Image File: [3]
Source Code: [4]

11 Resources

《创客秘籍》Hacker's Book in Chinese by FriendlyARM
《创客秘籍-02》Hacker's Book-02 in Chinese by FriendlyARM
SEC_Users_Manual_S5P4418_Users_Manual_Preliminary[5]
Schematic(NanoPC-T2_1601B_Schematic.pdf)
PCB Dimension(NanoPC-T2-Dimensions(dxf))
Component-Position-Diagram([6])
Matrix Modules & Wiki Sites:

12 Tech Support

If you have any further questions please visit our forum[7] and post a message or email us at techsupport@friendlyarm.com. We will endeavor to get back to you as soon as possible.

13 Update Log

13.1 March-04-2016

Released English version

13.2 March-09-2016

Corrected a typo

13.3 March-23-2016

Added section 11

13.4 March-27-2016

Corrected expression errors

13.5 April-08-2016

Added section 6.4.2 and 7.4
Updated section 6.5

@@ Line 553: / Line 553: @@
 Make discoverable... enables the NanoPC-T2 to be searched for by nearby bluetooth devices;<br />
 Devices... opens a search window and searches for nearby bluetooth devices(Note: the "Make discoverable" property needs to be enabled on those nearby devices as well);<br />
-Send Files to Device...enables the NanoPi2 to send files to another bluetooth device which is paired to the NanoPC-T2<br />
+Send Files to Device...enables the NanoPC-T2 to send files to another bluetooth device which is paired to the NanoPC-T2<br />
 ===Install Debian Packages===