Difference between revisions of "Template:OfficialUbuntuCore"
(updated by API) |
(updated by API) |
||
| Line 52: | Line 52: | ||
====Set up to use another network interface==== | ====Set up to use another network interface==== | ||
To change the setting of "eth1" you can add a new file similar to eth0's configuration file under the /etc/network/interfaces.d/ directory. | To change the setting of "eth1" you can add a new file similar to eth0's configuration file under the /etc/network/interfaces.d/ directory. | ||
| + | ===Setup Wi-Fi=== | ||
| + | First, use the following command to check if Network-Manager is installed on your system: | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | which nmcli | ||
| + | </syntaxhighlight> | ||
| + | If you have installed it, refer to this link to connect to WiFi: [[Use NetworkManager to configure network settings]] | ||
| + | By default the WiFi device is "wlan0". You need to create a configuration file under "/etc/network/interfaces.d/" for WiFi: | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | vi /etc/network/interfaces.d/wlan0 | ||
| + | </syntaxhighlight> | ||
| + | Here is a sample wlan0 file: | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | auto lo | ||
| + | iface lo inet loopback | ||
| + | auto wlan0 | ||
| + | iface wlan0 inet dhcp | ||
| + | wpa-driver wext | ||
| + | wpa-ssid YourWiFiESSID | ||
| + | wpa-ap-scan 1 | ||
| + | wpa-proto RSN | ||
| + | wpa-pairwise CCMP | ||
| + | wpa-group CCMP | ||
| + | wpa-key-mgmt WPA-PSK | ||
| + | wpa-psk YourWiFiPassword | ||
| + | </syntaxhighlight> | ||
| + | Please replace "YourWiFiESSID" and "YourWiFiPassword" with your WiFiESSID and password. After save and close the file you can connect to your WiFi source by running the following command: | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | sudo systemctl daemon-reload | ||
| + | sudo systemctl restart networking | ||
| + | </syntaxhighlight> | ||
| + | After you power on your board it will automatically connect to your WiFi source.<br /> | ||
| + | Please note that if you use one TF card to boot multiple boards the WiFi device name will likely be named to "wlan1", "wlan2" and etc. You can reset it to "wlan0" by deleting the contents of the following file and reboot your board: | ||
| + | /etc/udev/rules.d/70-persistent-net.rules | ||
===Install the kernel-header package=== | ===Install the kernel-header package=== | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| Line 132: | Line 165: | ||
| #default = | | #default = | ||
}} | }} | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Revision as of 06:15, 7 January 2023
Contents
1 Work with FriendlyCore
1.1 FriendlyCore User Account
- Non-root User:
User Name: pi Password: pi
- Root:
User Name: root Password: fa
1.2 Update Software Packages
$ sudo apt-get update
1.3 Setup Network Configurations
1.3.1 Set static IP address
By default "eth0" is assigned an IP address obtained via dhcp. If you want to change the setting you need to change the following file:
vi /etc/network/interfaces.d/eth0
For example if you want to assign a static IP to it you can run the following commands:
auto eth0
iface eth0 inet static
address 192.168.1.231
netmask 255.255.255.0
gateway 192.168.1.11.3.2 Set a DNS
You also need to modify the following file to add the DNS configuration:
vi /etc/systemd/resolved.conf
For example, set to 192.168.1.1:
[Resolve] DNS=192.168.1.1
Restart the systemd-resolved service with the following command:
sudo systemctl restart systemd-resolved.service sudo systemctl enable systemd-resolved.service
1.3.3 Set up to use another network interface
To change the setting of "eth1" you can add a new file similar to eth0's configuration file under the /etc/network/interfaces.d/ directory.
1.4 Setup Wi-Fi
First, use the following command to check if Network-Manager is installed on your system:
which nmcliIf you have installed it, refer to this link to connect to WiFi: Use NetworkManager to configure network settings By default the WiFi device is "wlan0". You need to create a configuration file under "/etc/network/interfaces.d/" for WiFi:
vi /etc/network/interfaces.d/wlan0
Here is a sample wlan0 file:
auto lo
iface lo inet loopback
auto wlan0
iface wlan0 inet dhcp
wpa-driver wext
wpa-ssid YourWiFiESSID
wpa-ap-scan 1
wpa-proto RSN
wpa-pairwise CCMP
wpa-group CCMP
wpa-key-mgmt WPA-PSK
wpa-psk YourWiFiPasswordPlease replace "YourWiFiESSID" and "YourWiFiPassword" with your WiFiESSID and password. After save and close the file you can connect to your WiFi source by running the following command:
sudo systemctl daemon-reload sudo systemctl restart networking
After you power on your board it will automatically connect to your WiFi source.
Please note that if you use one TF card to boot multiple boards the WiFi device name will likely be named to "wlan1", "wlan2" and etc. You can reset it to "wlan0" by deleting the contents of the following file and reboot your board:
/etc/udev/rules.d/70-persistent-net.rules
1.5 Install the kernel-header package
sudo dpkg -i /opt/linux-headers-*.deb
