Difference between revisions of "NanoPi R4S/zh"
From FriendlyELEC WiKi
(→Link to Rockchip Resources) |
|||
Line 83: | Line 83: | ||
==Link to Rockchip Resources== | ==Link to Rockchip Resources== | ||
− | {{ | + | {{Link_to_RK3399_datasheet}} |
==Schematic, PCB CAD File== | ==Schematic, PCB CAD File== | ||
*Schematic: [https://wiki.friendlyarm.com/wiki/images/0/06/NanoPi-R4S-1GB-2008-Schematic.pdf NanoPi-R4S-1GB-2008-Schematic.pdf] [https://wiki.friendlyarm.com/wiki/images/c/c2/NanoPi-R4S-4GB-2008-Schematic.pdf NanoPi-R4S-4GB-2008-Schematic.pdf] | *Schematic: [https://wiki.friendlyarm.com/wiki/images/0/06/NanoPi-R4S-1GB-2008-Schematic.pdf NanoPi-R4S-1GB-2008-Schematic.pdf] [https://wiki.friendlyarm.com/wiki/images/c/c2/NanoPi-R4S-4GB-2008-Schematic.pdf NanoPi-R4S-4GB-2008-Schematic.pdf] | ||
*PCB CAD File:[https://wiki.friendlyarm.com/wiki/images/a/ab/NanoPi_R4S_1GB_2008_dxf.zip NanoPi_R4S_1GB_2008_dxf.zip] [https://wiki.friendlyarm.com/wiki/images/1/18/NanoPi_R4S_4GB_2008_dxf.zip NanoPi_R4S_1GB_2008_dxf.zip] | *PCB CAD File:[https://wiki.friendlyarm.com/wiki/images/a/ab/NanoPi_R4S_1GB_2008_dxf.zip NanoPi_R4S_1GB_2008_dxf.zip] [https://wiki.friendlyarm.com/wiki/images/1/18/NanoPi_R4S_4GB_2008_dxf.zip NanoPi_R4S_1GB_2008_dxf.zip] |
Revision as of 02:50, 2 November 2020
Contents
1 Introduction
File:NanoPi R4S-01B.jpg
Overview
File:NanoPi R4S-A01.jpg
Front
- The NanoPi R4S is a RK3399 SoC based ARM board.
2 Hardware Spec
- SoC: Rockchip RK3399
- CPU: big.LITTLE,Dual-Core Cortex-A72(up to 2.0GHz) + Quad-Core Cortex-A53(up to 1.5GHz)
- GPU: Mali-T864 GPU,supports OpenGL ES1.1/2.0/3.0/3.1, OpenCL, DX11, and AFBC
- VPU: 4K VP9 and 4K 10bits H265/H264 60fps decoding, Dual VOP, etc
- PMU: RK808-D PMIC, cooperated with independent DC/DC, enabling DVFS, software power-down, RTC wake-up, system sleep mode
- RAM: 1GB DDR3/4GB LPDDR4
- Flash: no Onboard eMMC
- Ethernet: one Native Gigabit Ethernet, and one PCIe Gigabit Ethernet
- USB: two USB 3.0 Type-A ports
- Pin header extension interface
- 2x5-pin header: SPI x 1, I2C x 1
- 4-pin header: USB 2.0
- microSD Slot x 1
- Debug: one Debug UART, 3 Pin 2.54mm header, 3V level, 1500000bps
- LEDs: 1 x power LED and 3 x GPIO Controlled LED (SYS, LAN, WAN)
- others:
- 2 Pin 1.27/1.25mm RTC battery input connector
- one UserKey
- one 5V Fan connector
- Power supply: DC 5V/3A, via USB-C connector or Pin header
- PCB: 8 Layer, 66 mm x 66 mm
- Ambient Operating Temperature: -20℃ to 70℃
3 Diagram, Layout and Dimension
3.1 Layout
- 2x5-pin header
Pin# Assignment Pin# Assignment 1 VDD_5V 2 VDD_3.3V 3 VDD_5V 4 I2C3_SDA 5 GND 6 I2C3_SCL 7 SPI1_CLK 8 SPI1_MOSI 9 SPI1_CS 10 SPI1_MISO
- 4-pin header
1 2 3 4 VDD_5V USB_DM USB_DP GND
- Debug UART Pin Spec
- 3V level signals, 1500000bps
Pin# Assignment Description 1 GND 0V 2 UART2DBG_TX output 3 UART2DBG_RX intput
- USB Port
- Each USB 3.0 port has 2A overcurrent protection.
- RTC
- RTC backup current is 27uA.
- Connector P/N: Molex 53398-0271
- Notes
- Power Input : 5V/3A, via USB Type-C(USB PD Specification is not supported) or Pin1&Pin2 of the 2x5-pin header