Difference between revisions of "1-bay NAS Dock"
From FriendlyELEC WiKi
(→特性) |
(→硬件组装步骤) |
||
| Line 20: | Line 20: | ||
[[File:NAS Dock.png | frameless|500px|NAS Dock-01.PCB]] | [[File:NAS Dock.png | frameless|500px|NAS Dock-01.PCB]] | ||
| − | == | + | ==Hardware Setup== |
| − | + | Essentials You Need for a Complete NAS Solution:<br> | |
| − | (1) 1-bay NAS | + | (1) 1-bay NAS Dock;<br> |
| − | (2) | + | (2) Screw set;<br> |
| − | (3) 2. | + | (3) 2.5" HDD hard disk<br> |
| − | (4) | + | (4) NanoPi NEO with heat sink<br> |
| − | [[File:step0.png | frameless|500px| | + | [[File:step0.png | frameless|500px| List]]<br> |
| − | + | Steps to Assemble a NAS Device:<br> | |
| − | (1) | + | (1) Connect a 2.5"SATA hard disk to the dock and mount the disk on the dock with four screws<br> |
| − | [[File:step1.png | frameless|500px| | + | [[File:step1.png | frameless|500px|Step 1]] [[File:step2.png | frameless|500px|Step 2]] <br> |
| − | (2) | + | (2) Connect a NanoPi NEO with pin-headers to the NAS Dock<br> |
| − | [[File:step3.png | frameless|500px| | + | [[File:step3.png | frameless|500px|Step 3]]<br> |
| − | (3) | + | (3) Connect a 12V power to the NAS Dock and all done<br> |
| − | [[File:step4.png | frameless|500px| | + | [[File:step4.png | frameless|500px|Step 4]]<br> |
==软件安装== | ==软件安装== | ||
Revision as of 14:22, 1 April 2017
Contents
1 Introduction
- The 1-bay NAS Dock is an expansion board which can be used to connect an external hard disk to a FriendlyElec’s NanoPi NEO. Together with FriendlyElec's customized aluminum case and NanoPi NEO you can quickly assemble a storage server.
- It uses JM20329 USB2SATA IC and communicates with a NanoPi NEO via USB interface.
- It works with a 2.5" SATA hard disk.
- It uses TI’s DC-DC chipset to convert a 12V input to 5V. It has a power switch for users to turn on/off the device.
- Its dual-color LED can indicate a connected hard disk's status. When the LED is green it means the power is on. When it is red-blinking it means the connected hard disk is reading/writing.Warning: when the status LED is red-blinking do NOT shut down the power or plug/unplug the power.
2 Hardware Spec
- High-speed USB2SATA IC JM20329
- Supply voltage:12V
- Onboard switch
- Dual-color status LED
- USB Host
- Customized aluminum case
- Ready-to-go software system
- PCB dimension(mm): 151 x 89.7
3 Hardware Setup
Essentials You Need for a Complete NAS Solution:
(1) 1-bay NAS Dock;
(2) Screw set;
(3) 2.5" HDD hard disk
(4) NanoPi NEO with heat sink
Steps to Assemble a NAS Device:
(1) Connect a 2.5"SATA hard disk to the dock and mount the disk on the dock with four screws
(2) Connect a NanoPi NEO with pin-headers to the NAS Dock
(3) Connect a 12V power to the NAS Dock and all done
4 软件安装
4.1 制作一张运行OpenMediaVault的TF卡
4.1.1 下载系统固件
首先访问下载地址下载固件文件(officail-ROMs目录)和烧写工具(tools目录)：
使用以下固件： Debian-for-nas-YYYYMMDD.img.zip 预装了OpenMediaVault软件的Debian系统固件 烧写工具： win32diskimager.rar Windows平台下的系统烧写工具，Linux平台下可以用dd命令烧写系统
4.1.2 制作系统TF卡
将固件Debian-for-nas-YYYYMMDD.img.zip和烧写工具win32diskimager.rar分别解压，在Windows下插入TF卡（限4G及以上的卡)，以管理员身份运行 win32diskimager 工具，
在win32diskimager工具的界面上，选择你的TF卡盘符，选择系统固件，点击 Write 按钮烧写即可。
烧写完成后，将制作好TF卡插入NanoPi NEO，使用12V电源给1-Bay NAS供电，
打开1-Bay NAS开关，看到NanoPi NEO上的蓝色LED闪烁，这说明系统已经开始启动了。
4.2 OpenMediaVault 的使用
test