Difference between revisions of "Matrix - Ultrasonic Ranger"

From FriendlyELEC WiKi
Jump to: navigation, search
(→‎硬件连接)
Line 29: Line 29:
 
[[File:Ultrasonic Ranger.png|thumb|matrix Ultrasonic Ranger]]
 
[[File:Ultrasonic Ranger.png|thumb|matrix Ultrasonic Ranger]]
  
−
==硬件连接==
+
==Applications==
−
===连接NanoPi M1===
+
===Connect to NanoPi M1===
−
参考下图连接模块：<br>
+
Refer to the following connection diagram to connect the module to the NanoPi M1:<br>
 
[[File:Matrix-Ultrasonic_Ranger_nanopi_m1.jpg|frameless|600px|Matrix-Ultrasonic_Ranger_nanopi_m1]]
 
[[File:Matrix-Ultrasonic_Ranger_nanopi_m1.jpg|frameless|600px|Matrix-Ultrasonic_Ranger_nanopi_m1]]
  
−
连接说明：
+
Connection Details:
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
Line 46: Line 46:
 
|}
 
|}
  
−
===连接NanoPi 2===
+
===Connect to NanoPi 2===
−
参考下图连接模块：<br>
+
Refer to the following connection diagram to connect the module to the NanoPi 2:<br>
 
[[File:Matrix-Ultrasonic_Ranger_nanopi_2.jpg|frameless|600px|Matrix-Ultrasonic_Ranger_nanopi_2]]
 
[[File:Matrix-Ultrasonic_Ranger_nanopi_2.jpg|frameless|600px|Matrix-Ultrasonic_Ranger_nanopi_2]]
  
−
连接说明：
+
Connection Details:
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
Line 62: Line 62:
 
|}
 
|}
  
−
===连接NanoPi M2 / NanoPi 2 Fire===
+
===Connect to NanoPi M2 / NanoPi 2 Fire===
−
NanoPi M2和NanoPi 2 Fire的40 Pin引脚定义是一模一样的，所以它们操作Matrix配件的步骤是一样的，这里仅以NanoPi M2为例。<br>
+
Refer to the following connection diagram to connect the module to the NanoPi M2/ NanoPi 2 Fire:<br>
−
参考下图连接模块：<br>
+
 
[[File:Matrix-Ultrasonic_Ranger_nanopi_m2.jpg|frameless|600px|Matrix-Ultrasonic_Ranger_nanopi_m2]]
 
[[File:Matrix-Ultrasonic_Ranger_nanopi_m2.jpg|frameless|600px|Matrix-Ultrasonic_Ranger_nanopi_m2]]
  
−
连接说明：
+
Connection Details:
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
Line 79: Line 78:
 
|}
 
|}
  
−
===连接NanoPC-T2===
+
===Connect to NanoPC-T2===
−
参考下图连接模块：<br>
+
Refer to the following connection diagram to connect the module to the NanoPC-T2:<br>
 
[[File:Matrix-Ultrasonic_Ranger_NanoPC-T2.jpg|frameless|600px|Matrix-Ultrasonic_Ranger_NanoPC-T2]]
 
[[File:Matrix-Ultrasonic_Ranger_NanoPC-T2.jpg|frameless|600px|Matrix-Ultrasonic_Ranger_NanoPC-T2]]
  
−
连接说明：
+
Connection Details:
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-

Revision as of 13:44, 28 June 2016

查看中文

1 Introduction

Ultrasonic Ranger01
  • The Matrix-Ultrasonic_Ranger is used to measure the distance.
  • The module's sensor emits a sound wave, which bounces off a reflective surface and returns to the sensor. Then, using the amount of time it takes for the wave to return to the sensor, the distance to the object can be computed.

2 Features

  • 5V Power
  • Range: 5 cm - 300 cm，Accuracy: 1 cm
  • One wire gpio
  • PCB Dimension (mm): 20 x 40

超声波PCB

  • Pin Description:
Pin Description
S GPIO
V Supply Voltage 5V
G Ground

3 Basic Device Operation

  • The sensor emits a 40kHz, 6 mm sound wave, which bounces off a reflective surface and returns to the sensor. The receiver converts ultrasound waves to electrical signals in mV.
  • The master sends a signal to the module starting to emit a sound wave. After the module receives the returned signal it will will generate a high level indicating the elapsed time and the distance will be calculated by distance = (elapsed time * speed of sound)/2.
matrix Ultrasonic Ranger

4 Applications

4.1 Connect to NanoPi M1

Refer to the following connection diagram to connect the module to the NanoPi M1:
Matrix-Ultrasonic_Ranger_nanopi_m1

Connection Details:

Matrix-Ultrasonic_Ranger NanoPi M1
S Pin7
V Pin4
G Pin6

4.2 Connect to NanoPi 2

Refer to the following connection diagram to connect the module to the NanoPi 2:
Matrix-Ultrasonic_Ranger_nanopi_2

Connection Details:

Matrix-Ultrasonic_Ranger NanoPi 2
S Pin7
V Pin4
G Pin6

4.3 Connect to NanoPi M2 / NanoPi 2 Fire

Refer to the following connection diagram to connect the module to the NanoPi M2/ NanoPi 2 Fire:
Matrix-Ultrasonic_Ranger_nanopi_m2

Connection Details:

Matrix-Ultrasonic_Ranger NanoPi M2
S Pin7
V Pin4
G Pin6

4.4 Connect to NanoPC-T2

Refer to the following connection diagram to connect the module to the NanoPC-T2:
Matrix-Ultrasonic_Ranger_NanoPC-T2

Connection Details:

Matrix-Ultrasonic_Ranger NanoPC-T2
S Pin15
V Pin29
G Pin30

5 编译运行测试程序

启动开发板并运行Debian系统，进入系统后克隆Matrix代码仓库： 

$ apt-get update && apt-get install git
$ git clone https://github.com/friendlyarm/matrix.git

克隆完成后会得到一个名为matrix的目录。

编译并安装Matrix： 

$ cd matrix
$ make && make install

运行测试程序： 

$ matrix-ultrasonic_ranger

注意：此模块并不支持热插拔，启动系统前需要确保硬件连接正确。
运行效果如下：

The distance is  24 cm

将超模波模块的正面对准待测距物体，测距完毕后程序会打印距离值。

6 代码说明

所有的开发板都共用一套Matrix代码，本模块的测试示例代码为matrix-ultrasonic_ranger，内容如下: 

int main(int argc, char ** argv)
{
    int distance = -1;
    int pin = GPIO_PIN(7);
    int board;
 
    if ((board = boardInit()) < 0) {
        printf("Fail to init board\n");
        return -1;
    }
    if (board == BOARD_NANOPI_T2)
        pin = GPIO_PIN(15);
 
    system("modprobe "DRIVER_MODULE);
    if (Hcsr04Init(pin) == -1) {
        printf("Fail to init hcsr04\n");
        goto err;
    }
    if (Hcsr04Read(&distance) != -1) {
        printf("The distance is %3d cm\n", distance);
    } else {
        printf("Faid to get distance\n");
    }
    Hcsr04DeInit();
err:
    system("rmmod "DRIVER_MODULE);
 
    return 0;
}

API说明参考维基：Matrix API reference manual

7 Resources

8 Update Log

8.1 Feb-23-2016

  • Added the description for "NanoPi 2 branch" in Section 4
  • Added Section 5: Connect to NanoPi 2


Retrieved from "https://wiki.friendlyelec.com/wiki/index.php?title=Matrix_-_Ultrasonic_Ranger&oldid=6305"