Difference between revisions of "Matrix - 2'8 SPI Key TFT"
From FriendlyELEC WiKi
(→Compile & Run Test Program) |
|||
| Line 99: | Line 99: | ||
Please refer to the following connection diagram to connect the module to the NanoPi M2 / P2:<br> | Please refer to the following connection diagram to connect the module to the NanoPi M2 / P2:<br> | ||
[[File:Matrix-2'8_SPI_Key_TFT_nanopi_m2.jpg|frameless|600px|Matrix-2'8_SPI_Key_TFT_nanopi_m2]] | [[File:Matrix-2'8_SPI_Key_TFT_nanopi_m2.jpg|frameless|600px|Matrix-2'8_SPI_Key_TFT_nanopi_m2]] | ||
| − | |||
==Compile & Run Test Program== | ==Compile & Run Test Program== | ||
| Line 117: | Line 116: | ||
The nanopi-status is a small Qt utility which can be used to list system's basic information. Here is what you should expect to observe:<br> | The nanopi-status is a small Qt utility which can be used to list system's basic information. Here is what you should expect to observe:<br> | ||
[[File:st7789s-status.png|frameless|600px|st7789s-status]] | [[File:st7789s-status.png|frameless|600px|st7789s-status]] | ||
| − | |||
| − | |||
<!--- | <!--- | ||
| Line 182: | Line 179: | ||
---> | ---> | ||
| + | <!--- | ||
==Connect to NanoPi== | ==Connect to NanoPi== | ||
===Preparations=== | ===Preparations=== | ||
| Line 239: | Line 237: | ||
==Connect to Arduino== | ==Connect to Arduino== | ||
| + | ---> | ||
==Resources== | ==Resources== | ||
Revision as of 15:48, 16 June 2016
Contents
1 Introduction
- Matrix-2'8_SPI_Key_TFT模块是一款2.8英寸的TFT 触摸LCD，模块采用ST7789S驱动IC和XPT2046电阻式触摸IC，屏幕分辨率为320*240，采用SPI控制接口，模块还包含3个独立按键，可根据需要自定义功能。
- 详细规格如下所示：
| LCD尺寸 | 2.8寸 |
| 显示区域 | 57.6mm*43.2mm |
| 驱动IC | ST7789S |
| 分辨率 | 320*240（RGB） |
| 接口方式 | SPI |
| 工作电压 | 5V |
| 背光电压 | 5V |
| 触摸屏类型 | 电阻式，钢化玻璃触摸屏 |
模块上电默认打开背光，可通过置低LED_EN引脚关闭背光。如果需要关闭上电打开背光，只需要拿到电路板上的R12电阻，再通过置高LED_EN引脚打开背光；
2 Features
- PCB dimension(mm):
- Pin Description:
| Pin | Description | Pin | Description |
| 1 | VDD_3.3V | 2 | VDD_5V |
| 3 | NC | 4 | VDD_5V |
| 5 | NC | 6 | GND |
| 7 | LCD_RESET | 8 | NC |
| 9 | GND | 10 | NC |
| 11 | LED_EN | 12 | NC |
| 13 | KEY_1 | 14 | GND |
| 15 | KEY_2 | 16 | KEY_3 |
| 17 | VDD_3.3V | 18 | T_IRQ |
| 19 | SPI_MOSI | 20 | GND |
| 21 | SPI_MISO | 22 | LCD_D/C |
| 23 | SPI_CLK | 24 | LCD_CS |
| 25 | GND | 26 | T_CS |
3 Applications
3.1 Connect to NanoPi M1
Please refer to the following connection diagram to connect the module to the NanoPi M1:
3.2 Connect to NanoPi 2
Please refer to the following connection diagram to connect the module to the NanoPi 2:
3.3 Connect to NanoPi M2 / NanoPi 2 Fire
Please refer to the following connection diagram to connect the module to the NanoPi M2 / P2:
Matrix-2'8_SPI_Key_TFT_nanopi_m2
4 Compile & Run Test Program
Boot your ARM board with Debian and copy the matrix code:
$ apt-get update && apt-get install git $ git clone https://github.com/friendlyarm/matrix.git
If your cloning is done successfully a "matrix" directory will be generated.
Compile and install Matrix:
cd matrix/demo/nanopi-status ./build.sh ./run.sh /dev/fb-st7789s
The nanopi-status is a small Qt utility which can be used to list system's basic information. Here is what you should expect to observe:
5 Resources
6 Update Log
6.1 Feb-24-2016
- Added the driver's source code location in Section 5.2
