Difference between revisions of "NanoPi M1"

Revision as of 10:25, 1 April 2016

查看中文

1 Introduction

Overview

Front

Back

frameless

• The NanoPi M1 is an Allwinner H3 based ARM board designed and released by FriendlyARM for hobbyists, makers and electronic fans. It is only two thirds the size of the Raspberry Pi. It is open source. It works with Ubuntu MATE, Debian and etc.
• The NanoPi M1 uses the Allwinner H3 Soc. It integrates Ethernet, IR receiver, video/audio output and supports HDMI and AVOUT. It can be powered via the MicroUSB port
• In such a small board it still integrates rich interfaces and ports. Besides the popular HDMI, Ethernet, USB-Host, USB-OTG, DVP camera interface and AVOUT (audio and video) it has an onboard Microphone, IR receiver, a serial debug port and a Raspberry Pi compatible 40 pin GPIO pin header.

2 Features

• CPU: Allwinner H3, Quad-core Cortex-A7@1.2GHz
• GPU: Mali400MP2@600MHz，Supports OpenGL ES2.0
• DDR3 RAM: 512MB
• Connectivity: 10/100M Ethernet
• Audio: 3.5mm audio jack/Via HDMI
• Microphone: Onboard microphone
• IR Receiver: Onboard IR receiver
• USB Host：Type A, USB 2.0 x 3
• MicroSD Slot x 1
• MicroUSB: for data transmission and power input, OTG
• Video Output: HDMI 1.4 1080P, CVBS
• DVP Camera Interface: 24pin, 0.5mm pitch FPC seat
• Debug Serial Port: 4Pin, 2.54mm pitch pin header
• GPIO: 2.54mm spacing 40pin, compatible with Raspberry Pi's GPIO. It includes UART, SPI, I2C, IO etc
• User Key: Power LED x 1, Reset x 1
• PC Size: 64 x 50mm
• Power Supply: DC 5V/2A
• OS/Software: u-boot，Ubuntu MATE，Debian

3 Diagram, Layout and Dimension

3.1 Layout

NanoPi M1 Layout

• GPIO Pin Spec

Pin#	Name	Pin#	Name
1	SYS_3.3V	2	VDD_5V
3	I2C0_SDA	4	VDD_5V
5	I2C0_SCL	6	GND
7	GPIOG11	8	UART1_TX/GPIOG6
9	GND	10	UART1_RX/GPIOG7
11	UART2_TX/GPIOA0	12	PWM1/GPIOA6
13	UART2_RTS/GPIOA2	14	GND
15	UART2_CTS/GPIOA3	16	UART1_RTS/GPIOG8
17	SYS_3.3V	18	UART1_CTS/GPIOG9
19	SPI0_MOSI/GPIOC0	20	GND
21	SIP0_MISO/GPIOC1	22	UART2_RX/GPIOA1
23	SPI0_CLK/GPIOC29	24	SPI0_CS/GPIOC3
25	GND	26	SPDIF-OUT/GPIOA17
27	I2C1_SDA/GPIOA19	28	I2C1_SCL/GPIOA18
29	GPIOA20	30	GND
31	GGPIOA21	32	GPIOA7
33	GPIOA8	34	GND
35	UART3_CTS/SPI1_MISO/GPIOA16	36	UART3_TX/SPI1_CS/GPIOA13
37	GPIOA9	38	UART3_RTS/SPI1_MOSI/GPIOA15
39	GND	40	UART3_RX/SPI1_CLK/GPIOA14

• Debug Port（UART0）

Pin#	Name
1	GND
2	VDD_5V
3	UART_TXD0
4	UART_RXD0

• DVP Camera IF Pin Spec

Pin#	Name	Description
1, 2	SYS_3.3V	3.3V power output, to camera modules
7,9,13,15,24	GND	Gound, 0V
3	I2C2_SCL	I2C Clock Signal
4	I2C2_SDA	I2C Data Signal
5	GPIOE15	Regular GPIO, control signals output to camera modules
6	GPIOE14	Regular GPIO, control signals output to camera modules
8	MCLK	Clock signals output to camera modules
10	NC	Not Connected
11	VSYNC	vertical synchronization to CPU　from camera modules
12	HREF/HSYNC	HREF/HSYNC signal to CPU from camera modules
14	PCLK	PCLK signal to CPU from camera modules
16-23	Data bit7-0	data signals

Note:

1. SYS_3.3V: 3.3V power output
2. VDD_5V: 5V power input/output. When the external device’s power is greater than the MicroUSB’s the external device is charging the board otherwise the board powers the external device. The input range is 4.7V ~ 5.6V
3. All pins are 3.3V and output current is 5mA. It can drive small loads. No IO pins can drive a load.
4. For more details refer to the document: NanoPi-M1-1603-Schematic.pdf

3.2 Board Dimension

For more details please refer to: pcb file in dxf

4 Get Started

4.1 Essentials You Need

Before starting to use your NanoPi M1 get the following items ready

• NanoPi M1
• microSD Card/TFCard: Class 10 or Above, minimum 8GB SDHC
• microUSB power. A 5V/2A power is a must
• HDMI monitor
• USB keyboard and mouse
• A host computer running Ubuntu 14.04 64 bit system

4.2 TF Cards We Tested

To make your NanoPi M1 boot and run fast we highly recommand you use a Class10 8GB SDHC TF card or a better one. The following cards are what we used in all our test cases presented here:

• SanDisk TF 8G Class10 Micro/SD TF card:

• SanDisk TF128G MicroSDXC TF 128G Class10 48MB/S:

• 川宇 8G C10 High Speed class10 micro SD card:

4.3 Make an Installation TF Card

4.3.1 Under Windows

Get the following files from here:[http://wiki.friendlyarm.com/wiki/nanopim1/download/ to download image files.

Image Files
nanopi-m1-debian-sd4g.img.zip	Debian Image Files
Flash Utility:
win32diskimager.rar	Windows utility. Under Linux users can use "dd"

• Uncompress these files. Insert a TF card(at least 4G) into a Windows PC and run the win32diskimager utility as administrator. On the utility's main window select your TF card's drive, the wanted image file and click on "write" to start flashing the TF card.
• Insert this card into your NanoPi M1 and power on (with a 5V/2A power source). If the green LED is on and the blue LED is blinking this indicates your NanoPi M1 has successfully booted.
  

5 Working with Debian

5.1 Extend TF Card's rootfs Section

We strongly recommend you to do this right after you have made an installation TF card since this will greatly enhance your M1's experience.
Insert your TF card into a host PC and run the following commands on your PC's terminal:

sudo umount /dev/sdx?
sudo parted /dev/sdx unit % resizepart 2 100 unit MB print
sudo resize2fs -f /dev/sdx2

Note: you need to replace "/dev/sdx" with the device name in your system

5.2 Run Debian

• Insert a TF card with Debian image files into your NanoPi M1, connect the NanoPi M1 to an HDMI monitor and a 5V/2A power source the NanoPi M1 will be automatically powered on. If you can see the blue LED flashing it means your board is working and you will see Debain being loaded on the HDMI monitor.
  

1）If you connect the NanoPi M1 to an HDMI monitor you need to use a USB mouse and a USB keyboard to operate.
2) If you want to do kernel development you need to use a serial communication board, ie a PSU-ONECOM board, which will allow you to operate the board via a serial terminal.

• Here is a setup where we connect a NanoPi M1 to a PC via the PSU-ONECOM and you can power on your M1 from either the PSU-ONECOM or M1's MicroUSB:

• The password for "root" is "fa".

5.3 Ethernet Connection

If the NanoPi M1 is connected to a network via Ethernet before it is powered on it will automatically obtain an IP after it is powered up. If it is not connected via Ethernet or its DHCP is not activated obtaining an IP will fail and system will hang on for about 15 to 60 seconds

• 1) Setup MAC Address

The NanoPi M1 by default doesn't have a valid MAC address. If the board connects a network successfully it will automatically generates a random MAC in "/etc/network/interfaces.d/eth0". Users can change it to a self-defined valid one:

vi /etc/network/interfaces.d/eth0

Here is the content of a sample configuration file:

auto eth0
allow-hotplug eth0
iface eth0 inet dhcp
hwaddress 76:92:d4:85:f3:0f

The "hwaddress" specifies the MAC address. Here the "76:92:d4:85:f3:0f" is a random MAC. We suggest users change it to a valid one.
Note: when you reset the MAC please make sure your MAC meets IEEE's definition otherwise it will cause unexpected issues. After you make your change, save, exit and reboot your board or run the following commands to restart the network:

systemctl restart networking

5.4 Login to Debian via VNC and SSH

If your NanoPi M1 is not connected to a display device you can login to your NanoPi M1 from a mobile phone. You need to download and install a "VNC Viewer" from here on a mobile phone and login to the NanoPi M1 via VNC. Its default password is "fa123456".
Here is a screenshot which shows how it looks like when users login to the NanoPi M1 from an iPhone via VNC:

You can login via "SSH -l root 192.168.8.1" and the default password for "root" is "fa". You need to replace "192.168.8.1" with your actual IP address.

5.5 HDMI Resolution

Our Debian system's HDMI resolution is set by a script.bin file in the root directory of the installation TF card's boot section. By default the resolution is 1080P60. There are multiple script.bin files under that directory for different resolutions. For example if you want to modify the resolution to 720P60 you can use the script-720p-60.bin file to replace the existing one by using the following command:

# in TF card boot partition
cp script/script-720p-60.bin ./script.bin

5.6 HDMI Audio Output

Our Debian system's default audio output is the 3.5mm audio jack. You can turn on the HDMI audio by editting the /etc/asound.conf file:

pcm.!default {
    type hw
    card 1
    device 0
}
 
ctl.!default {
    type hw
    card 1
}

card 0 points to the 3.5mm audio jack and card 1 points to the HDMI audio. You need to save your changes and reboot your system to make your changes take effect.

5.7 Test GPU

After Debian loads please login from a terminal and run "glmark2-es2":

glmark2-es2

5.8 Test VPU

Visit this link download link to download files
After Debian is loaded login from a terminal and run "mplayer":

mplayer -vo vdpau -vc ffmpeg12vdpau,ffh264vdpau, ./big_buck_bunny_1080p_H264_AAC_25fps_7200K.MP4

In our test it could play 1080P video fluently.

6 Make Your Own Debian

Visit this link download to get the source code, uncompress it and a lihee directory will be generated. Or you can get it from our github:

git clone https://github.com/friendlyarm/h3_lichee.git lichee

After you get the source code enter the lichee directory:

cd lichee

6.1 Compile Source Code

Compile the whole source code packages including U-boot, Linux Kernel and Modules:

./build.sh -p sun8iw7p1 -b nanopi-h3
./gen_script.sh

The gen_script.sh script contains all the necessary files to compile all of these files. After it is executed multiple script.bin files will be generated for different display resolutions. A script.bin file is a configuration file made by Allwinnner for its CPU series. For more details refer to script.bin

6.2 Flash Image to TF Card

Run the following command to flash U-boot, Linux Kernel and script.bin to your TF card:

./burn_into_sd.sh /dev/sdx

Note: you need to replace "/dev/sdx" with the device name in your system. This script flashes U-Boot to your TF card and copies uImage and script.bin to your TF card's boot section.

6.3 Compile U-boot

./build.sh -p sun8iw7p1 -b nanopi-h3 -m uboot

After a u-boot executable is generated some extra patches need to be patched to it. Run "./gen_script.sh" to patch this executable.
If you want to manually patch the executable refer to H3_Manual_build_howto

6.4 Compile Linux Kernel

./build.sh -p sun8iw7p1 -b nanopi-h3 -m kernel

After the compilation is done a uImage and its kernel modules will be generated under "linux-3.4/output".

6.5 Clean Source Code

./build.sh -p sun8iw7p1 -b nanopi-h3 -m clean

7 Make Your Own Android

8 More OS Support

8.1 Ubuntu-Core

Ubuntu-Core is a basic verson which has support for Ethernet and SSH.
FriendlyARM doesn't provide technical support for it.

• Go to this link download link to download the image files
• Uncompress it and flash the image file to a TF card with win32diskimager under Windows
• After it is done you can boot your NanoPi M1 with this card
• Login name: "root" or "fa", Password: fa

8.2 Ubuntu-MATE

Ubuntu-Mate is a Ubuntu variant and its GUI is Mate-desktop. You can login via SSH when you connect a NanoPi M1 to an HDMI
FriendlyARM doesn't provide technical support for it

• Go to this link download link to download the image files
• Uncompress it and flash the image file to a TF card with win32diskimager under Windows
• After it is done you can boot your NanoPi M1 with this card
• Login name: "root" or "fa", Password: fa

9 Resources

• Schematic NanoPi-M1-1603-Schematic.pdf
• Dimensional Diagram pcb file in dxf
• Allwinner H3 datasheet Allwinner_H3_Datasheet_V1.2.pdf

10 Update Log

10.1 March-22-2016

• Released English Version

10.2 March-29-2016

• Corrected expression errors