Difference between revisions of "Matrix - USB WiFi"
From FriendlyELEC WiKi
| Line 1: | Line 1: | ||
[[Matrix - USB WiFi/zh|查看中文]] | [[Matrix - USB WiFi/zh|查看中文]] | ||
| − | == | + | ==Introduction== |
| − | * | + | * Note: the following method applies to NanoPi M2 too。 |
NanoPi 2 Fire使用的固件跟NanoPi 2通用，为了不跟NanoPi 2的SD WiFi产生冲突，内核缺省不编译USB WiFi。如果需要给NanoPi 2 Fire使用USB WiFi，可单独把USB WiFi编译进内核。<br> | NanoPi 2 Fire使用的固件跟NanoPi 2通用，为了不跟NanoPi 2的SD WiFi产生冲突，内核缺省不编译USB WiFi。如果需要给NanoPi 2 Fire使用USB WiFi，可单独把USB WiFi编译进内核。<br> | ||
由于市面上USB WiFi型号多达上百种，如果把全部USB WiFi驱动选上不太现实，所以这里只介绍一种的方法，其他USB WiFi型号 方法一样，可参看此处自行编译支持。 | 由于市面上USB WiFi型号多达上百种，如果把全部USB WiFi驱动选上不太现实，所以这里只介绍一种的方法，其他USB WiFi型号 方法一样，可参看此处自行编译支持。 | ||
| Line 11: | Line 11: | ||
* 开始之前，需要先根据NanoPi 2 Fire的wiki：[[NanoPi_2_Fire/zh|NanoPi_2_Fire]]，把启动卡做好。 | * 开始之前，需要先根据NanoPi 2 Fire的wiki：[[NanoPi_2_Fire/zh|NanoPi_2_Fire]]，把启动卡做好。 | ||
| − | == | + | ==Download Kernel Source Code== |
| − | + | Please download the NanoPi 2 Fire's kernel source code:<br> | |
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
git clone https://github.com/friendlyarm/linux-3.4.y.git | git clone https://github.com/friendlyarm/linux-3.4.y.git | ||
| Line 19: | Line 19: | ||
git checkout nanopi2-lollipop-mr1 | git checkout nanopi2-lollipop-mr1 | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | NanoPi 2 | + | The NanoPi 2 Fire's kernel source code lies in the "nanopi2-lollipop-mr1" branch<br> |
| − | == | + | ==Add USB WiFi in Menuconfig== |
| − | + | Add the WIFI support in the kernel and compile | |
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
touch .scmversion | touch .scmversion | ||
| Line 39: | Line 39: | ||
make uImage | make uImage | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| − | + | After your compilation succeeds a uImage will be generated in the "arch/arm/boot/uImage" directory. You can use it to replace the existing uImage.hdmi.<br> | |
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
sync | sync | ||
Revision as of 10:50, 9 March 2016
Contents
1 Introduction
- Note: the following method applies to NanoPi M2 too。
NanoPi 2 Fire使用的固件跟NanoPi 2通用，为了不跟NanoPi 2的SD WiFi产生冲突，内核缺省不编译USB WiFi。如果需要给NanoPi 2 Fire使用USB WiFi，可单独把USB WiFi编译进内核。
由于市面上USB WiFi型号多达上百种，如果把全部USB WiFi驱动选上不太现实，所以这里只介绍一种的方法，其他USB WiFi型号 方法一样，可参看此处自行编译支持。
- 示例USB WiFi芯片：RT3070；
- 无线标准： - IEEE 802.11b/g/n；
- 操作系统：Debian；
- 开始之前，需要先根据NanoPi 2 Fire的wiki：NanoPi_2_Fire，把启动卡做好。
2 Download Kernel Source Code
Please download the NanoPi 2 Fire's kernel source code:
git clone https://github.com/friendlyarm/linux-3.4.y.git cd linux-3.4.y git checkout nanopi2-lollipop-mr1
The NanoPi 2 Fire's kernel source code lies in the "nanopi2-lollipop-mr1" branch
3 Add USB WiFi in Menuconfig
Add the WIFI support in the kernel and compile
touch .scmversion make nanopi2_linux_defconfig make menuconfig [*] Networking support --> -*- Wireless --> [*] Generic IEEE 802.11 Networking Stack (mac80211) Device Drivers --> [*] Network device support --> [*] Wireless LAN --> [*] Ralink driver support --> [*] Ralink rt27xx/rt28xx/rt30xx (USB) support [*] rt2800usb - Include support for rt33xx devices [*] rt2800usb - Include support for rt35xx devices make uImage
After your compilation succeeds a uImage will be generated in the "arch/arm/boot/uImage" directory. You can use it to replace the existing uImage.hdmi.
sync如果要编译支持LCD显示的内核，则需要在此基础上修改内核配置：
touch .scmversion make menuconfig Device Drivers --> Graphics support --> Nexell Graphics --> [*] LCD [ ] HDMI mak uImage
启用LCD，同时取消HDMI，然后退出并保存配置，编译后即可获得支持LCD显示的uImage，用于替换SD卡boot分区下的uImage。
4 下载linux-firmware
将SD卡插入开发板，并接上网线，然后上电，执行以下步骤安装RT3070的固件：
apt-get update apt-get install firmware-ralink
如果你使用的USB WiFi不是RT3070，你可以尝试安装所有固件即可：
apt-get install firmware-*
安装成功后，接上USB WiFi，板子即能识别到USB WiFi。
