Difference between revisions of "Matrix - Ultrasonic Ranger"

Revision as of 09:12, 23 February 2016

查看中文

1 Introduction

Ultrasonic Ranger01

The Matrix-Ultrasonic_Ranger is used to measure the distance.
The module's sensor emits a sound wave, which bounces off a reflective surface and returns to the sensor. Then, using the amount of time it takes for the wave to return to the sensor, the distance to the object can be computed.

2 Features

5V Power
Range: 5 cm - 300 cm，Accuracy: 1 cm
One wire gpio
PCB Dimension (mm): 20 x 40

Pin Description:

Pin	Description
S	GPIO
V	Supply Voltage 5V
G	Ground

3 Basic Device Operation

The sensor emits a 40kHz, 6 mm sound wave, which bounces off a reflective surface and returns to the sensor. The receiver converts ultrasound waves to electrical signals in mV.
The master sends a signal to the module starting to emit a sound wave. After the module receives the returned signal it will will generate a high level indicating the elapsed time and the distance will be calculated by distance = (elapsed time * speed of sound)/2.

matrix Ultrasonic Ranger

4 Download Matrix Source Code

All the matrix modules' code samples are open source. They are maintained on GitHub - https://github.com/friendlyarm/matrix.git
Each branch in this hub contains the matrix modules' code samples for a board that the matrix modules can work with.

The nanopi branch contains the matrix modules' code samples for the NanoPi
The nanopi 2 branch contains the matrix modules' code samples for the NanoPi 2
The tiny4412 branch contains the matrix modules' code samples for the Tiny4412
The raspberrypi branch contains the matrix modules' code samples for the RaspberryPi

Please follow the steps below to get the source code:
Install the git utility on a PC running Ubuntu14.04

$ sudo apt-get install git

Clone the matrix code from GitHub

$ git clone https://github.com/friendlyarm/matrix.git

If this is successful a "matrix" directory will be generated, which will contain all the matrix modules' code samples.

5 Connect to NanoPi 2

5.1 Hardware Connection

Please refer to the following connection diagram to connect the Matrix-Ultrasonic_Ranger to the NanoPi 2:

Connection Details:

Matrix-Ultrasonic_Ranger	NanoPi 2
S	Pin7
V	Pin4
G	Pin6

5.2 编译测试程序

进入Matrix代码仓库，切换到nanopi2分支

$ cd matrix
$ git checkout nanopi2

编译Matrix配件代码

$ make CROSS_COMPILE=arm-linux- clean
$ make CROSS_COMPILE=arm-linux-
$ make CROSS_COMPILE=arm-linux- install

注意：请确保你的主机PC当前使用的交叉编译器为NanoPi 2配套的arm-linux-gcc-4.9.3。
编译成功后库文件位于install/lib目录下，而测试程序则位于install/usr/bin目录下，模块Matrix-Ultrasonic_Ranger对应的测试程序为matrix-ultrasonic_ranger。
硬件驱动模块位于modules目录下，对应的驱动源码都包含在在NanoPi 2的Linux内核仓库里：https://github.com/friendlyarm/linux-3.4.y.git

5.3 运行测试程序

将带有Debian系统的SD卡插入一台运行Linux的电脑，可以挂载SD卡上的boot和rootfs分区。
假设rootfs分区的挂载路径为/media/rootfs，执行以下命令将Matrix的硬件驱动、库文件和测试程序拷贝到NanoPi 2的文件系统上。

$ cp modules /media/rootfs/ -r
$ cp install/lib/* /media/rootfs/lib/ -d
$ cp install/usr/bin/* /media/rootfs/usr/bin/

将SD卡重新插入NanoPi 2，上电启动，在Debian的shell终端中执行以下命令加载硬件驱动。

$ cd /modules
$ insmod matrix_hcsr04.ko

运行模块Matrix-Ultrasonic_Ranger的测试程序。

$ matrix-ultrasonic_ranger

运行效果如下：

5.4 Code Sample

int main(int argc, char ** argv)
{
    int distance = -1;
    int pin = GPIO_PIN(7);
 
    if (Hcsr04Init(pin) == -1) {
        printf("Fail to init hcsr04\n");
    }
    if (Hcsr04Read(&distance) != -1) {
        printf("Get distance: %3d cm\n", distance);
    } else {
        printf("Faid to get distance\n");
    }
    Hcsr04DeInit();
    return 0;
}

6 Connect to NanoPi

6.1 Preparations

Please install a Debian on a NanoPi and an appropriate cross compiler on a PC. Please refer to wiki: NanoPi
Compile a NanoPi kernel. Note: please use the kernel's source code from the nanopi-v4.1.y-matrix branch.

$ git clone https://github.com/friendlyarm/linux-4.x.y.git
$ cd linux-4.x.y
$ git checkout nanopi-v4.1.y-matrix
$ make nanopi_defconfig
$ touch .scmversion
$ make

6.2 Hardware Connection

Please refer to the following connection diagram to connect the Matrix-Ultrasonic_Ranger to the NanoPi

Connection Details:

Matrix-Sound_Sensor	NanoPi
S	Pin7
V	Pin4
G	Pin6

6.3 Compile Test Program

Please login the matrix hub and enter the nanopi branch

$ cd matrix
$ git checkout nanopi

Compile the matrix code

$ make CROSS_COMPILE=arm-linux- clean
$ make CROSS_COMPILE=arm-linux-
$ make CROSS_COMPILE=arm-linux- install

Note: please make sure to install the cross compiler "arm-linux-gcc-4.4.3" on your PC, which is used to compile files for the NanoPi-Debian.
Generated library files are under the "install/lib" directory. Applications are under the "install/usr/bin" directory. The test program for the "Matrix-Ultrasonic_Ranger" module is "matrix-ultrasonic_ranger".

6.4 Run Test Program

Please copy the library files and test program to the NanoPi

$ cp install/usr/bin/* nanopi_rootfs/usr/bin/
$ cp install/lib/* nanopi_rootfs/lib/ -d

Power on the NanoPi and run the following command in Debian's terminal
Note: this module is not plug and play therefore before running the module please make sure it is connected to a NanoPi.

$ matrix-ultrasonic_ranger

6.5 Code Sample

int main(int argc, char ** argv)
{
    int distance = -1;
 
    int pin = GPIO_PIN1;
 
    if (Hcsr04Init(pin) == -1) {
        printf("Fail to init hcsr04\n");
    }
    if (Hcsr04Read(&distance) != -1) {
        printf("Get distance: %3d cm\n", distance);
    } else {
        printf("Faid to get distance\n");
    }
    Hcsr04DeInit();
    return 0;
}

7 Connect to Tiny4412

7.1 Preparations

Please refer to the Tiny4412's user's manual to install a UbuntuCore on the Tiny4412 and install an appropriate cross compiler on a PC.
Note: only the Tiny4412SDK-1506 carrier board can work with this module.

7.2 Hardware Connection

Please refer to the following diagram to connect the Matrix-Ultrasonic_Ranger to the Tiny4412

Connection Details:

Matrix- Ultrasonic Ranger	Tiny4412
S	GPIO1 S
V	GPIO1 5V
G	GPIO1 GND

7.3 Compile Test Program

Please login the Matrix hub and enter the matrix-tiny4412 branch

$ cd matrix
$ git checkout tiny4412

Compile the matrix code

$ make CROSS_COMPILE=arm-linux-gnueabihf- clean
$ make CROSS_COMPILE=arm-linux-gnueabihf-
$ make CROSS_COMPILE=arm-linux-gnueabihf- install

Note: please make sure to install the cross compiler "arm-linux-gnueabihf-gcc-4.7.3" on your PC, which is used to compile files for the Tiny4412-UbuntuCore.
Generated library files are under the "install/lib" directory. Applications are under the "install/usr/bin" directory. The test program for the "Matrix-Ultrasonic_Ranger" module is "matrix-ultrasonic_ranger".

7.4 Run Test Program

Please copy the library files and test program to the Tiny4412

$ cp install/usr/bin/* tiny4412_rootfs/usr/bin/
$ cp install/lib/* tiny4412_rootfs/lib/ -d

Power on the Tiny4412 and run the following command in UbuntuCore's terminal
Note: this module is not plug and play therefore before running the module please make sure it is connected to a Tiny4412.

$ matrix-ultrasonic_ranger

7.5 Code Sample

int main(int argc, char ** argv)
{
    int distance = -1;
 
    int pin = GPIO_PIN1;
 
    if (Hcsr04Init(pin) == -1) {
        printf("Fail to init hcsr04\n");
    }
    if (Hcsr04Read(&distance) != -1) {
        printf("Get distance: %3d cm\n", distance);
    } else {
        printf("Faid to get distance\n");
    }
    Hcsr04DeInit();
    return 0;
}

@@ Line 33: / Line 33: @@
 Each branch in this hub contains the matrix modules' code samples for a board that the matrix modules can work with.<br>
 * The nanopi branch contains the matrix modules' code samples for the NanoPi
+* The nanopi 2 branch contains the matrix modules' code samples for the NanoPi 2
 * The tiny4412 branch contains the matrix modules' code samples for the Tiny4412
 * The raspberrypi branch contains the matrix modules' code samples for the RaspberryPi
@@ Line 47: / Line 48: @@
 </syntaxhighlight>
 If this is successful a "matrix" directory will be generated, which will contain all the matrix modules' code samples.
+==Connect to NanoPi 2==
+===Hardware Connection===
+Please refer to the following connection diagram to connect the Matrix-Ultrasonic_Ranger to the NanoPi 2:<br>
+[[File:Matrix-Ultrasonic_Ranger_nanopi_2.jpg|frameless|600px|Matrix-Ultrasonic_Ranger_nanopi_2]]
+Connection Details:
+{| class="wikitable"
+|-
+|Matrix-Ultrasonic_Ranger || NanoPi 2
+|-
+|S   || Pin7
+|-
+|V   || Pin4
+|-
+|G   || Pin6
+|}
+===编译测试程序===
+进入Matrix代码仓库，切换到nanopi2分支
+<syntaxhighlight lang="bash">
+$ cd matrix
+$ git checkout nanopi2
+</syntaxhighlight>
+编译Matrix配件代码
+<syntaxhighlight lang="bash">
+$ make CROSS_COMPILE=arm-linux- clean
+$ make CROSS_COMPILE=arm-linux-
+$ make CROSS_COMPILE=arm-linux- install
+</syntaxhighlight>
+注意：请确保你的主机PC当前使用的交叉编译器为NanoPi 2配套的arm-linux-gcc-4.9.3。<br>
+编译成功后库文件位于install/lib目录下，而测试程序则位于install/usr/bin目录下，模块Matrix-Ultrasonic_Ranger对应的测试程序为matrix-ultrasonic_ranger。<br>
+硬件驱动模块位于modules目录下，对应的驱动源码都包含在在NanoPi 2的Linux内核仓库里：https://github.com/friendlyarm/linux-3.4.y.git <br>
+===运行测试程序===
+将带有Debian系统的SD卡插入一台运行Linux的电脑，可以挂载SD卡上的boot和rootfs分区。<br>
+假设rootfs分区的挂载路径为/media/rootfs，执行以下命令将Matrix的硬件驱动、库文件和测试程序拷贝到NanoPi 2的文件系统上。<br>
+<syntaxhighlight lang="bash">
+$ cp modules /media/rootfs/ -r
+$ cp install/lib/* /media/rootfs/lib/ -d
+$ cp install/usr/bin/* /media/rootfs/usr/bin/
+</syntaxhighlight>
+将SD卡重新插入NanoPi 2，上电启动，在Debian的shell终端中执行以下命令加载硬件驱动。<br>
+<syntaxhighlight lang="bash">
+$ cd /modules
+$ insmod matrix_hcsr04.ko
+</syntaxhighlight>
+运行模块Matrix-Ultrasonic_Ranger的测试程序。<br>
+<syntaxhighlight lang="bash">
+$ matrix-ultrasonic_ranger
+</syntaxhighlight>
+运行效果如下：<br>
+[[File:matrix-ultrasonic_ranger_result.png|frameless|600px|matrix-ultrasonic_ranger_result]]
+===Code Sample===
+<syntaxhighlight lang="c">
+int main(int argc, char ** argv)
+{
+    int distance = -1;
+    int pin = GPIO_PIN(7);
+    if (Hcsr04Init(pin) == -1) {
+        printf("Fail to init hcsr04\n");
+    }
+    if (Hcsr04Read(&distance) != -1) {
+        printf("Get distance: %3d cm\n", distance);
+    } else {
+        printf("Faid to get distance\n");
+    }
+    Hcsr04DeInit();
+    return 0;
+}
+</syntaxhighlight>
 ==Connect to NanoPi==
@@ Line 205: / Line 283: @@
 ==Resources==
+==Update Log==
+===Feb-23-2016===
+* Added the description for "NanoPi 2 branch" in Section 4
+* Added Section 5: Connect to NanoPi 2
 <!--