Difference between revisions of "CVBS"
From FriendlyELEC WiKi
(→H3主线内核配置CVBS输出) |
(→H3主线内核配置CVBS输出) |
||
| Line 1: | Line 1: | ||
| − | === | + | ===H3 Linux-3.4 BSP配置CVBS输出=== |
| − | + | 对于H3 Linux-3.4系统映像，NanoPi M1 Plus / NanoPi M1 / NanoPi Duo2 支持配置为CVBS输出。由于HDMI / CVBS只能选择一路显示输出，而HDMI输出更通用一些，所以M1 Plus / M1默认是使能HDMI禁止CVBS，而Duo2由于没有HDMI接口，所有默认是使能CVBS。 | |
| + | |||
| + | 参考下列操作可以自行手动为M1 Plus / M1使能CVBS输出。 | ||
| + | |||
| + | ====参考文档==== | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | $ git clone https://github.com/friendlyarm/h3_lichee.git lichee --depth 1 | ||
| + | $ ls lichee/doc/H3 sys_config.fex使用配置说明V1.1.pdf。 | ||
| + | </syntaxhighlight> | ||
| + | |||
| + | ====修改sys_config==== | ||
| + | 以NanoPi M1 Plus为例，NanoPi M1的修改操作也是类似的。<br> | ||
| + | M1 Plus的sys_config文件路径如下: | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | $ ls lichee/tools/pack/chips/sun8iw7p1/configs/nanopi-h3/board/sys_config_nanopi-m1-plus.fex | ||
| + | </syntaxhighlight> | ||
| + | |||
| + | 使能CVBS输出: | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | [disp_init] | ||
| + | disp_init_enable = 1 | ||
| + | disp_mode = 1 | ||
| + | screen0_output_type = 3 | ||
| + | screen0_output_mode = 4 | ||
| + | screen1_output_type = 2 | ||
| + | screen1_output_mode = 14 | ||
| + | fb0_format = 0 | ||
| + | fb0_width = 0 | ||
| + | fb0_height = 0 | ||
| + | fb1_format = 0 | ||
| + | fb1_width = 0 | ||
| + | fb1_height = 0 | ||
| + | |||
| + | [hdmi_para] | ||
| + | hdmi_used = 0 | ||
| + | hdmi_power = "vcc-hdmi-18" | ||
| + | |||
| + | [tv_para] | ||
| + | tv_used = 1 | ||
| + | tv_dac_used = 1 | ||
| + | tv_dac_src0 = 0 | ||
| + | </syntaxhighlight> | ||
Revision as of 07:33, 18 December 2018
1 H3 Linux-3.4 BSP配置CVBS输出
对于H3 Linux-3.4系统映像，NanoPi M1 Plus / NanoPi M1 / NanoPi Duo2 支持配置为CVBS输出。由于HDMI / CVBS只能选择一路显示输出，而HDMI输出更通用一些，所以M1 Plus / M1默认是使能HDMI禁止CVBS，而Duo2由于没有HDMI接口，所有默认是使能CVBS。
参考下列操作可以自行手动为M1 Plus / M1使能CVBS输出。
1.1 参考文档
$ git clone https://github.com/friendlyarm/h3_lichee.git lichee --depth 1 $ ls lichee/doc/H3 sys_config.fex使用配置说明V1.1.pdf。
1.2 修改sys_config
以NanoPi M1 Plus为例，NanoPi M1的修改操作也是类似的。
M1 Plus的sys_config文件路径如下:
$ ls lichee/tools/pack/chips/sun8iw7p1/configs/nanopi-h3/board/sys_config_nanopi-m1-plus.fex
使能CVBS输出:
[disp_init] disp_init_enable = 1 disp_mode = 1 screen0_output_type = 3 screen0_output_mode = 4 screen1_output_type = 2 screen1_output_mode = 14 fb0_format = 0 fb0_width = 0 fb0_height = 0 fb1_format = 0 fb1_width = 0 fb1_height = 0 [hdmi_para] hdmi_used = 0 hdmi_power = "vcc-hdmi-18" [tv_para] tv_used = 1 tv_dac_used = 1 tv_dac_src0 = 0
