Difference between revisions of "RK3399-Android7"

Latest revision as of 10:58, 19 November 2018

查看中文

1 Work with Android7.1

rk3399-android7-home

rk3399-android7-icons

FriendlyElec provides a full Android7.1 BSP for RK3399 board. The source code is hosted at gitlab.com and is open source. The BSP supports GPU and VPU hardware acceleration.

1.1 Connect MIPI Camera to {{{1}}}

FriendlyElec developed a MIPI camera CAM1320 for board and it works under Android. You can use this camera to take pictures and record video. The operation is straightforward. You just need to connect the camera at your board's MIPI interface, boot your board to Android and start Android's camera app.

1.2 Set HDMI Display

If your board is connected to an HDMI monitor and it runs Android you can go to "Settings -> Display -> HDMI" to make your setting.

HDMI Resolution	By default it is "Auto". You can set its resolution up to 4K
Screen Zoom	There will be four arrows you can click on to zoom in/out
HDMI Rotation	Set it landscape or portrait.

1.3 Rotate Display

Enter Android's Settings -> Display -> HDMI -> HDMI Rotation. It supports both landscape and portrait.

1.4 Android7 hardware access

You can use the FriendlyThings SDK to access and control hardware resources on the motherboard in the Android App, such as Uart, SPI, I2C, GPIO and other interfaces. For details, please refer to the following two documents.：

• Android: FriendlyThings for Rockchip
• Android: FriendlyThings APIs

1.5 Navigate Android with Remote Control

The {{{1}}} supports the FriendlyARM RC-100 remote control under Android. To get a better experience your can connect your T4 to an HDMI monitor and navigate Android.


Here is a table for the remote control's keys and corresponding functions:

Key	Function
Up	Navigate - Up
Down	Navigate - Down
Left	Navigate - Left
Right	Navigate - Right
OK	Confirm
-	Volume -
+	Volume +
Mute	Mute
Menu	Android Menu
Home	Android Home
Return	Android Return
F1	Pull-Down Android Message Bar
F2	Android Screenshot
F3	Switch between mouse and key

1.6 Work with USB Camera to Take Pictures and Record Video

FriendlyELEC's Android system supports picture taking and video recording with a USB camera, Android's camera app has these functions. When you use the app to take pictures or record video you need to be aware of the following two things:
1) Make sure your camera's resolution works. We suggest you try a camera with a lower CIF resolution first. If it works you may switch to a camera with a higher resolution:
;
2）A USB camera cannot work simultaneously with a MIPI camera. Plug and play is not supporter for camera modules. After you connect a camera to a board you need to reboot your board to enable the camera.

Here are the camera modules we tested: Logitech C270 and LogitechC922 PRO
In our test the resolution was 1080P when we used a Logitech C922 PRO to take pictures or record video.

1.7 Using 4G Module EC20 on Android

1.7.1 Hardware Setup

Connect an EC20 module to a USB to miniPCIe board and connect the board to an ARM board's USB Host. Here is a hardware setup:

Power on the board and you will be able to surf the internet with the 4G module like using an Android phone.

1.7.2 Activate EC20's GPS Functions

By default GPS functions are disabled in Android. If GPS functions are enabled in Android but no GPS module is detected Android will continuously output log messages. After an EC20 module is connected you can enable GPS functions.
To enable the GPS functions open the "vendor/quectel/ec20/BoardConfigPartial.mk" file and change the following line:

BOARD_HAS_GPS := false

to

BOARD_HAS_GPS := true

and recompile Android。