Difference between revisions of "NanoPC-T4"
From FriendlyELEC WiKi
(→Layout) |
(→Layout) |
||
| Line 55: | Line 55: | ||
|3 || I2C2_SDA(3V) ||4 || VCC5V0_SYS | |3 || I2C2_SDA(3V) ||4 || VCC5V0_SYS | ||
|- | |- | ||
| − | |5 || I2C2_SCL(3V) ||6 || | + | |5 || I2C2_SCL(3V) ||6 || GND |
|- | |- | ||
|7 || GPIO1_A0(3V) ||8 || UART2B_TX(3V) | |7 || GPIO1_A0(3V) ||8 || UART2B_TX(3V) | ||
|- | |- | ||
| − | |9 || | + | |9 || GND ||10 || UART2B_RX(3V) |
|- | |- | ||
|11 || GPIO1_A1(3V) ||12 || GPIO1_C2(3V) | |11 || GPIO1_A1(3V) ||12 || GPIO1_C2(3V) | ||
|- | |- | ||
| − | |13 || GPIO1_A3(3V) ||14 || | + | |13 || GPIO1_A3(3V) ||14 || GND |
|- | |- | ||
|15 || GPIO1_A4(3V) ||16 || GPIO1_C6(3V) | |15 || GPIO1_A4(3V) ||16 || GPIO1_C6(3V) | ||
| Line 69: | Line 69: | ||
|17 || VCC3V3_SYS ||18 || GPIO1_C7(3V) | |17 || VCC3V3_SYS ||18 || GPIO1_C7(3V) | ||
|- | |- | ||
| − | |19 || SPI1_TXD/UART4_TX(3V) ||20 || | + | |19 || SPI1_TXD/UART4_TX(3V) ||20 || GND |
|- | |- | ||
|21 || SPI1_RXD/UART4_RX(3V) ||22 || GPIO1_D0(3V) | |21 || SPI1_RXD/UART4_RX(3V) ||22 || GPIO1_D0(3V) | ||
| Line 75: | Line 75: | ||
|23 || SPI1_CLK(3V) ||24 || SPI1_CSn0(3V) | |23 || SPI1_CLK(3V) ||24 || SPI1_CSn0(3V) | ||
|- | |- | ||
| − | |25 || | + | |25 || GND ||26 || GPIO4_C5/SPDIF_TX(3V) |
|- | |- | ||
|27 || I2C2_SDA(1.8V) ||28 || I2C2_SCL(1.8V) | |27 || I2C2_SDA(1.8V) ||28 || I2C2_SCL(1.8V) | ||
|- | |- | ||
| − | |29 || I2S1_LRCK_RX(1.8V) ||30 || | + | |29 || I2S1_LRCK_RX(1.8V) ||30 || GND |
|- | |- | ||
|31 ||I2S1_LRCK_TX(1.8V) ||32 || I2S_CLK(1.8V) | |31 ||I2S1_LRCK_TX(1.8V) ||32 || I2S_CLK(1.8V) | ||
|- | |- | ||
| − | |33 || I2S1_SCLK(1.8V) ||34 || | + | |33 || I2S1_SCLK(1.8V) ||34 || GND |
|- | |- | ||
|35 || I2S1_SDI0(1.8V) ||36 || I2S1_SDO0(1.8V) | |35 || I2S1_SDI0(1.8V) ||36 || I2S1_SDO0(1.8V) | ||
| Line 89: | Line 89: | ||
|37 || GPIO3_D4(1.8V) ||38 || GPIO3_D5(1.8V) | |37 || GPIO3_D4(1.8V) ||38 || GPIO3_D5(1.8V) | ||
|- | |- | ||
| − | |39 || | + | |39 || GND ||40 || GPIO3_D6(1.8V) |
|} | |} | ||
Revision as of 06:05, 21 May 2018
Contents
1 Introduction
2 Hardware Spec
- SoC: Rockchip RK3399
- CPU: big.LITTLE，Dual-Core Cortex-A72(up to 2.0GHz) + Quad-Core Cortex-A53(up to 1.5GHz)
- GPU: Mali-T864 GPU，supports OpenGL ES1.1/2.0/3.0/3.1, OpenVG1.1, OpenCL, DX11, and AFBC
- VPU: 4K VP9 and 4K 10bits H265/H264 60fps decoding, Dual VOP, etc
- PMU: RK808-D PMIC, cooperated with independent DC/DC, enabling DVFS, solfware power-down, RTC wake-up, system sleep mode
- RAM: Dual-Channel 4GB LPDDR3
- Flash: 16GB eMMC 5.1 Flash
- Ethernet: Native Gigabit Ethernet
- Wi-Fi/BT: 802.11a/b/g/n/ac, Bluetooth 4.1, Wi-Fi and Bluetooth combo module, dual antenna interface
- Video Input: two 4-Line MIPI-CSI, dual ISP, up to 13MPix/s，supports simultaneous input of dual camera data
- Video output
- HDMI: HDMI 2.0a, supports 4K 60Hz，HDCP 1.4/2.2
- DP on Type-C: DisplayPort 1.2 Alt Mode on USB Type-C
- LCD Interface: one eDP 1.3（4 line，10.8Gbps）, one 4-Line MIPI-DSI
- Audio Out: 3.5mm Dual channel headphone jack, or HDMI
- Audio In: Onboard microphone
- USB 2.0: 2 independent native USB 2.0 Host A interfaces
- USB 3.0: 1 native USB 3.0 Host A type interface
- USB Type-C: Supports USB3.0 Type-C and DisplayPort 1.2 Alt Mode on USB Type-C
- PCIe: One M.2 M-Key PCIe x4 socket, compatible with PCIe 2.1, Dual operation mode; Onboard M3 PCB nut for mounting M.2 2280 module
- 40Pin GPIO Extension ports:
- 1 X 3V/1.8V I2C, up to 2 x 3V UART, 1 X 3V SPI, 1 x SPDIF_TX, up to 8 x 3V GPIOs
- 1 x 1.8V I2S, 3 x 1.8V GPIOs
- ADC: 3 x 1.8V ADC inputs, 5 Pin 2.54mm header
- Debug: one Debug UART, 4 Pin 2.54mm header, 3V level, 1500000bps
- Keys: PowerKey, Reset, MASKROM(BOOT), Recovery
- LED: 1 x power LED and 1 x GPIO Controled LED
- IR reciver: Onboard IR reciver, Acceptes 38KHz carrier frequency
- RTC Battery: 2 Pin 1.27/1.25mm RTC battery input connector
- Cooling: two 2.5mm PCB nuts for mounting heat sink; 3 Pin 12V cooling fan interface with PWM
- Power supply: DC 12V/2A
- PCB: Ten Layer, 100 mm x 64 mm
- Ambient Operating Temperature: 0℃ to 80℃
3 Software Features
4 Diagram, Layout and Dimension
4.1 Layout
File:NanoPC-T4-1802-IF-01.png
NanoPC-T4 Layout
- 40 Pin GPIO Pin Spec
Pin# Name Pin# Name 1 VCC3V3_SYS 2 VCC5V0_SYS 3 I2C2_SDA(3V) 4 VCC5V0_SYS 5 I2C2_SCL(3V) 6 GND 7 GPIO1_A0(3V) 8 UART2B_TX(3V) 9 GND 10 UART2B_RX(3V) 11 GPIO1_A1(3V) 12 GPIO1_C2(3V) 13 GPIO1_A3(3V) 14 GND 15 GPIO1_A4(3V) 16 GPIO1_C6(3V) 17 VCC3V3_SYS 18 GPIO1_C7(3V) 19 SPI1_TXD/UART4_TX(3V) 20 GND 21 SPI1_RXD/UART4_RX(3V) 22 GPIO1_D0(3V) 23 SPI1_CLK(3V) 24 SPI1_CSn0(3V) 25 GND 26 GPIO4_C5/SPDIF_TX(3V) 27 I2C2_SDA(1.8V) 28 I2C2_SCL(1.8V) 29 I2S1_LRCK_RX(1.8V) 30 GND 31 I2S1_LRCK_TX(1.8V) 32 I2S_CLK(1.8V) 33 I2S1_SCLK(1.8V) 34 GND 35 I2S1_SDI0(1.8V) 36 I2S1_SDO0(1.8V) 37 GPIO3_D4(1.8V) 38 GPIO3_D5(1.8V) 39 GND 40 GPIO3_D6(1.8V)
- eDP Interface Pin Spec
Pin# Name Pin# Name
- MIPI-CSI Interface Pin Spec
Pin# MIPI-CSI2
- MIPI-DSI Interface Pin Spec
Pin# Name
- Notes
- VCC5V0_SYS: 5V Output
- VCC3V3_SYS: 3.3V Output
- For more details refer to the document:
4.2 Board Dimension
- For more details refer to the document:
- Power Jack
