Difference between revisions of "NanoPC-T4"
From FriendlyELEC WiKi
(→Introduction) |
(→Introduction) |
||
| Line 27: | Line 27: | ||
* 40Pin GPIO Extension ports: | * 40Pin GPIO Extension ports: | ||
** 1 X 3V/1.8V I2C, up to 2 x 3V UART, 1 X 3V SPI, 1 x SPDIF_TX, up to 8 x 3V GPIOs | ** 1 X 3V/1.8V I2C, up to 2 x 3V UART, 1 X 3V SPI, 1 x SPDIF_TX, up to 8 x 3V GPIOs | ||
| − | ** | + | ** 1 x 1.8V I2S, 3 x 1.8V GPIO |
* ADC: 3 x 1.8V ADC inputs, 5 Pin 2.54mm header | * ADC: 3 x 1.8V ADC inputs, 5 Pin 2.54mm header | ||
* Debug: one Debug UART, 4 Pin 2.54mm header, 3V level, 1500000bps | * Debug: one Debug UART, 4 Pin 2.54mm header, 3V level, 1500000bps | ||
Revision as of 05:31, 21 May 2018
Contents
1 Introduction
- SoC: Rockchip RK3399
- CPU: big.LITTLE，Dual-Core Cortex-A72(up to 2.0GHz) + Quad-Core Cortex-A53(up to 1.5GHz)
- GPU: Mali-T864 GPU，supports OpenGL ES1.1/2.0/3.0/3.1, OpenVG1.1, OpenCL, DX11, and AFBC
- VPU: 4K VP9 and 4K 10bits H265/H264 60fps decoding, Dual VOP, etc
- PMU: RK808-D PMIC, cooperated with independent DC/DC, enabling DVFS, solfware power-down, RTC wake-up, system sleep mode
- RAM: Dual-Channel 4GB LPDDR3
- Flash: 16GB eMMC 5.1 Flash
- Ethernet: Native Gigabit Ethernet
- Wi-Fi/BT: 802.11a/b/g/n/ac, Bluetooth 4.1, Wi-Fi and Bluetooth combo module, dual antenna interface
- Video Input: two 4-Line MIPI-CSI, dual ISP, up to 13MPix/s，supports simultaneous input of dual camera data
- Video output
- HDMI: HDMI 2.0a, supports 4K 60Hz，HDCP 1.4/2.2
- DP on Type-C: DisplayPort 1.2 Alt Mode on USB Type-C
- LCD Interface: one eDP 1.3（4 line，10.8Gbps）, one 4-Line MIPI-DSI
- Audio Out: 3.5mm Dual channel headphone jack, or HDMI
- Audio In: Onboard microphone
- USB 2.0: 2 independent native USB 2.0 Host A interfaces
- USB 3.0: 1 native USB 3.0 Host A type interface
- USB Type-C: Supports USB3.0 Type-C and DisplayPort 1.2 Alt Mode on USB Type-C
- PCIe: One M.2 M-Key PCIe x4 socket, compatible with PCIe 2.1, Dual operation mode; Onboard M3 PCB nut for mounting M.2 2280 module
- 40Pin GPIO Extension ports:
- 1 X 3V/1.8V I2C, up to 2 x 3V UART, 1 X 3V SPI, 1 x SPDIF_TX, up to 8 x 3V GPIOs
- 1 x 1.8V I2S, 3 x 1.8V GPIO
- ADC: 3 x 1.8V ADC inputs, 5 Pin 2.54mm header
- Debug: one Debug UART, 4 Pin 2.54mm header, 3V level, 1500000bps
- Keys: PowerKey, Reset, MASKROM(BOOT), Recovery
- LED: 1 x power LED and 1 x GPIO Controled LED
- IR reciver: Onboard IR reciver, Acceptes 38KHz carrier frequency
- RTC Battery: 2 Pin 1.27/1.25mm RTC battery input connector
- Cooling: two 2.5mm PCB nuts for mounting heat sink; 3 Pin 12V cooling fan interface with PWM
- Power supply: DC 12V/2A
- PCB: Ten Layer, 100 mm x 64 mm
- Ambient Operating Temperature: 0℃ to 80℃
2 Software Features
3 Diagram, Layout and Dimension
3.1 Layout
File:NanoPC-T4-1802-IF-01.png
NanoPC-T4 Layout
- 40Pin GPIO Pin Spec
Pin# Name Pin# Name
- eDP Interface Pin Spec
Pin# Name Pin# Name
- MIPI-CSI Interface Pin Spec
Pin# MIPI-CSI2
- MIPI-DSI Interface Pin Spec
Pin# Name
- Notes
- For more details refer to the document:
3.2 Board Dimension
- For more details refer to the document:
- Power Jack
