Difference between revisions of "RTC"
From FriendlyELEC WiKi
(updated by API) |
(→Step3: Verify that the RTC is working properly) |
||
| (7 intermediate revisions by the same user not shown) | |||
| Line 77: | Line 77: | ||
</syntaxhighlight> | </syntaxhighlight> | ||
Once again, rtc1 is our external RTC, and a value of 1 for hctosys means that the kernel will set the system time at boot time. | Once again, rtc1 is our external RTC, and a value of 1 for hctosys means that the kernel will set the system time at boot time. | ||
| − | ===set | + | ===set the RTC from the system time=== |
You can also use the following command: | You can also use the following command: | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | sudo hwclock | + | sudo hwclock -f /dev/rtc1 -w |
</syntaxhighlight> | </syntaxhighlight> | ||
View current hardware clock: | View current hardware clock: | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | sudo hwclock -- | + | sudo hwclock -f /dev/rtc1 -r |
| + | </syntaxhighlight> | ||
| + | |||
| + | ===set the system time from the RTC=== | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | sudo hwclock -f /dev/rtc1 -s | ||
</syntaxhighlight> | </syntaxhighlight> | ||
| Line 99: | Line 104: | ||
Shut down the board and disconnect the network cable, reboot after a while, check whether the system time is correct: | Shut down the board and disconnect the network cable, reboot after a while, check whether the system time is correct: | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | echo "sys time: $(date)" && echo "hw time: " $(sudo hwclock | + | echo "sys time: $(date)" && echo "hw time: " $(sudo hwclock -f /dev/rtc1 -r) |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
</syntaxhighlight> | </syntaxhighlight> | ||
Latest revision as of 09:53, 1 September 2022
Contents
1 Step1: Set timezone
1.1 View available time zones
timedatectl list-timezones
1.2 Change time zone
sudo timedatectl set-timezone Asia/Hong_Kong
1.3 Check current system time
date2 Step2: Change time synchronization service to ntpd (requires network connection)
2.1 Use ntpd instead of timesyncd
sudo timedatectl set-ntp no sudo apt update sudo apt install ntp
3 Step2: Setting up RTC device (Use Matrix-RTC as example)
3.1 Build the RTC driver into the kernel (not an external module)
Go to the following location:
│ Location: │ │ -> Device Drivers │ │ -> Real Time Clock (RTC_CLASS [=y]) │
Set CONFIG_RTC_DRV_DS1307 to 'y'.
3.2 Specify the correct RTC device
Since the default kernel rtc device is rtc0, and when we use external rtc in Allwinner platform, the external rtc is usually initialized to rtc1, so we also need to modify the following kernel configuration to set the value to rtc1:
CONFIG_RTC_HCTOSYS_DEVICE="rtc1" CONFIG_RTC_SYSTOHC_DEVICE="rtc1"
The kernel configuration:
diff --git a/arch/arm/configs/sunxi_defconfig b/arch/arm/configs/sunxi_defconfig index 4c88bbb8..4dbee1a9 100644 --- a/arch/arm/configs/sunxi_defconfig +++ b/arch/arm/configs/sunxi_defconfig @@ -1027,11 +1027,12 @@ CONFIG_LEDS_TRIGGER_DEFAULT_ON=y CONFIG_LEDS_TRIGGER_PANIC=y CONFIG_LEDS_TRIGGER_NETDEV=y CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc1" CONFIG_RTC_INTF_DEV_UIE_EMUL=y CONFIG_RTC_DRV_TEST=m CONFIG_RTC_DRV_ABB5ZES3=m CONFIG_RTC_DRV_ABX80X=m -CONFIG_RTC_DRV_DS1307=m +CONFIG_RTC_DRV_DS1307=y CONFIG_RTC_DRV_DS1307_CENTURY=y CONFIG_RTC_DRV_DS1374=m CONFIG_RTC_DRV_DS1374_WDT=y
3.3 Check the driver information of rtc
pi@NanoPi-M1-Plus:~$ dmesg | grep rtc [ 2.470518] sun6i-rtc 1f00000.rtc: rtc core: registered rtc-sun6i as rtc0 [ 2.477351] sun6i-rtc 1f00000.rtc: RTC enabled [ 2.489685] rtc-ds1307 0-0068: registered as rtc1 [ 4.009223] rtc-ds1307 0-0068: setting system clock to 2022-03-04 08:22:13 UTC (1646382133)
From the above information, we can see that the external RTC is initialized as rtc1
3.4 Testing external RTC
$ cat /sys/class/rtc/rtc1/name rtc-ds1307 0-0068 $ cat /sys/class/rtc/rtc1/time 00:32:27 $ cat /sys/class/rtc/rtc1/hctosys 1
Once again, rtc1 is our external RTC, and a value of 1 for hctosys means that the kernel will set the system time at boot time.
3.5 set the RTC from the system time
You can also use the following command:
sudo hwclock -f /dev/rtc1 -w
View current hardware clock:
sudo hwclock -f /dev/rtc1 -r
3.6 set the system time from the RTC
sudo hwclock -f /dev/rtc1 -s
3.7 Some other modifications
Edit the following file, replacing rtc0 with rtc1:
/etc/crontab /etc/init.d/hwclock.sh /etc/init.d/sync_ntp_rtc
4 Step3: Verify that the RTC is working properly
4.1 Test read time from RTC
Shut down the board and disconnect the network cable, reboot after a while, check whether the system time is correct:
echo "sys time: $(date)" && echo "hw time: " $(sudo hwclock -f /dev/rtc1 -r)
