Difference between revisions of "NanoPi Duo2 IoT-Box"

From FriendlyELEC WiKi
Jump to: navigation, search
(Introduction)
(updated by API)
 
(14 intermediate revisions by 2 users not shown)
Line 8: Line 8:
 
*It has an onboard quad-band GSM/GPRS module SIM800C.
 
*It has an onboard quad-band GSM/GPRS module SIM800C.
 
*It has 2.0mm I2C interface, UART interface, audio interface and CVBS interface etc and can work with various external modules.
 
*It has 2.0mm I2C interface, UART interface, audio interface and CVBS interface etc and can work with various external modules.
*Its MicroUSB port is only used as power output. And a power switch is added too.
+
*Its MicroUSB port is only used as power input. And a power switch is added too.
 
*It has one power LED and one GPIO accessed LED.
 
*It has one power LED and one GPIO accessed LED.
 
*It populates the two USB ports of the NanoPi Duo2.
 
*It populates the two USB ports of the NanoPi Duo2.
 
*It populates the serial ports and Ethernet port of the NanoPi Duo2.
 
*It populates the serial ports and Ethernet port of the NanoPi Duo2.
*It has an IPX to SMA antenna connector for WiFi antennas.
+
*It has an IPX to SMA antenna converter for WiFi antennas.
  
==特性==
+
==Hardware Spec==
* 板载四频GSM/GPRS模块
+
* Onboard quad-band GSM/GPRS module
* 2个USB Host接口
+
* 2 x USB Host
* 扩展的调试串口和网络接口
+
* Serial port and Ethernet port
* 音频输入、输出接口
+
* Audio input and output
* MicroUSB电源输入,并添加了电源开关
+
* MicroUSB power input and a power switch
* IPX转SMA WiFi天线转接线
+
* IPX to SMA WiFi converter
* PCB尺寸(mm):85x56
+
* PCB dimension (mm): 85x56
 
[[File:NanoPi Duo2 IoT-Box_PCB.png | frameless|600px|NanoPi Duo2 IoT-Box_PCB]]
 
[[File:NanoPi Duo2 IoT-Box_PCB.png | frameless|600px|NanoPi Duo2 IoT-Box_PCB]]
  
===接口说明===
+
===Layout===
[[File:NanoPi Duo2 IoT-Box-layout.jpg |thumb|550px|NanoPi Duo2 IoT-Box接口布局]]
+
[[File:NanoPi Duo2 IoT-Box-layout.jpg |thumb|550px|NanoPi Duo2 IoT-Box Layout]]
NanoPi Duo2 IoT-Box接口如右图所示,接口引脚丝印都在板子背面做了详细标注。<br>
+
Here is the NanoPi Duo2 IoT-Box's layout. Its pins' remarks are printed on the board.<br>
  
*  '''NanoPi Duo header引脚定义 '''
+
*  '''NanoPi Duo header Pin Spec '''
 
::{| class="wikitable"
 
::{| class="wikitable"
 
|-
 
|-
| Number# || Name ||  || Number# || Name   
+
| Number# || Name|| Number# || Name   
 
|-
 
|-
| 1 || VDD_5V ||  ||  17  ||  DEBUG_RX(UART_RXD0)/GPIOA5/PWM0
+
| 1 || VDD_5V ||  17  ||  DEBUG_RX(UART_RXD0)/GPIOA5/PWM0
 
|-
 
|-
| 2 || VDD_5V ||    ||  18 || DEBUG_TX(UART_TXD0)/GPIOA4
+
| 2 || VDD_5V ||  18 || DEBUG_TX(UART_TXD0)/GPIOA4
 
|-  
 
|-  
| 3 ||  SYS_3.3V  ||    ||  19 ||    GND   
+
| 3 ||  SYS_3.3V  ||  19 ||    GND   
 
|-
 
|-
| 4 ||GND  ||  || 20  ||  I2C0_SCL/GPIOA11
+
| 4 ||GND  ||  20  ||  I2C0_SCL/GPIOA11
 
|-
 
|-
| 5 || GPIOL11/IR-RX ||  || 21  ||  I2C0_SDA/GPIOA12
+
| 5 || GPIOL11/IR-RX || 21  ||  I2C0_SDA/GPIOA12
 
|-  
 
|-  
|6  ||  GPIOG11 ||   || 22  || UART3_TX/SPI1_CS/GPIOA13
+
|6  ||  GPIOG11    || 22  || UART3_TX/SPI1_CS/GPIOA13
 
|-
 
|-
| 7||USB-DM3 ||     || 23  ||  UART3_RX/SPI1_CLK/GPIOA14  
+
| 7||USB-DM3    || 23  ||  UART3_RX/SPI1_CLK/GPIOA14  
 
|-
 
|-
|8  ||  USB-DP3 ||     || 24  || UART3_CTS/SPI1_MISO/GPIOA16
+
|8  ||  USB-DP3    || 24  || UART3_CTS/SPI1_MISO/GPIOA16
 
|-
 
|-
| 9 ||USB-DM2 ||       ||25  ||  UART3_RTS/SPI1_MOSI/GPIOA15
+
| 9 ||USB-DM2      ||25  ||  UART3_RTS/SPI1_MOSI/GPIOA15
 
|-
 
|-
| 10|| USB-DP2     ||   || 26  ||  UART1_RX/GPIOG7
+
| 10|| USB-DP2  || 26  ||  UART1_RX/GPIOG7
 
|-
 
|-
|11 ||EPHY-RXN || || 27  ||  UART1_TX/GPIOG6  
+
|11 ||EPHY-RXN  || 27  ||  UART1_TX/GPIOG6  
 
|-
 
|-
| 12 || EPHY-RXP     ||       || 28  ||  CVBS   
+
| 12 || EPHY-RXP      || 28  ||  CVBS   
 
|-
 
|-
|13 || EPHY-TXN     ||     || 29  ||  LINEOUT_L  
+
|13 || EPHY-TXN    || 29  ||  LINEOUT_L  
 
|-
 
|-
|14  ||EPHY-TXP ||       || 30  ||  LINEOUT_R   
+
|14  ||EPHY-TXP        || 30  ||  LINEOUT_R   
 
|-
 
|-
| 15 || EPHY-LED-LINK ||     || 31 ||  MIC_P
+
| 15 || EPHY-LED-LINK      || 31 ||  MIC_P
 
|-
 
|-
| 16 || EPHY-LED-SPD ||     ||  32 ||  MIC_N
+
| 16 || EPHY-LED-SPD    ||  32 ||  MIC_N
 
|}
 
|}
  
==硬件连接==
+
==Hardware Setup==
NanoPi Duo2可直接装配在NanoPi Duo2 IoT-Box底板上,装配时注意NanoPi Duo2的方向,参考下图连接模块:<br>
+
The NanoPi Duo2 can be mounted on the NanoPi Duo2 IoT-Box carrier board. You can refer to the following setup to assemble them:<br>
 
[[File:NanoPi_Duo2_NanoPi Duo2 IoT-Box.jpg|frameless|600px|NanoPi Duo2 IoT-Box_NanoPi_Duo2]]
 
[[File:NanoPi_Duo2_NanoPi Duo2 IoT-Box.jpg|frameless|600px|NanoPi Duo2 IoT-Box_NanoPi_Duo2]]
  
使用NanoPi Duo2 IoT-Box底板,能方便的使用有线网络、USB等接口<br>
+
You can connect your NanoPi Duo2 IoT-Box board to a network and external modules such as USB devices<br>
 
[[File:NanoPi Duo2 IoT-Box_USB2LCD.jpg|frameless|450px|NanoPi Duo2 IoT-Box]]<br>
 
[[File:NanoPi Duo2 IoT-Box_USB2LCD.jpg|frameless|450px|NanoPi Duo2 IoT-Box]]<br>
  
NanoPi Duo2 IoT-Box底板使用的GSM/GPRS天线和WiFi天线的频段不一样,请注意区分,参考下图装配:<br>
+
When you use the onboard quad-band GSM/GPRS module you should use an appropriate antenna and this antenna's band is different from an WiFi antenna's band. You can refer to the following setup:<br>
[[File:NanoPi Duo2 IoT-Box-ant.jpg|frameless|600px|NanoPi Duo2 IoT-Box 天线装配]]
+
[[File:NanoPi Duo2 IoT-Box-ant.jpg|frameless|600px|NanoPi Duo2 IoT-Box Assemble an antenna]]
  
==软件使用==
+
==Applications==
===1、GSM/GPRS模块的使用===
+
===Work with GSM/GPRS Module===
使用前请先插入可以使用的SIM卡,并装配GSM/GPRS天线:<br />
+
{{Linux-SIM800C}}
  
===2、USB Host接口的使用===
+
===Work with USB Host===
NanoPi Duo2 IoT-Box的USB Host接口可以方便的外接常用的USB设备,连接Matrix - LCD2USB如下所示:<br />
+
You can connect a USB device e.g. Matrix - LCD2USB to the NanoPi Duo2 IoT-Box board as follows:<br />
 
[[File:Matrix-LCD2USB_NanoPi Duo2 IoT-Box.jpg|frameless|600px|连接Matrix - LCD2USB]]
 
[[File:Matrix-LCD2USB_NanoPi Duo2 IoT-Box.jpg|frameless|600px|连接Matrix - LCD2USB]]
  
===3、音频输入与输出===
+
===Work with Audio Input & Output===
1、可使用以下命令录音:
+
1. Run the following command to record voices:
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
arecord -D hw:0,0 -f cd test.wav  
 
arecord -D hw:0,0 -f cd test.wav  
 
</syntaxhighlight>
 
</syntaxhighlight>
运行效果如下:<br>
+
Here is what you expect to observe:<br>
[[File:audio_in.jpg|frameless|600px|录音]]<br>
+
[[File:audio_in.jpg|frameless|600px|Voice Recording]]<br>
2、可使用以下命令播放音频文件,例如播放/root/Music/test.wav
+
2. Run the following command to play audio e.g. the /root/Music/test.wav file
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
  aplay /root/Music/test.wav
 
  aplay /root/Music/test.wav
 
</syntaxhighlight>
 
</syntaxhighlight>
运行效果如下:<br>
+
Here is what you expect to observe:<br>
[[File:audio_out.jpg|frameless|600px|播放音乐]]<br>
+
[[File:audio_out.jpg|frameless|600px|Audio Play]]<br>
 
<br>
 
<br>
可以使用alsamixer工具调节播放音乐的音量
+
You can use the alsamixer utility to adjust the volume.
  
==相关资料==
+
==Resources==
*[Schematic]([http://wiki.friendlyarm.com/wiki/images/d/d5/Schematic_NanoPi_Duo2_IoT_Box-1808.pdf Schematic_NanoPi Duo2 IoT-Box.pdf])
+
*[Schematic]([http://wiki.friendlyelec.com/wiki/images/d/d5/Schematic_NanoPi_Duo2_IoT_Box-1808.pdf Schematic_NanoPi Duo2 IoT-Box.pdf])
*[Dimension]([http://wiki.friendlyarm.com/wiki/index.php/File:Dimension_NanoPi_Duo2_IoT_Box_pcb-1808.rar Dimension_NanoPi Duo2 IoT-Box(dxf)])
+
*[Dimension]([http://wiki.friendlyelec.com/wiki/index.php/File:Dimension_NanoPi_Duo2_IoT_Box_pcb-1808.rar Dimension_NanoPi Duo2 IoT-Box(dxf)])
*[Manual]([http://wiki.friendlyarm.com/wiki/images/7/76/SIM800_Series_AT_Command_Manual_V1.10.pdf SIM800_Series_AT_Command_Manual_V1.10.pdf])
+
*[Manual]([http://wiki.friendlyelec.com/wiki/images/7/76/SIM800_Series_AT_Command_Manual_V1.10.pdf SIM800_Series_AT_Command_Manual_V1.10.pdf])
 +
 
 +
==Update Log==
 +
===Oct-10-2018===
 +
* Released English Version

Latest revision as of 07:19, 21 February 2022

查看中文

1 Introduction

NanoPi Duo2 IoT-Box Side
NanoPi Duo2 IoT-Box Front
NanoPi Duo2 IoT-Box Back
  • The NanoPi Duo2 IoT-Box is a dedicated carrier board for the NanoPi Duo2. It populates Ethernet port, serial port, audio and USB etc.
  • It has an onboard quad-band GSM/GPRS module SIM800C.
  • It has 2.0mm I2C interface, UART interface, audio interface and CVBS interface etc and can work with various external modules.
  • Its MicroUSB port is only used as power input. And a power switch is added too.
  • It has one power LED and one GPIO accessed LED.
  • It populates the two USB ports of the NanoPi Duo2.
  • It populates the serial ports and Ethernet port of the NanoPi Duo2.
  • It has an IPX to SMA antenna converter for WiFi antennas.

2 Hardware Spec

  • Onboard quad-band GSM/GPRS module
  • 2 x USB Host
  • Serial port and Ethernet port
  • Audio input and output
  • MicroUSB power input and a power switch
  • IPX to SMA WiFi converter
  • PCB dimension (mm): 85x56

NanoPi Duo2 IoT-Box_PCB

2.1 Layout

NanoPi Duo2 IoT-Box Layout

Here is the NanoPi Duo2 IoT-Box's layout. Its pins' remarks are printed on the board.

  • NanoPi Duo header Pin Spec
Number# Name Number# Name
1 VDD_5V 17 DEBUG_RX(UART_RXD0)/GPIOA5/PWM0
2 VDD_5V 18 DEBUG_TX(UART_TXD0)/GPIOA4
3 SYS_3.3V 19 GND
4 GND 20 I2C0_SCL/GPIOA11
5 GPIOL11/IR-RX 21 I2C0_SDA/GPIOA12
6 GPIOG11 22 UART3_TX/SPI1_CS/GPIOA13
7 USB-DM3 23 UART3_RX/SPI1_CLK/GPIOA14
8 USB-DP3 24 UART3_CTS/SPI1_MISO/GPIOA16
9 USB-DM2 25 UART3_RTS/SPI1_MOSI/GPIOA15
10 USB-DP2 26 UART1_RX/GPIOG7
11 EPHY-RXN 27 UART1_TX/GPIOG6
12 EPHY-RXP 28 CVBS
13 EPHY-TXN 29 LINEOUT_L
14 EPHY-TXP 30 LINEOUT_R
15 EPHY-LED-LINK 31 MIC_P
16 EPHY-LED-SPD 32 MIC_N

3 Hardware Setup

The NanoPi Duo2 can be mounted on the NanoPi Duo2 IoT-Box carrier board. You can refer to the following setup to assemble them:
NanoPi Duo2 IoT-Box_NanoPi_Duo2

You can connect your NanoPi Duo2 IoT-Box board to a network and external modules such as USB devices
NanoPi Duo2 IoT-Box

When you use the onboard quad-band GSM/GPRS module you should use an appropriate antenna and this antenna's band is different from an WiFi antenna's band. You can refer to the following setup:
NanoPi Duo2 IoT-Box Assemble an antenna

4 Applications

4.1 Work with GSM/GPRS Module

To test SIM800C you need to insert a SIM card and install a GSM/GPRS antenna.
By default the FriendlyCore system FriendlyElec provides has a Python demo for testing SIM800C. Run the following commands to test it:

$ cd /root/Python/GSM-GPRS/sim800-test
$ apt-get install python-pip
$ pip install --upgrade pip
$ pip install pyserial
$ ./sim800c-test.py -h              # Check help information
./sim800c-test.py -p <phone_number> -o <operator, cmcc> -w <website>
$ ./sim800c-test.py -p 136xxxxxxxx  -o cmcc -w www.baidu.com  # Visit baidu.com
Option Comment
-p specifies a telephone number for sim card.
-o specifies a telecom operator. For example "cmcc" stands for China Mobile Communication Corporation.
-w specifies a website to visit

By default this demo will load 1K bytes' data from the specified website and it takes a while. If it is successful you will see the following information:
Sim800c-surf.png

4.2 Work with USB Host

You can connect a USB device e.g. Matrix - LCD2USB to the NanoPi Duo2 IoT-Box board as follows:
连接Matrix - LCD2USB

4.3 Work with Audio Input & Output

1. Run the following command to record voices:

arecord -D hw:0,0 -f cd test.wav

Here is what you expect to observe:
Voice Recording
2. Run the following command to play audio e.g. the /root/Music/test.wav file

 aplay /root/Music/test.wav

Here is what you expect to observe:
Audio Play

You can use the alsamixer utility to adjust the volume.

5 Resources

6 Update Log

6.1 Oct-10-2018

  • Released English Version