Difference between revisions of "NanoHat PCM5102A"
From FriendlyELEC WiKi
(Created page with "查看中文 ==Introduction== NanoHat PCM5102A * The Matrix - NanoHat PCM5102A module uses TI's...") |
(→Update Log) |
||
| (6 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | [[ | + | [[NanoHat PCM5102A/zh|查看中文]] |
==Introduction== | ==Introduction== | ||
[[File:Matrix - NanoHat PCM5102A.jpg|thumb|NanoHat PCM5102A]] | [[File:Matrix - NanoHat PCM5102A.jpg|thumb|NanoHat PCM5102A]] | ||
| − | * The | + | * The NanoHat PCM5102A module uses TI's DAC audio chip PCM5102A and NS' low-noise, ultra-low dropout LP2992 regulator. PCM5102A's sample rates up to 384kHz and its resolution is 32-bit. |
* Its dynamic range is 112dB. Its THD+N at –1 dBFS is -93db. Its full-scale single-ended output is 2.1V. The SNR is 120dB. | * Its dynamic range is 112dB. Its THD+N at –1 dBFS is -93db. Its full-scale single-ended output is 2.1V. The SNR is 120dB. | ||
* Its onboard VS1838B infrared receiver allows it to be remote-controlled. | * Its onboard VS1838B infrared receiver allows it to be remote-controlled. | ||
| Line 50: | Line 50: | ||
|- | |- | ||
|12 ||GND || GND | |12 ||GND || GND | ||
| + | |} | ||
| + | |||
| + | ==Hardware & Software Systems that Work with NanoHat PCM5102A== | ||
| + | {| class="wikitable" | ||
| + | |- | ||
| + | |Index ||CPU Model|| Board Model || OS | ||
| + | |- | ||
| + | |1 ||H3||NanoPi NEO|| Allwinner's released Linux-3.4 kernel and Mainline Linux-4.x kernel | ||
| + | |- | ||
| + | |2 ||H3||NanoPi NEO Air || Allwinner's released Linux-3.4 kernel and Mainline Linux-4.x | ||
| + | |- | ||
| + | |3 ||H5||NanoPi NEO2 || Mainline Linux-4.x kernel | ||
| + | |- | ||
| + | |4 ||H5||NanoPi NEO Plus2 || Mainline Linux-4.x kernel | ||
|} | |} | ||
==Applications== | ==Applications== | ||
| − | The NanoHat PCM5102A can be stacked on | + | The NanoHat PCM5102A can be stacked on supported boards. Here is a hardware setup:<br> |
[[File:Matrix - NanoHat PCM5102A_nanopi_NEO.jpg|frameless|600px|Matrix - NanoHat | [[File:Matrix - NanoHat PCM5102A_nanopi_NEO.jpg|frameless|600px|Matrix - NanoHat | ||
| Line 59: | Line 73: | ||
==How to Play== | ==How to Play== | ||
| − | + | ===Under H3 & Linux-3.4 Kernel=== | |
| + | If you use a FriendlyElec's H3 board under Allwinner's released Linux-3.4 kernel run the following command to check whether or not the NanoHat PCM5102A is enabled: | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | $ aplay -l | ||
| + | **** List of PLAYBACK Hardware Devices **** | ||
| + | card 0: Pcm5102a [Pcm5102a], device 0: Playback pcm5102a-hifi-0 [] | ||
| + | Subdevices: 1/1 | ||
| + | Subdevice #0: subdevice #0 | ||
| + | card 1: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [] | ||
| + | Subdevices: 1/1 | ||
| + | Subdevice #0: subdevice #0 | ||
| + | </syntaxhighlight> | ||
| + | card 0 stands for pcm5102a. You can play an audio file by running the following command: | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | $ aplay /root/Music/test.wav -D plughw:0 | ||
| + | </syntaxhighlight> | ||
| + | -D plughw:0 stands for audio card 0. Connect your module to a speaker and you will hear your music. | ||
| − | + | ===Under H3/H5 & Linux-4.x Kernel=== | |
| + | If you use a FriendlyElec's H3/H5 board under Allwinner's released Linux-4.x kernel you need to enable the NanoHat PCM5102A with npi-config:<br> | ||
| + | Start npi-config as root: | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
| − | + | $ npi-config | |
</syntaxhighlight> | </syntaxhighlight> | ||
| − | + | Open the following menu:<br> | |
| − | [[File: | + | [[File:pcm5102a-1.png|frameless|1000px|pcm5102a-1]]<br> |
| + | Open I2S:<br> | ||
| + | [[File:pcm5102a-2.png|frameless|1000px|pcm5102a-2]]<br> | ||
| + | Enable/Disable I2S. By default I2S0 is disabled:<br> | ||
| + | [[File:pcm5102a-3.png|frameless|1000px|pcm5102a-3]]<br> | ||
| + | After you enable I2S0 I2C1 will be disabled.After I2S0 is enabled select pcm5102a:<br> | ||
| + | [[File:pcm5102a-4.png|frameless|1000px|pcm5102a-4]]<br> | ||
| + | Return to the main menu and do <Finish>. Reboot your system and run the following command to check whether or not the NanoHat PCM5102A is enabled: | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | $ aplay -l | ||
| + | **** List of PLAYBACK Hardware Devices **** | ||
| + | card 0: sndsun8ii2sdac [snd-sun8i-i2s-dac], device 0: sun8i-i2s-dac pcm5102a-hifi-0 [] | ||
| + | Subdevices: 1/1 | ||
| + | Subdevice #0: subdevice #0 | ||
| + | card 1: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 [] | ||
| + | Subdevices: 1/1 | ||
| + | Subdevice #0: subdevice #0 | ||
| + | </syntaxhighlight> | ||
| + | card 0 stands for pcm5102a. You can play an audio file by running the following command: | ||
| + | <syntaxhighlight lang="bash"> | ||
| + | $ aplay /root/Music/test.wav -D plughw:0 | ||
| + | </syntaxhighlight> | ||
| + | -D plughw:0 stands for audio card 0. Connect your module to a speaker and you will hear your music. | ||
==Resources== | ==Resources== | ||
| Line 75: | Line 129: | ||
===Jan-20-2017=== | ===Jan-20-2017=== | ||
* Released English version | * Released English version | ||
| + | |||
| + | ===July-4-2017=== | ||
| + | * Added section 3 | ||
| + | * Updated section 5: added details on how to play it with H3 and H5 boards under different kernels | ||
Latest revision as of 10:15, 3 July 2017
Contents
1 Introduction
- The NanoHat PCM5102A module uses TI's DAC audio chip PCM5102A and NS' low-noise, ultra-low dropout LP2992 regulator. PCM5102A's sample rates up to 384kHz and its resolution is 32-bit.
- Its dynamic range is 112dB. Its THD+N at –1 dBFS is -93db. Its full-scale single-ended output is 2.1V. The SNR is 120dB.
- Its onboard VS1838B infrared receiver allows it to be remote-controlled.
- This module has exactly the same dimension as the NanoPi NEO/Air and can be stacked on an NanoPi NEO/Air.
2 Hardware Spec
- Ultra-low out-of-band noise
- Audio data bit length: 16-bit, 24-bit and 32-bit
- Audio format selection: I2S (Low) / Left-justified
- Sampling frequency: 384KHz, resolution: 32-bit
- Onboard infrared receiver
- Pin Description:
NanoPi NEO/Air 24 Pin header is not listed here. Refer to NanoPi NEO/Air's wiki site for more details
NanoPi NEO
NanoPi NEO Air
12Pin header pin description:
| Pin | Name | Description |
| 1 | VDD_5V | 5V Power In |
| 2 | NC | Not Connected |
| 3 | NC | Not Connected |
| 4 | NC | Not Connected |
| 5 | NC | Not Connected |
| 6 | IR Receiver | IR Receiver |
| 7 | NC | Not Connected |
| 8 | LRCK | I2S/PCM Sample Rate Clock/Sync |
| 9 | BCK | I2S/PCM Sample Rate Clock |
| 10 | DIN | I2S/PCM Serial Data Input |
| 11 | NC | Not Connected |
| 12 | GND | GND |
3 Hardware & Software Systems that Work with NanoHat PCM5102A
| Index | CPU Model | Board Model | OS |
| 1 | H3 | NanoPi NEO | Allwinner's released Linux-3.4 kernel and Mainline Linux-4.x kernel |
| 2 | H3 | NanoPi NEO Air | Allwinner's released Linux-3.4 kernel and Mainline Linux-4.x |
| 3 | H5 | NanoPi NEO2 | Mainline Linux-4.x kernel |
| 4 | H5 | NanoPi NEO Plus2 | Mainline Linux-4.x kernel |
4 Applications
The NanoHat PCM5102A can be stacked on supported boards. Here is a hardware setup:
5 How to Play
5.1 Under H3 & Linux-3.4 Kernel
If you use a FriendlyElec's H3 board under Allwinner's released Linux-3.4 kernel run the following command to check whether or not the NanoHat PCM5102A is enabled:
$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Pcm5102a [Pcm5102a], device 0: Playback pcm5102a-hifi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0
card 0 stands for pcm5102a. You can play an audio file by running the following command:
$ aplay /root/Music/test.wav -D plughw:0
-D plughw:0 stands for audio card 0. Connect your module to a speaker and you will hear your music.
5.2 Under H3/H5 & Linux-4.x Kernel
If you use a FriendlyElec's H3/H5 board under Allwinner's released Linux-4.x kernel you need to enable the NanoHat PCM5102A with npi-config:
Start npi-config as root:
$ npi-configOpen the following menu:
Open I2S:
Enable/Disable I2S. By default I2S0 is disabled:
After you enable I2S0 I2C1 will be disabled.After I2S0 is enabled select pcm5102a:
Return to the main menu and do <Finish>. Reboot your system and run the following command to check whether or not the NanoHat PCM5102A is enabled:
$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: sndsun8ii2sdac [snd-sun8i-i2s-dac], device 0: sun8i-i2s-dac pcm5102a-hifi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0
card 0 stands for pcm5102a. You can play an audio file by running the following command:
$ aplay /root/Music/test.wav -D plughw:0
-D plughw:0 stands for audio card 0. Connect your module to a speaker and you will hear your music.
6 Resources
- [Schematic](Schematic - NanoHat PCM5102A.pdf)
- [Datasheet](PCM5102A)
7 Update Log
7.1 Jan-20-2017
- Released English version
7.2 July-4-2017
- Added section 3
- Updated section 5: added details on how to play it with H3 and H5 boards under different kernels
